BRX BRX160.2 / BRX320.4 / BRX640.4 / BRX1200.4 BRX1100.1D / BRX1600.1D / BRX2000.1D / BRX2400.1D BRX5000.
HIFONICS BRUTUS HIGH PERFORMANCE AMPLIFIERS The BRUTUS BRX Series products have been designed to a very high level of performance, with features unavailable in any other product. All of the amplifiers have variable crossovers built in, with added touches such as subsonic filter, bass equalization and an HFR-3 remote control module for the monoblocks that allows overall Level control from reach of the drivers seat.
GENERAL INSTALLATION PROCEDURE System Design The success of any car stereo system relies on several factors, such as the system design, execution of the installation, and system setup. Please remember that any system is only as good as its weakest link. Please remember that higher power systems are not necessarily useful purely for high sound pressure levels, but also to establish a headroom capability, to reproduce musical peaks cleanly without distortion.
AMPLIFIER FEATURE DESCRIPTIONS BRUTUS BRX AMPLIFIERS: Each model is capable of 4 & 2-Ohms stereo per channel, or 4-Ohms mono bridged operation except the mono amps which are capable of 4, 2 and 1-Ohm loads. Tri-Mode operation with any stereo pair of amplifier channels is possible, as with all bridgeable amplifiers. The input sensitivities for rated output powers are variable from 0.2V to 6V for the multi channel amplifiers and 0.2V to 9V for the mono models.
BRX160.2 2-CHANNEL AMPLIFIER APPLICATIONS 2 CHANNEL FULL RANGE SYSTEM Here we show how to use the 2 channel amplifiers as straightforward discrete 2 channel full range units. Interconnect cable checklist: - Connect the four inputs of the amplifier to a Radio/CD with quality RCA cables. Level control checklist: - Refer to the section “Setting up systems after installation for best performance” Minimum final loudspeaker impedances: - 2 ohm per channel. Switch setting checklist: - 1/2CH X-OVER: FULL 0.
BRX320.4 / BRX640.4 / BRX1200.4 4-CHANNEL AMPLIFIER APPLICATIONS 4 CHANNEL FULL RANGE SYSTEM Here we show how to use the 4 channel amplifiers as straightforward discrete 4 channel full range units. - HI PASS: N/A - LOW PASS: N/A Interconnect cable checklist: - Connect the four inputs of the amplifier to a Radio/CD with quality RCA cables.
BRX320.4 / BRX640.4 / BRX1200.4 4-CHANNEL AMPLIFIER APPLICATIONS Front/Rear high pass, using a mono amplifier for mono sub bass The combination of a mono and a 4 channel amplifier, utilizing their built in crossovers, makes it a snap to put together a full system with front and rear highs, with mono sub bass. Interconnect cable checklist: - Using good quality RCA cables, feed the front and rear outputs of a head unit to the inputs of the 4 channel amplifier as shown.
BRX5000.5 5-CHANNEL AMPLIFIER APPLICATIONS 5 channel discrete, one being mono low pass You can use this configuration simply as 4 discrete full range channels, with a 5th low pass channel. All of the crossovers are bypassed , except the LOW PASS on channel 5. The 5 channels can also be utilized with an outboard active crossover, or with crossovers in head units or equalizers. This setup is common when your headunit or crossover has 2 sets of full range RCA outputs and 1 set of mono subwoofer outputs.
BRX1100.1D / BRX1600.1D MONO AMPLIFIER APPLICATIONS Basic application Interconnect cable checklist: - Connect the line inputs to a Radio/CD RCA outputs or line output of the full range primary amplifier with good quality RCA cables. A “Y” adapter may be needed as shown in the diagram. - Use at least 16 gauge speaker wiring. These amplifiers have dual speaker terminals, simplifying the hookup of multiple speakers. The 2 positives are the same and the 2 negatives are the same.
BRX2000.1D MONO AMPLIFIER APPLICATIONS Basic application Interconnect cable checklist: - Connect the line inputs to a Radio/CD RCA outputs or line output of the full range primary amplifier with good quality RCA cables. A “Y” adapter may be needed as shown in the diagram. - Use at least 16 gauge speaker wiring. These amplifiers have dual speaker terminals, simplifying the hookup of multiple speakers. The 2 positives are the same and the 2 negatives are the same.
BRX2400.1D MONO AMPLIFIER APPLICATIONS Basic application SINGLE AMP INSTALLATION PROCEDURE: 1. Connect the amp LINE INPUTS to the Radio/CD player full range or mono line out puts with good quality RCA interconnect cables. 2. Plug in the HFR-3 remote module into the amp REMOTE INPUT jack. 3. Route a 0 gauge power cables directly to the vehicle battery with an in-line fuse. 4. Connect a 0 gauge ground cables directly to chassis ground with in 36” of the amp.
SETTING UP SYSTEMS AFTER INSTALLATION FOR BEST PERFORMANCE BRX160.2 / BRX320.4 / BRX640.4 / BRX1200.4 / BRX5000.5 General: At this point you are ready to get more specific on the settings for your amplifier. High Pass: -When in Hi Pass operation, this setting acts as a low frequency cut off for your system reproduction. The point that you set it at cuts off any frequencies from reproduction beyond this point. The 12 o’clock position is a great starting point.
TROUBLESHOOTING A SYSTEM The key to finding the problem in a misbehaving sound system is to isolate parts of that system in a logical fashion to track down the fault. Description of the Diagnostic system built into all HIFONICS amplifiers The diagnostic system will shut down the amplifier, until reset by turning the head unit off, and back on. This state of affairs will be indicated by the front panel PROTECT LED lighting up under the following conditions: 1 - A sort circuit on the loudspeaker leads.
12
Maxxsonics Limited Warranty As the manufacturer of Maxxsonics, MB Quart, Autotek, Crunch, Hifonics and MAXXLINK car audio products, Maxxsonics USA Inc. Warrants to the original consumer purchaser the amplifier to be free from defects in material and workmanship for one (1) Year from date of purchase. All other parts and accessories of the system are warrantied to be free from defects in material and workmanship for one (1) year from date of purchase.
14 Biggest POWER systems V3 Products, Level 10 Performance + 1 Year Warranty Moderate POWER systems V2 Products, Level 7 Performance + 6 Month Warranty Smaller POWER systems V1 Products, Level 5 Performance
15
PART#: A1212