Operating instructions

ManualsBrandsBryant ManualsConsumer electronicsII TSTAT-0-16

Programming and Operating Instructions

AT POWER UP

When power is first applied, AC or HP will appear for 5 seconds

to tell you it is an air conditioner (AC) or a heat pump (HP) model.

After this, the time display will flash to tell you the power has been

off. The day and time will show, within 10 minutes, when the

power went off. Pressing any button will stop the flashing.

A. Setting the current time:

1. Press the TIME/TEMP button. SET TIME flashes on the

display.

2. Press the Up or Down button until the correct time is

displayed.

3. To quickly advance to the proper time, press and hold the

UP or DOWN button.

4. When the correct time appears on the display, press the

HOLD/END button.

(Note: If you choose not to press the HOLD/END button,

the thermostat will automatically exit the time setting mode

after 10 seconds.)

B. Setting the current day:

1. Press the DAY button to advance to the correct day.

MANUAL OPERATION

A. To operate manually (without the programmed com-

fort schedule):

Press the HOLD/END button to make the HOLD icon appear.

Then follow the four steps below:

1. To Select the Mode:

Use the MODE button to move between the choices. OFF,

HEAT, COOL, or EMHT will appear on the display.

EMHT will only appear on heat pump models.

2. To Select the Fan Operation:

Use the FAN button to move between continuous fan

(indicated by the FAN ON icon) and auto fan operation.

3. To Read the Room Temperature:

The large display reads room temperature until a button is

pressed.

4. To Adjust the Set Point:

The first press of the UP or DOWN button does not change

the set point. It displays the current set point for a period of

5 seconds. Successive presses within this 5 seconds will

adjust the set point and restart the 5 seconds. During the 5

seconds, the SET TEMP icon will be flashing.

PROGRAMMED OPERATION

Introduction: The Standard Programmable Thermostat provides

four periods per day (MORNING, DAY, EVE, NIGHT) and two

schedules per week (MoTuWeThFr and SaSu). A separate time,

heat set point, and cool set point can be set for each period and

schedule. Before starting to actually program the thermostat, fill

out Table 1 with the values you wish to program. (The Energy

Star, US Department of Energy recommended time and tempera-

ture values are already programmed for you as a starting point and

are shown on the left side of the table.)

The first press of the PROGRAM button brings up the program-

ming mode and places you at the current day and period.

Successive presses move you between the four daily periods.

WHILE PROGRAMMING:

The TIME/TEMP button moves between selections of SET TIME,

SET TEMP and HEAT, and SET TEMP and COOL. These three

numbers are to be programmed for each of the periods MORN-

ING, DAY, EVE, and NIGHT.

The DAY button moves between the weekdays, (MoTuWeThFr)

and the weekend (SaSu) selections. A different schedule may be

set for the weekdays and the weekend.

You may exit programming at any time by pressing the

HOLD/END button.

PROGRAMMING A WEEKLY COMFORT SCHEDULE:

1. Press the PROGRAM button. The word PROGRAMMING

appears on the display and the words SET TIME flash on

the display. MoTuWeThFr or SaSu and the present period

icons will appear on the display. The current mode (HEAT

or COOL) will also show. Use the DAY button to select

weekdays and the PROGRAM button to select MORNING.

2. Press the UP or DOWN button to set the start time for

MORNING (box 1 value).

3. Press the TIME/TEMP button until COOL is on and SET

TEMP flashes on the display.

4. Press the UP or DOWN button to select the cooling

temperature set point (box 2 value).

5. Press the TIME/TEMP button until HEAT is on and SET

TEMP flashes on the display.

6. Press the UP or DOWN buttons to select the heating

temperature set point (box 3 value).

7. Press the DAY button to advance to the next time period.

Enter time and temperature settings from boxes 4 through

12 for the periods DAY, EVE, and NIGHT by following

steps 2-6 above.

Fig. 1—Standard Programmable Thermostat

A99069

Homeowner’s Guide/

Installation Instructions

STANDARD PROGRAMMABLE THERMOSTAT

Cancels: II TSTAT-0-23 II TSTAT-0-28

7-99

TSTAT

—1—

Summary of content (8 pages)

PAGE 1
Homeowner’s Guide/ Installation Instructions TSTAT STANDARD PROGRAMMABLE THERMOSTAT Cancels: II TSTAT-0-23 II TSTAT-0-28 7-99 Programming and Operating Instructions AT POWER UP When power is first applied, AC or HP will appear for 5 seconds to tell you it is an air conditioner (AC) or a heat pump (HP) model. After this, the time display will flash to tell you the power has been off. The day and time will show, within 10 minutes, when the power went off. Pressing any button will stop the flashing. A.
PAGE 2
TABLE 1—PROGRAMMING TABLE ENERGY STAR FACTORY DEFAULT VALUES PERIOD TIME COOL HEAT MORNING DAY EVE NIGHT 6:00 A.M. 8:00 A.M. 5:00 P.M. 10:00 P.M. 78 85 78 82 68 60 68 60 NEW COMFORT SCHEDULE MoTuWe ThFr TIME 1) 4) 7) 10) COOL 2) 5) 8) 11) 8. Press the DAY button to change between weekday and weekend programming. To set the weekend schedule, repeat steps 2 through 6, entering values in boxes 13 though 24. 9. Press END/HOLD to exit the programming mode.
PAGE 3
Installation, Start-Up, and Operating Instructions NOTE: Read the entire instruction manual before starting the installation. • SAFETY CONSIDERATIONS Read and follow manufacturer instructions carefully. Follow all local electrical codes during installation. All wiring must conform to local and national electrical codes. Improper wiring or installation may damage thermostat. . Recognize safety information.
PAGE 4
III.
PAGE 5
IV. THERMOSTAT OPERATION V. CHECK THERMOSTAT OPERATION A. Temperature Display A. Fan Operation Thermostat will display room temperature until UP or DOWN button is pressed. The word SET appears when these buttons are pressed and the current set point is displayed. If no buttons are pressed for 5 sec, the display will change back to show room temperature. B. 1. Press FAN button. This will start continuous fan operation. FAN ON icon will turn on. 2. Press FAN button again.
PAGE 6
AC THERMOSTAT HEATING W W FAN G G 24 VAC HOT R R 24 VAC COMM C COOLING Y N/A O * 270 Ω, 10 W * RESISTOR (SUPPLIED) C C Y Y TYPICAL FAN COIL/ FURNACE AC THERMOSTAT TYPICAL FAN COIL/ SINGLE-SPEED FURNACE AIR CONDITIONER HEATING W W FAN G G 24 VAC HOT R R 24 VAC COMM C COOLING Y N/A O * 270 Ω, 10 W * RESISTOR (SUPPLIED) C Y * See note 1 A99115 * See note 1 A99114 Fig. 3—Typical Heat Only Fig.
PAGE 7
✂ STANDARD PROGRAMMABLE THERMOSTAT CONFIGURATION RECORD Date __________________ Owner/Operator __________________________ Thermostat Model No. ______________________________ Indoor Unit Model No. _____________________ Outdoor Unit Model No.
PAGE 8
SERVICE TRAINING Packaged Service Training programs are an excellent way to increase your knowledge of the equipment discussed in this manual, including: • Unit Familiarization • Maintenance • Installation Overview • Operating Sequence A large selection of product, theory, and skills programs is available, using popular video-based formats and materials. All include video and/or slides, plus companion book.