User Manual Rider 320
Table of Contents Getting Started...................... 4 Your Rider 320............................... 4 Accessories.................................... 5 Status Icons.................................... 5 Step 1: Charge Your Rider 320........ 6 Step 2: Turn On Rider 320............... 6 Step 3: Initial Setup........................ 6 Step 4: Acquire Satellite Signals........................................... 7 Step 5: Ride Your Bike with Rider 320.......................................
WARNING Always consult your physician before you begin any training. Please read the details in Warranty and Safety Information guide in the package. Australian Consumer Law Our goods come with guarantees that can not be excluded under the New Zealand and Australian Consumer Laws. You are entitled to a replacement or refund for a major failure and for compensation for any other reasonably foreseeable loss or damage.
Getting Started This section will guide you through the basic preparations before you start using your Rider 320. Your Rider 320 A POWER/ BACKLIGHT D PAGE B PAUSE/ BACK A Power/Backlight ( B BACK ( C OK/LAP( D PAGE ( ) • Press to turn the device on. • Press to turn on/off the backlight while the device is on. • Long press to turn the device off . ) • In Cycling mode, press to enter Menu page. • In Menu, press to return to the previous page or cancel an operation.
Accessories The Rider 320 comes with the following accessories: • USB cable • Bike mount Optional items: • Smart Heart Rate Sensor • Smart Cadence Sensor • Race Mount-Rider • Smart Speed Sensor • Smart Speed / Cadence Dual Sensor • Sport Mount Status Icons Icon Description Icon Description Bike Type 1 2 Heart Rate Sensor is active Bike 1 Cadence Sensor is active Bike 2 Speed Sensor is active GPS Signal Status Dual Sensor is active No signal (bot fixed) Power Meter is active Weak signal L
Step 1: Charge your Rider 320 Connect Rider 320 to a PC to charge the battery for at least 4 hours. Unplug the device when it is fully charged. • You may see a white screen when the battery is really low. Keep the device plugged for several minutes, it will automatically turn-on after battery is properly charged. • The temperature suitable for charging battery is 0˚C~40˚C. Beyond this temperature range, charging will be terminated and the device will draw power from battery.
Step 4: Acquire Satellite Signals Once the Rider 320 is turned on, it will automatically search for satellite signals. It may take 30 to 60 seconds to acquire signals. Please make sure you acquire the satellite signal for the first time use. The GPS signal icon ( / ) appears when GPS is fixed. • If the GPS signal is not fixed, an icon appears on the screen. • Please avoid the obstructed environments since they might affect the GPS reception.
Share Your Records Upload Your Tracks to Brytonactive.com 1. Sign up/log in Brytonactive.com a. Go to https://active.brytonsport.com. b. Register a new account or use your current account to log in. 2. Connect to PC Turn on your Rider 320 and connect it to your computer by USB cable. 3. Share Your Records a. Click "+" on the upper right corner. b. Drop FIT, BDX, GPX file(s) here or Click “Select files“ to upload tracks. c. Click “Activities” to check uploaded tracks. Share Your Tracks to Strava.com 1.
Auto Sync Tracks to Bryton Active App No more uploading tracks manually after riding. Bryton Active App automatically syncs your track after pairing with your GPS device. a. Scan QR code below to download Bryton b. Go to Settings>Device Manager>”+”> Rider 320 to add your GPS device. Active App or go to Google Play/App Store to search Bryton Active App. Then, log in or create an account. Rider 420 http://download.brytonsport.com/inst.html c. Check if UUID shown on app is the same as your device.
Bryton Update Tool Bryton Update Tool is the tool for you to update firmware. 1. Go to http://www.brytonsport.com/#/supportResult?tag=BrytonTool and download Bryton Update Tool. 2. Follow the on-screen instructions to install Bryton Update Tool. Update Firmware Bryton releases a new firmware version on irregular basis to add new functions or correct bugs for better and more stable performance. It is recommended that you update firmware once new firmware available.
View History You can veiw exercise record on your device right after your ride, and delete any unwanted record to gain more storage. View Exercise/Training Record Rider 320 provides graphical track summary, detail workout data , lap data and graphical analysis for you to have a better idea of your workout performance. History To view your history: View 1. In the main screen, press and press to enter. Delete 2. Press Delete All to select View History to enter View. 3.
History Flow ride = Ride Time 09/19 21:44 AVG 00:02:25 3.69 39 04 laps More 1/20 ride km kcal Record#/Total records Lap 01 MAX 75.6 75.6 39 39 19 19 kmh bpm rpm 00:49 0.25 81.4 13 0 0 km kmh kcal bpm rpm The arrow appears only when there is lap in this record..
Settings In Settings, you can customize Exercises settings, GPS system, General settings, Sensor settings, Altitude, Bike and User profile. You can also customize most used device settings via Bryton Active App. 1. In the main screen, press Settings 2. Press Exercises to select Settings. to enter Settings menu. GPS System General Sensors Data Page You can set the display settings for the Meter and Lap or you can customize data page via Bryton Active App. Please refer to page 32 to learn how to do it.
NOTE: The number of data fields shown on the screen depends on the “Data fields“ selection. 2-grid display 3-grid display NOTE: If Data Page is set to Auto, Rider 320 will automatically adjust its data field display when detecting the paired sensors. Speed HR CAD RTime Dist. Lap Display to enter Exercises 1. In the Settings menu, press > Data Page. Cycle Lap Data Page 1 2. Press On Data Page 2 On 3. Press and then to enter Lap. to enter Data Fields. 4.
Smart Lap With Smart Lap feature, you can use your device to automatically mark the lap at a specific location or after you have traveled a specific distance. Lap by Location By Location Use current location as Lap Yes 1. In the Settings menu, press to enter Exercises. Press. and then to select Smart Lap. to enter editing menu. Press 2. Press select Location and press to confirm. to 3. A “ Use current location as Lap” message pops up on to confirm this setting. the screen. Press 4.
Set Alert With the Alert feature, the device displays a message to notify you if: • your heart rate exceeds or drops below a specific number of beats per minute (bpm). • you excees or drop below a custom speed setting during your side. • your cadence speed exceeds or drops below a specific number of revolutions of the crank arm per minute (rpm). • you reach a certain amount of distance for the long workouts. • you reach a certain amount of time for the long workouts. 1.
Data Record With Data Record function, you can set your odometer and activate 1 second mode to get more accurate data. Set ODO ODO Setup O DO Setup All Recording 1 Sec mode 1. In the Settings menu, press Exercises. Press. and then Data Record. to enter to select to enter ODO Setup and press to 2. Press select desired setting and press to confirm. 3. Press to exit this menu.
GPS System Rider 320 has full GNSS (Global Navigation Satellite System) support including GPS , GLONASS (Russia), BDS (China), QZSS (Japan) and Galileo (EU). You can select the suitable GPS Mode according to your location to enhance accuracy or suit your needs. Choose Different Satellite Navigation System This setting allows you to switch between different satellite navigation systems to suit you best. GPS Mode GPS Mode GPS Mode GPS Mode GPS Mode GPS+BDS GPS+GLO GPS Power Save Off 1.
Change System Settings You can customize the device system setting such as backlight off, key tone, sound, time/ unit, on-screen display language. Backlight off Backlight Off Auto 1. In the Settings menu, press to select General. and then press 2. Press to enter System. 3. Press to enter Backlight Off. 4. Press to select desired setting and press to confirm. 5. Press to exit this menu. Key Tone Key Tone 1. In the Settings menu, press to select General. 2.
Sound Sound On 1. In the Settings menu, press to select General. and then press 2. Press to enter System. 3. Press confirm. to select Sound and press 4. Press to to select desired setting and press to confirm. 5. Press to exit this menu. Time/Unit Dlight Save Date Format Time Format Unit +0:00 dd/mm/yyyy 24hr KM,KG Time format Unit Daylight Save Temperature Date format 1. In the Settings menu, press to select General. 2. Press ˚C 3. Press confirm. and then press to enter System.
Contrast You can adjust contrast on your device. Contrast 1. In the Settings menu, press to select General. 2. Press and then press to enter System. 3. Press confirm. to select Contrast and press 4. Press to adjust desired contrast. 5. Press to exit this menu.
Bluetooth Before pairing Rider 320 with your bluetooth enabled mobile phone, make sure t he bluetooth function of your mobile phone and Rider 320 is turned on. Enable Bluetooth Enable On 1. In the Settings menu, press to select General. and then press 2. Press confirm. to select Bluetooth and press 3. Press to turn on/off bluetooth. 4. Press to exit this menu.
Configure Auto Scroll When the feature is enabled, the device will automatically switch pages at the preset time. Auto Scroll Auto Scroll On Interval 5 sec 1. In the Settings menu, press select General. 2. Press confirm. and then press to to select Auto Scroll and press to 3. Press to select the setting that you want to change and press to enter its submenu. • Auto scroll: enable/disable the auto switch. • Interval: set the interval time. 4. Press to exit this menu.
Start Reminder When Rider 320 detects the motion of your bike, it would pop up a reminder to ask you if you would like to record or not. You can set the frequency of start reminder. Start Remind 1. In the Settings menu, press to select General. and then press to select Start Remind and press 2. Press to confirm. Once 3. Press 4. Press to select desired setting and press to confirm. to exit this menu. View Memory Usage View the storage status of the device. 1.
Reset Data You can restore your Rider 320 to factory settings. General Perform factoryOnce reset ? Yes Data Reset 1. In the Settings menu, press to select General. 2. Press confirm. and then press to select Data Reset and press to select “YES” and press 3. Press confirm factory reset. 4. Press to to to exit this menu. NOTE: Factory reset operation will restore device to factory default settings.
ANT+/ BLE Sensors Rider 320 is compatible with both ANT+ and BLE sensors. You can customize the respective sensor settings such as rescan the sensor to pair with your device or enable/ disable the function. Exercises UUID General Sensor Heart Rate Sensors Settings > Heart Rate Speed Cadence Speed/CAD Power Di2 ANT+ Sensors Heart Rate > Status: Off ID: Heart Rate Rescan > More Or BLE Sensors Heart Rate Status: Set Status: Set Type: ANT+ Type: BT ID XXXXXXXXX Bryton HR XXXX More More 1.
NOTE: • Please refer to page 39-40 for sensors installation. • While pairing your speed/cadence sensor/the heart rate belt and power meter, please make sure there is no other cadence/speed sensor/power meter within 5m. • Bryton smart sensors can only be paired when they are awake, or they would go back to sleep to preserve power. • When the heart rate monitor is paired, the , heart rate icon appears on the main appears on the main screen. When cadence sensor is paired, the cadence sensor icon screen.
Altitude After receiving GPS signal, the Rider 320 will calibrate altitude automatically based on GPS altitude data. You can also set the altitude setting for the current location and four other locations manually. Current Altitude Altitude 1. In the Settings menu, press to select Altitude. 2. Press 31 and then press to enter Altitude. 3. Press press to adjust value of current altitude and to confirm. 4. Press to exit this menu.
Persnalize User Profile You can change your personal information. 1. In the Settings menu, press to select Profile. User Gender Male Birthday 1982/01/01 Height 177 cm and then press 2. Press to enter User Profile. A message of“Input correct profile as it might affect analysis.”pops up. Press to confirm after reading message. 3. Press to select setting that you want to edit and press to enter its submenu. • Gender : select your gender. • Birthday: set your Birthday. • Height: set your height.
Personalize Bike Profile You can customize and view your bicycle(s) profile. Bike 1 1. In the Settings menu, press to select Profile. Spd Source 2. Press Weight 13kg Wheel 1700mm and then press to select Bike Profile and press to enter. 3. Press to select setting that you want to edit and press to enter its submenu. • Spd Source: set the priority of the speed sources • Weight: set the bike weight. • Wheel: set the bike wheel size. • Activate: select to activate the bike. 4. Press 5.
Adjust Odometer Bike 1+2 ODO 1033km Ride Time Alt.Gain 89:23:28 8600m 1. In the Settings menu, press to select Profile. 2. Press and then press to select Bike Profile and then press to enter. to select Overview and press 3. Press enter its submenu. to to select Bike 1+2 and press to 4. Press confirm. enter into ODO setting page. 5. Press 6. Press confirm. to adjust ODO and press 7. Press to exit this menu. to Reset ODO You can reset the distance of Trip 1, Trip 2 and odometer. 1.
Bryton Active App Advanced Settings After pairing your Rider 320 with Bryton Active App, you will have access to System Language, Grid Setting, Altitude Calibration and Notifications. System Language You can change device language via Bryton Active App. 1. Pair Rider 320 with Bryton Active App 2. Go to Settings > General > System Language in Bryton Active App. 3. Select your prefered language. 4.
Altitude Calibration After receiving GPS signal, the Rider 320 will calibrate altitude automatically based on GPS altitude data. Altitude can also be changed manually or automatically updated by turning on the Auto Calibrate Altitude feature on the Bryton Active App. 1. Pair Rider 320 with Bryton Active App. 2-1. Calibrate Altitude Manually a. Select Alt. Cal in Bryton Active App. b. Bryton Active App will show the current location’s altitude.
Notifications After pairing your compatible smartphone using Bluetooth Smart wirelessly technology with Rider 320 , you can receive phone call, text and email notifications on your Rider 320. 1. IOS Pairing a. Go to Settings > General > Bluetooth to turn on Bluetooth on Rider 320. b. Go to your phone Settings > Bluetooth and enable Bluetooth. c. Go to the Bryton Active app and choose Settings > Device Manager > + . d. Select and add your device by pressing +. e. Tap Pair to pair your device with your phone.
Appendix Specifications Rider 320 Item Display Physical Size Weight Operating Temperature Battery Charging Temperature Battery Battery Life ANT+™ GNSS BLE Smart Water Resistant Barometer Description 2.3” FSTN positive transflective dot-matrix LCD 49.9 X 83.9 X 16.9mm 67g -10°C ~ 60°C 0°C ~ 40°C Li polymer rechargeable battery 35 hours with open sky Featuring certified wireless ANT+TM connectivity. Visit www.thisisant.com/directory for compatible products.
Smart Cadence Sensor Item Physical size Weight Water Resistance Transmission range Battery life Operating temperature Description 36.9 x 31.6 x 8.1 mm 6g Incidental exposure to water of up to 1 meter for up to 30 minutes. 3m Up to 1 year -10°C ~ 60°C 2.4GHz / Bluetooth 4.0 and Dynastream ANT+ Sport wireless Radio frequency/protocol communications protocol NOTE: Accuracy may be degraded by poor sensor contact, electrical, magnectic interference and distance from the transmitter.
To replace the battery: 1. Locate the circular battery cover on the back of sensors. 2. Use your finger to press and twist cover counter-clockwise so the indicator on the cover points to unlock icon ( ). 3. Remove the battery and insert new battery with positive connector first into the battery chamber. 4. Use your finger to press and twist cover clockwise so the indicator on the cover points to locked icon ( ).
Install Rider 320 Use Bike Mount to Mount Rider 320 1 2 3 4 (Optional) 1 2 Appendix 38
Install Speed/Cadence/Dual Sensor (Optional) Cadence Sensor + Speed Sensor + + NOTE: • Once sensors waken, the LED blinks twice. The LED continues to blink when you continue to pedal for pairing. After around 15 blinks, it will stop blinking. If not used for 10 minutes, sensor would go into sleep mode to preserve power. Please complete the pairing during the time the sensor is awake.
Install Heart Rate Belt (Optional) Strap Electrodes O ENP NOTE: • In cold weather, wear appropriate clothing to keep the heart rate belt warm. • The belt should be worn directly on your body. • Adjust the sensor position to the middle part of the body (wear it slightly below the chest). The Bryton logo shown on the sensor should be facing upward. Tighten the elastic belt firmly so that it will not turn loose during the exercise.
Wheel Size and Circumference The wheel size is marked on both sides of the tires. Wheel Size 12x1.75 12x1.95 14x1.50 14x1.75 16x1.50 16x1.75 16x2.00 16x1-1/8 16x1-3/8 17x1-1/4 18x1.50 18x1.75 20x1.25 20x1.35 20x1.50 20x1.75 20x1.95 20x1-1/8 20x1-3/8 22x1-3/8 22x1-1/2 24x1.75 24x2.00 24x2.125 24x1(520) 24x3/4 Tubular 24x1-1/8 24x1-1/4 26x1(559) 26x1.25 26x1.40 26x1.50 26x1.75 26x1.95 26x2.10 26x2.125 26x2.
Basic Care For Your Rider 320 Taking good care of your device will reduce the risk of damage to your device. • Do not drop your device or subject it to severe shock. • Do not expose your device to extreme temperatures and excessive moisture. • The screen surface can easily be scratched. Use the non-adhesive generic screen protectors to help protect the screen from minor scratches. • Use diluted neutral detergent on a soft cloth to clean your device.
Data Fields Category Energy Data Fields Calorie Kilojoules Altitude Max Altitude Alt. Gain Alt. Loss Gradient Uphill Downhill Distance Odometer LapDistance Distance LLapDist. Altitude Trip 1/Trip 2 Speed Avg Speed Max Speed Speed LapAvgSpd LapMaxSpd LLapAvgSpd Time Ride Time Trip Time Sunrise Time Sunset LapTime LLapTime Lap Count Cadence Avg CAD Cadence Max CAD LapAvgCad LLapAvgCad Description of Data Fields The number of total calories burned.
Category HR Temp Power Data Fields Description of Data Fields The number of times your heart beats per minute. It requires Heart Rate compatible HR sensor pairing connection to your device. Avg HR The average heart rate for current activity. Max HR The maximum heart rate for current activity. Your current heart rate divided by Maximum Heart Rate. MHR means that the maximum number of beats made by MHR % your heart in 1 minute of effort. (MHR is different from Max HR.
Category Power Pedal Analysis Data Fields Description of Data Fields The current range of your Maximum Aerobic Power Pecentage MAP Zone (Zone 1 to Zone 7). MAP% The current power divided by your Maximum Aerobic Power. FTP% The current power divided by your functional threshold power. Lap NP Normalized power of the current lap Last Lap NP Normalized power of the last lap LLapAvgPw The average power output for the last finished lap. LlapMaxPw The maximum power for the last finished lap.
RF Exposure Information (MPE) This device meets the EU requirements and the International Commission on Non-Ionizing Radiation Protection (ICNIRP) on the limitation of exposure of the general exposure requirements, this equipment must be operated in a minimum of 20 cm separation distance to the user. Hereby, Bryton Inc. declares that the radio equipment type Bryton product is in compliance with Directive 2014/53/EU.
