Soundweb London BLU-80/BLU-32/BLU-16 Installation Guide TM ZM10102-01-C
IMPORTANT SAFETY INSTRUCTIONS WARNING FOR YOUR PROTECTION PLEASE READ THE FOLLOWING: KEEP THESE INSTRUCTIONS HEED ALL WARNINGS FOLLOW ALL INSTRUCTIONS The symbols shown above are internationally accepted symbols that warn of potential hazards with electrical products. The lightning flash with arrowpoint in an equilateral triangle means that there are dangerous voltages present within the unit.
IMPORTANT SAFETY INSTRUCTIONS U.K. MAINS PLUG WARNING A molded mains plug that has been cut off from the cord is unsafe. Discard the mains plug at a suitable disposal facility. NEVER UNDER ANY CIRCUMSTANCES SHOULD YOU INSERT A DAMAGED OR CUT MAINS PLUG INTO A 13 AMP POWER SOCKET. Do not use the mains plug without the fuse cover in place. Replacement fuse covers can be obtained from your local retailer. Replacement fuses are 13 amps and MUST be ASTA approved to BS1362.
Regulatory information An example of this equipment has been tested and found to comply with the following European and international Standards for Electromagnetic Compatibility and Electrical Safety: Radiated Emissions (EU): EN55103-1 (1996) Immunity (EU): EN55103-2 (1996) Electrical Safety (EU): EN60065 (2002) Radiated Emissions (USA): FCC part 15 Class B Electrical safety (USA): UL60065 (2005) Important user information Do not remove covers.
Front panel Input card monitoring Each channel has 3 LED indicators showing: Clip Illuminated - Indicates clipping in the analogue domain for each channel of the fitted Input or Output card. The LED will illuminate at +18.5dB. Signal Illuminated - The Signal LED will illuminate for each channel of a fitted Input or Output card when the signal reaches or exceeds the signal threshold of -20dB.
Front panel details Audio cable wiring All audio and control connections to the BLU-80/BLU-32/BLU-16 are via Klippon pluggable terminal block connectors (also known as BL, Phoenix or Combicon). 6-way female Klippon connectors are supplied for making these connections. Audio Input and Output wiring convention Soundweb products provide cable shielding ‘back from the destination’ to eliminate ground loop problems.
Rear panel BLU-80 shown. BLU-32 layout is identical. BLU-16 has no CobraNetTM or Buddy Link connections but is otherwise identical to the BLU-80 and BLU-32. AC Mains AC Mains input to the universal switched-mode power supply, operates over a wide range of AC input voltages from 85V to 270V, 50/60Hz. CobraNet Connectors Primary/Secondary The CobraNetTM compatible devices within the SoundwebTM London system are fitted with a Peak Audio CobranetTM CM-1 module.
CONTROL INPUTS Used to connect switches or potentiometers, e.g. BLU-3 selector wallplate (Part no. ZBLU-3). Looking at the control port connector (on the back of the unit), there are two common (ground) connections C to the left of the eight CONTROL INPUTS and, two software assignable reference voltage outputs R to the right. The control ports now have two modes of operation. In Soundweb Designer’s Control Ports window these are labelled ‘2-wire’ and ‘3-wire’.
47kOhm log potentiometer 10K-100kOhm linear potentiometer ladder 1k 3600R ladder switch 1k 1200R 4k7 1k 1800R switch 1k unconnected 470R 2 wire mode 3 wire mode +supply voltage relay relay LED ground
Technical specifications INPUTS Up to 16 Analogue; electronically balanced on Phoenix/Combicon removable screw connectors. Mic/Line Inputs: Nominal gain 0dB, electronically switchable up to +48dB,in +6dB steps, input impedance 3.5kOhm +20dBu with 0dB input gain, (+8dBu with 12dB gain) >75dB at 1kHz <-128dBu typ with 150 Ohms source 48V nominal, selectable per input Maximum input level: CMRR: Equiv.
DECLARATION OF CONFORMITY Manufacturer’s Name: Manufacturer’s Address: BSS Audio 8760 S. Sandy Parkway Sandy, Utah 84070, USA declares that the product: Product name: BLU 16, BLU 32, BLU 80 Note: Product name may be suffixed by the letters-EU.
BSS Audio 8760 South Sandy Parkway Sandy, Utah 84070 801-566-8800 www.bssaudio.