This equipment has been designed for the normal use. It is certified to comply with Electron Wave Suitable Registration. The user this equipment in everywhere including residential areas. 151P USER GUIDE Notice This equipment is one of first class quality. The LCD panel is composed of more than 2 Million pixels and may have some faulty pixels. LCD panels with a maximum of 10 faulty pixels are classified as products of good quality. This standard is accepted by other manufacturers of LCD panels.
Please observe all following rules for installation, usage, and services so as to not defeat the safeguards incorporated into this monitor. Safety precautions are divided into Warning and Attention. Warning : Please ensure that no water leaks or gets onto or into the LCD monitor. Accidental exposure to water may cause fire or electrical damage. If case occurs, please turn off and unplug the monitor. If there is smoke or abnormal noises, please contact the store or customer service center.
Provide a secure connection to the power supply and do not use damaged power cords or plugs. Electrical shock or fire hazard may result. Do not place the monitor in exposed places or near water. Do not clean the monitor with water or touch it with wet hands. -Electrical shock or fire hazard may result. During lightening storms, unplug the monitor from the wall outlet and do not touch it.
Not using the monitor for hours, unplug the monitor from the wall outlet. - Dust may cause heat, fire, shock or short circuit If you use an outdoor antenna, be ensure that no water leaks through connectors and get onto the monitor. - Any liquid spill on the TV may cause fire or electric shock In case of any smoke or abnormal noise, immediately stop use of product and pull the power cord from the wall outlet. Then call your local dealer or service representative for assistance.
Install the monitor in stable place. - An unstable monitor may crash or fall. Personal injury, damage, or malfunction may result. Do not block ventilation openings with any curtain or tablecloths. - The increase of inside temperature may cause fire DO not drop the unit or make any scratch on the panel when you move the product. -Any scratch on the panel or drop of the product may cause functional failure. When moving the monitor, turn it off and disconnect all cables and the plug.
When disconnecting from the wall outlet, grab the plug. - Grabbing the cord may result in heat generation or fire hazard. Keep your eyes 20 inch away from the screen and 0~15° down in relation to the screen. - Viewing at too close a position and wrong posture can weaken your eyes. Do not press hard with your finger or scratch with sharp object on the surface of the LCD. -Any damage on the surface of the LCD may cause functional failure.
Do not use any chemicals such as industrial polisher, abrasive solution, wax, benzene, alcohol, or clearing detergents. - Chemical cleaners may fade, dissolve, or crack the monitor surface. If you install outdoor antenna, be sure to install it at the distance from power wire. - If the antenna contacts with the power wire, it may cause electric shock. Be sure to keep the distance of the outdoors antenna so that it would not touch electric wire in case it falls by heavy wind.
1. Select Button : Displays a OSD of all of the available input source. (PC / TV / VIDEO 1 / VIDEO 2). Exit the active the OSD 2. PIP Button : Activates PIP(Picture-in-Picture) window directly in PC mode. Selects video sources(Video/S-VHS/TV) 3. Auto Button : Allows the monitor to self-adjust to the incoming video signal. 4. Menu Button : Use this button to open the OSD and activate a highlighted menu items. 5. Channel Buttons : Increases or decreases the channel number.
1. Power In Terminal Connect the DC Adaptor to the power terminal on the back of the monitor. 2. D-SUB Terminal Connect the monitor D-SUB connector and the PC using the D-SUB signal cable. 3. S-Video Input Terminal Connect S-Video cable to this input. 4. Composite Video Input Terminal Connect video cable to this input. 5. Audio Input (Left) Terminal Connect left audio cable to this input. 6. Audio Input (Right) Terminal Connect right audio to this input. 7.
Please make sure the following items are included with your monitor. If any items are missing, contact your dealer.
Attention : Power off your Monitor before making any connections. 1. Power Connection : Connect the DC Adaptor to the power terminal on the back of the monitor. 2. Connection of PC : Connect the signal cable(D-SUB cable) to the monitor output socket of the computer and the other end to D-SUB on the back of the monitor. 3. AUDIO IN : Connect an audio cable to AUDIO IN on the back of the Monitor and the other end to AUDIO OUT terminal of the sound card on your computer.
1. Connecting VIDEO 1 1) Connect RCA cable(Yellow) to VIDEO terminal on the back of the monitor and the other end to an appropriate external A/V device such as VCR, DVD. 2) Connect Audio RCA cable(White, Red) to STEREO terminal on the back of the monitor and the other end to an appropriate external A/V device such as VCR, DVD.
2. Connecting VIDEO 2 1) Connect S-VHS cable to an appropriate external A/V device such as VCR, DVD or Camcorder.
Connect to TV Antenna : Connect an antenna(or CATV cable) to the antenna terminal on the back of the monitor.
1. Product Specification Monitor Type TFT LCD Flat Panel Resolution / Color 1024 x 768 (XGA) Display Colors 16.7M Pixel Type RGB stripe arrangement Pixel pitch 0.3mm(H) x 0.3 mm(V) Viewable Screen Size 15.1 " Viewing Angles(H/V) 130/110 Video Input Analog / R.G.B., 0.7 Vp-p Contrast Ratio 400 :1 Brightness 250 cd/m² AC/DC Adapter? Adapter 100-240V, 50 ~ 60 Hz , DC 12V / 3.
2. Product's Display Specification REFRESH HORIZONTAL PIXEL RATE FREQUENCY FREQUENCY 640 X 350 70 Hz 31.5 KHz 25.175 MHz VESA Standard 640 X 400 70 Hz 31.5 KHz 25.175 MHz VESA Standard 720 X 350 70 Hz 31.5 KHz 28.35 MHz VESA Standard 60 Hz 31.5 KHz 25.175 MHz Indurstry Standard 72 Hz 37.9 KHz 31.500 MHz VESA Standard 75 Hz 37.5 KHz 31.500 MHz VESA Standard 56 Hz 35.1 KHz 36.600 MHz VESA Guidelines 60 Hz 37.9 KHz 40.000 MHz VESA Guidelines 72 Hz 48.1 KHz 50.
The front part of panel of this model consists of following function buttons. Description for each of function button is shown below. Select Button 1. Displays a OSD of all of the available input source. (PC / TV / VIDEO 1 / VIDEO 2). 2. Exit the active the OSD PIP(Picture in Picture) Button (171P1 / 171P2 : Remote Control) Activates PIP(Picture-in-Picture) window directly in PC mode. Selects video sources(Video/S-VHS/TV) Auto Button Allows the monitor to self-adjust to the incoming video signal.
1. OSD Adjustment - Set OSD value with the Instructions described below.
3) Adjustment procedure for VIDEO 1 / 2 Monitor Mode
2. Frequently used functions 1) Monitor Self-Adjust - Allows the monitor to self-adjust to the incoming video signal. Press the AUTO Button. 2) Adjust Speaker volume - Increases or decreases the level of speaker volume. Press the buttons. 3) Adjust PIP(Picture in Picture) - Activates PIP(Picture-in-Picture) window directly in PC mode.
1. Menus when using PC Mode 1) PICTURE Brightness : Adjust to brighten or darken the picture. Contrast : The contrast control determines the white level of the picture. H-Position : Move the entire screen to the left or right. V-Position : Move the entire screen to the below or upper. PHASE : Fine tuning of the screen even though it is not easily distinguishable with naked eyes. CLOCK : Adjust the horizontal-size(size of horizontal screen)of the entire screen.
OSD POS : Adjust the position of OSD screen to 9 positions designated in the window screen. OSD H-POS : you can change the horizontal position where the OSD menu appears on your monitor OSD V-POS : You can change the vertical position where the OSD menu appears on your monitor OSD TIMEOUT : The OSD will automatically turn off if no adjustments are made for a certain time period. OSD BACKGROUND : Changes the transparent(or opaque) status of the background of the OSD.
2. Menus when using TV Mode 1) Picture Brightness : Adjust to brighten or darken the picture. Contrast : The contrast control determines the white level of the picture. Color : Adjust to increase or decrease color intensity.. Tint : Change the tone of the color. Image : Adjust the sharpen or soften the picture. SCALING : Resize the input screen image and display. (nomal, zoom, anamorphic, zoom 2, wide - Resizing) 2) Advanced Sharpness : Adjust the sharpen or soften the picture.
Tune option : Manually or automatically performs tune in. (Fine tuning in case of manual) Fine Tune : Due to weak signals or a wrong antenna configuration, some of the channels may not be tuned correctly. With fine tune function, you can tune in each channel precisely which has a grainy picture. Channel edit : You can exclude the channels of your choice from the channel scan operation. Channel search : Searches available channels and stores all automatically. Channel swap : Change the current channel .
3. Menus when using VIDEO 1(Composite) / VIDEO 2 (S-VHS) Mode 1) Picture Brightness : Adjust to brighten or darken the picture. Contrast : The contrast control determines the white level of the picture. Color : Adjust to increase or decrease color intensity.. Tint : Change the tone of the color. Image : Adjust the sharpen or soften the picture. SCALING : Resize the input screen image and display.
(TV Only-Option)
1. SELECT Button : Displays a menu of all of the available input source. (PC / TV / VIDEO 1 / VIDEO 2). 2. CHANNEL UP/DOWN Buttons : Press to select channels or menu settings. 3. PC Select Button : PC Select. 4. Number buttons : Press to directly select channels. 5. AUTO Button : Self-Adjust to the incoming video signal. 6. ZOOM IN/OUT Button : adjust the Screen size using ZOOM button 7. PIP Button : Activates PIP(Picture-in-Picture) window directly in PC mode. 8. MUTE Button : Switches the sound on or off.
In case of trouble, check these before calling the service center. What you see... Suggested Actions Screen is black and power Ensure that the power cord is firmly connected and the Monitor is on. indicator is off Screen is black and power Ensure that the signal cable is firmly connected to the PC or video sources. indicator is blinks. Ensure that the PC or video sources are turned on. Screen position and size is Press the AUTO Button. incorrect.
Dot pitch The image on a monitor is composed of red, green and blue dots. The closer the dots, the higher the resolution. The distance between two dots of the same color is called the 'Dot Pitch'. Horizontal Frequency The time to scan one line connecting the right edge to the left edge of the screen horizontally is called Horizontal Cycle. The inverse number of the Horizontal Cycle is called Horizontal Frequency.
1. Separation 1) Turn off your monitor and unplug its power cord. 2) Lay the Monitor face-down ward on a flat surface with a cushion beneath it to protect the screen. 3) Remove the screws( A ) and then remove the Mounting Device from the monitor. 2. Union 1) Align the Mounting Device with the holes( B ) in the Rear Cover and secure it with the screws.
