This equipment has been designed for the normal use. It is certified to comply with Electron Wave Suitable Registration. The user this equipment in everywhere including residential areas. 171T USER GUIDE Notice This equipment is one of first class quality. The LCD Panel is composed of more than 2 Million pixels and may have some faulty pixels. LCD panels with a maximum of 10 faulty pixels are classified as products of good quality. This standard is accepted by other manufacturers of LCD panels.
INFORMATION TO THE USER (Part 15.105(b)) INFORMATION TO THE USER This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
Please observe all following rules for installation, usage, and services so as to not defeat the safeguards incorporated into this monitor. Safety precautions are divided into Warning and Attention. Warning : Please ensure that no water leaks or gets onto or into the LCD monitor. Accidental exposure to water may cause fire or electrical damage. If case occurs, please turn off and unplug the monitor. If there is smoke or abnormal noises, please contact the store or customer service center.
Provide a secure connection to the power supply and do not use damaged power cords or plugs. Electrical shock or fire hazard may result. Do not place the monitor in exposed places or near water. Do not clean the monitor with water or touch it with wet hands. -Electrical shock or fire hazard may result. During lightening storms, unplug the monitor from the wall outlet and do not touch it.
Not using the monitor for hours, unplug the monitor from the wall outlet. - Dust may cause heat, fire, shock or short circuit If you use an outdoor antenna, be ensure that no water leaks through connectors and get onto the monitor. - Any liquid spill on the TV may cause fire or electric shock In case of any smoke or abnormal noise, immediately stop use of product and pull the power cord from the wall outlet. Then call your local dealer or service representative for assistance.
Install the monitor in stable place. - An unstable monitor may crash or fall. Personal injury, damage, or malfunction may result. Do not block ventilation openings with any curtain or tablecloths. - The increase of inside temperature may cause fire DO not drop the unit or make any scratch on the panel when you move the product. -Any scratch on the panel or drop of the product may cause functional failure. When moving the monitor, turn it off and disconnect all cables and the plug.
When disconnecting from the wall outlet, grab the plug. - Grabbing the cord may result in heat generation or fire hazard. Keep your eyes 20 inch away from the screen and 0~15° down in relation to the screen. - Viewing at too close a position and wrong posture can weaken your eyes. Do not press hard with your finger or scratch with sharp object on the surface of the LCD. -Any damage on the surface of the LCD may cause functional failure.
If you install outdoor antenna, be sure to install it at the distance from power wire. - If the antenna contacts with the power wire, it may cause electric shock. Be sure to keep the distance of the outdoors antenna so that it would not touch electric wire in case it falls by heavy wind. - If the antenna touches electric wire, it may cause injury and electric shock.
1. Adjust Buttons : Moves the selector up or down on the OSD. Increases or decreases the channel number. 2. Volume Buttons : Adjusts OSD Settings. Increases or decreases the level of speaker volume. 3. Auto Button : Automatically adjusts the monitor settings on PC mode. 4. Select Button : Selects the input source. (PC / TV / AV1 / AV2). 5. Menu Button : Opens or Closes the OSD. 6. Power Button : Turns ON/OFF the LCD TV/Monitor.
1. Power In Terminal Connect the DC plug of the AC-DC adaptor to the 12V power in terminal of the set. 2. D-SUB Terminal Connect the monitor D-SUB connector and the PC using the D-SUB signal cable. 3. S-Video Input Connect S-Video cable to this input. 4. Composite Video Input Connect video cable to this input. 5. Audio Input (Left) Connect left audio cable to this input. 6. Audio Input (Right) Connect right audio to this input. 7. PC Audio Input Connect the audio output of the PC. 8.
Please make sure the following items are included with your monitor. If any items are missing, contact your dealer.
Attention : Power off your LCD TV/Monitor before making any connections. 1. Power Connection : Connect the DC Adaptor to the power port on the back of the monitor 2. Connection of PC : Connect the signal cable from the monitor output socket of the PC to D-SUB terminal of the set. 3. AUDIO IN : Connect the AUDIO IN on the rear of the LCD TV/Monitor and the AUDIO OUT of the PC using the audio cable.
1. Connecting VIDEO 1 1. Connect RCA cable(Yellow) to an appropriate external A/V device such as VCR, DVD or Camcorder. 2. Connect RCA audio cables to "STEREO (R)" and "Audios (L)" terminals and the other ends to corresponding audio out terminals on the A/V device.
2. Connecting VIDEO 2 1. Connect S-VHS cable to an appropriate external A/V device such as VCR, DVD or Camcorder.
Connect to TV Antenna : Connect an antenna or CATV cable to the antenna terminal on the back of the monitor.
1. Product Specification 337.92mm(H) x 270.
This specification of this product might be changed without any notice. 2. Product's Display Specification HORIZONTAL VERTICAL FREQUENCY FREQUENCY (KHz) (Hz) 640 X 350 31.500 70.0 640 X 350@70Hz - Dos Graphic Mode 640 X 480 31.500 60.0 640 X 480@60Hz - Industry Standard 640 X 480 35.014 66.7 640 X 480@66.6Hz - Mac Mode 640 X 480 37.860 72.8 640 X 480@72Hz - VESA Standard 640 X 480 37.500 75.0 640 X 480@75Hz - VESA Standard 720 X 400 31.545 70.
The front part of panel of this model consists of following function buttons. Description for each of function button is shown below. Select Button Displays a menu of all of the available input source. (PC / TV / AV1 / AV2). Auto Button Self adjusts the monitor settings on PC mode. Menu Button Opens or Closes the OSD. Power Button Turns ON/OFF the LCD TV/Monitor. Adjust Buttons( , ) Moves the selector up or down on the OSD. Increases or decreases the channel number.
1. OSD Adjustment - Set OSD value with the instructions described below.
3) Adjustment procedure for AV 1 / 2 Mode 2. Frequently used function 1) LCD TV/Monitor Auto adjustment function. - Automatically adjusts the monitor settings on PC mode.
Press the AUTO Button. 2) Adjust Speaker volume - Increases or decreases the level of speaker volume. Press the buttons. 3) Reset Factory Default - Screen parameters are replaced with the factory default values. 4) Select Country (TV function) - Select a channel system that is being used in your region.
5) Auto Setup (TV function) - The LCD TV/Monitor will scan the channels and memorize all of the channels it can receive. 5) Fine Tune (TV function) - Due to weak signals or a wrong antenna configuration, some of the channels may not be tuned correctly. With fine tune function, you can tune in each channel precisely which has a grainy picture.
6) Antenna Input (TV function) - Selects the desired source, between AIR and CABLE.
1. Menus when using PC Mode 1) PC ADJUST Brightness : Adjust the brightness of video or TV without affecting PC RGB's brightness. Contrast : Adjust the contrast of video or TV without affecting PC RGB's contrast. H-Position : Move the entire screen to the left or right. V-Position : Move the entire screen to the below or upper. PHASE : Fine tuning of the screen even though it is not easily distinguishable with naked eyes. CLOCK : Adjust the horizontal-size(size of horizontal screen)of the entire screen.
2. Menus when using TV Mode 1) PICTURE Brightness : Adjust the brightness of video or TV without affecting PC RGB's brightness. Contrast : Adjust the contrast of video or TV without affecting PC RGB's contrast. Sharpness : Adjust the sharpness of video or TV image. Color : Change the richness of color. Tint : Change the tone of the color. Smart Picture Control : Changes the picture setting that is defined for [NORMAL], [ DYNAMIC], [ CINEMA] or [ USER] each.
Sharpness : Adjust the sharpness of video or TV image. Color : Change the richness of color. Tint : Change the tone of the color. Smart Picture Control : Changes the picture setting that is defined for [NORMAL], [ DYNAMIC], [ CINEMA] or [ USER] each.
(TV Only-Option) 1. SELECT Button : Displays a menu of all of the available input source. (PC / TV / AV1 / AV2). 2. Number buttons : Press to directly select channels. 3. TV/CATV Select Button : Press to convert reception modes between aerial and CATV. 4. VOLUME UP/DOWN Buttons : Adjusts the sound level. Adjusts menu settings. 5. EXIT Botton : To exit from the OSD 6. SLEEP Button : To select the length of time before the set automatically, switches to standby. 7.
9. SPC (Smart Picture Controls) Button : To access preset video settings (NORMAL, DYNAMIC, CINEMA, and USER) 10. MENU Button : To display or exit from the OSD. 11. MUTE Button : Switches the sound on or off. 12. CHANNEL UP/DOWN Buttons : Press to select channels or menu settings. 13. ADD/ERASE Button : Press to add and erase channels on your LCD TV.
In case of trouble, check these before calling the service center. What you see... Suggested Actions Screen is black and power Ensure that the power cord is firmly connected and the LCD TV/Monitor is on. indicator is off Screen is black and power Ensure that the signal cable is firmly connected to the PC or video sources. indicator is blinks. Ensure that the PC or video sources are turned on. Screen position and size is Press the AUTO Button. incorrect.
Dot pitch The image on a monitor is composed of red, green and blue dots. The colser the dots, the higher the resolution. The distance between two dots of the same color is called the 'Dot Pitch'. Horizontal Frequency The time to scan one line connecting the right edge to the left edge of the screen horizontally is called Horizontal Cycle. The inverse number of the Horizontal Cycle is called Horizontal Frequency.
1. Separation 1. Turn off your monitor and unplug its power cord. 2. Lay the LCD Monitor face-down ward on a flat surface with a cushion beneath it to protect the screen. 3. Remove the screws( A ) and then remove the Stand from the LCD monitor. 2. Union 1. Align the stand with the holes( B ) in the Rear Cover and secure it with the screws.
