WINDOW CLEANING ROBOT Official app Download Product calibration video Track wipe video Product operation video
1.Safety Criteria CONTENTS 1. Safety Criteria 2 Please read this manual carefully before using the product. Save the manual. 2. Product Composition 5 When using the product, please maintain consistent vigilance and keep 2.1 Package contents 5 the following precautions: 2.2 Technical parameters 5 6 3. Product Manual 7 3.1 Precautions before use 7 3.2 Install the cleaning cloth 8 3.3 Connect the adapter 9 3.4 Assemble the safety rope assembly 9 3.5 Product work 10 3.
1.Safety Criteria outlet. Do not use the product when it is not working properly due to dropping, damaging or water ingress. To avoid injury, the product should be repaired by the manufacturer or its after-sales service department. 1.14 The cleaning cloth can be applied to the wet glass surface, Nonreflux of water droplets on glass. When the flow of water on the glass is left, it is strictly prohibited to use this product. 2.The following conditions should be noted when using this product: 2.
2. Product Composition 2. Product Composition 2.3 Part name 2.1 Package Contents Host Adapter Components Host Safety Rope Components Remote Control Instruction Manual 1. Start/Pause 2. Handle 3. Power Switch/Safety Lock 4. Supply Hub 5. Movable chassis 6. Guide Roller 7. Anti-falling Sensor 8. Driving wheel 9. Suction Sensor 10. Air Inlet 11. Area 1 for Cleaning Cloth 12. Area 2 for Cleaning Cloth Cleaning Cloth 2.
3. Product Manual 3. Product Manual 3.1 Precautions before use When the product is working on a horizontal glass surface, the remote control should be used to control the operation of the product. If you use this product on windows that are not completely vertical, the product may not work normally. Make sure that you are in the side care area and, if necessary, assist the product.
3. Product Manual 3. Product Manual 3.3 Connect the adapter 3.5 Product work 1 Connect the power supply Disassemble the power line end of the product and the power line of the adapter, connect both ends of the extension line to the power line end of the product's power supply line and the adapter power line, and tighten up the power line at the end of the power supply line and the adapter. and make sure the machine is locked by the metal locking.
3. Product Manual 3. Product Manual 3 Secure placement Make sure the product is in the normal operating state, place it on the glass surface, make sure the product is completely adsorbed on the glass, then release the handle. Glass Rail Z Mode: Start the work by the remote control mode key Z key: for horizontal glass, the product to "Z" route to work. If there is an immovable obstacle (such as a guard rail, furniture, etc.
3. Product Manual In the case of pause, the direction of the product can be controlled by the direction key on the remote control, and the work route of the product can be switched. ( machine no longer memorize the precious route) 3. Product Manual 2 Power off Open the lower cover and turn off the power switch. I 3 Disconnect power Remove the safety clip and disconnect the power supply. 3.7 End the work End glass cleaning, the product will return to the start position, the beep sounds.
4. Maintenance 4. Maintenance 4.1 Cleaning cloth Remove the cleaning cloth, soak in water at 20℃ for 2 minutes, then with a soft brush clean . Walking belt: Clean with a dry cloth so as not to damage the product suction. Do not rub or wring dry, dry naturally before use. 4.2 Bottom components Fan: Clean with a dry cloth so as not to damage the product suction. Fall prevention sensor: Clean with a dry cloth to maintain its sensitivity.
7. Fault Description 7. Fault Description Troubleshooting Solution: Number 1 2 3 4 Machine walking is laborious, not smooth Solution Wipe the track or replace other wipes according to the way of track wiping. Use the up and down keys to keep the machine away from the edge of the clamp.After the machine is out of trouble,restart,do not adjust the direction at the edge. The error of pressing the calibration key of the remote The machine can't control in machine running is caused.
8. Warranty Card Warranty Card Dear client! Thanks for using product. In order to offer perfect after sale service, our service team would like to give you promise for standard service hereby. Please keep well your valid document of purchasing as an evidence to get our after sale service. Product Quality Assurance Description: 1. Warranty time: start from purchasing date, 12 months for main body. 2.