User's Manual
Table Of Contents
- Document History
- Revision History
- GENERAL SAFETY PRECAUTIONS
- TABLE OF CONTENTS
- LIST OF FIGURES
- LIST OF TABLES
- Introduction
- Figure 1Block Diagram of Host Unit
- Figure 2 Block Diagram of Remote Node
- Safety
- System Overview and Unit Description
- Figure 3mBSC System Functional Overview
- Figure 4 Host Unit
- Figure 5BIU
- Figure 6FIU
- Figure 7 PSU
- Figure 8RCU
- Table 1 Host Unit User Interface
- Front Panel
- Rear Panel
- Figure 10Fiber BCM Enclosure Outline
- Figure 11Fiber BCM Interior Layout
- Table 3BCM Enclosure User Interface
- Figure 12BCM Enclosure User Interface
- Table 4 Single-band RUM Enclosure User Interface
- Figure 14 Single-band RU Enclosure User Interface
- Table 5 Indicator Description
- Table 9Fiber RTM Enclosure User Interface
- Table 10 Indicator Description
- System Installation
- Figure 20 Mounting Brackets for 19” Rack Installation
- Figure 21Host Unit-19” Rack Mounting View
- Figure 22Host Unit Grounding Stud
- Figure 23 Grounded Host Unit
- Figure 24 BTS QMA Coaxial Cable Connection
- Figure 26E2000 Fiber Optic Port on Host Unit FIU
- Figure 27 48VDC Host Power Connection
- Figure 28IP Connection for local GUI Control
- Figure 29Modem Port on RCU (DB9 male)
- Figure 32 Fiber Optic Cable Connection to RTM Enclosure
- Figure 33 RPM
- Figure 36 Flow Chart of System Debugging
- System Monitoring &Configuration
- Figure 37– EMS Local GUI Login
- Figure 38- Main Page Expanded Topology
- Figure 39- Main Page Summary View
- Figure 40- RCU Component View
- Figure 41- Main Page Equipment Status
- Figure 42- FIU Optical Power Levels
- Figure 43- RTM Optical Power Levels
- Table 16System Alarms
- Maintenance
- Figure 53Host Unit Trouble Shooting
- Figure 54Remote Unit Trouble Shooting
- Terms, Acronyms & Abbreviations
- Packing List
- IC Radiation Exposure Statement
- IC Déclaration sur la radio exposition
mBSC-CM RUM
mBSC-CM December 15, 2015
Page 16
3.3.2.1.1 Multi-Carrier Power Amplifier (MCPA) Modules
The MCPA Module is the heart of the mBSC RUM Enclosure. The MCPA Module boosts the BTS forward
link transmission signal. Operating on28VDC input, the MCPA Module produces 5W composite RF power
for each band (measured at output of the antenna combiner).
The mBSC system provides linear amplification of multi-carrier, mixed-mode signals in the 700MHz,
850MHz, 1900MHz, 2100MHz and 2600MHz frequency bands with the respective RU’s.
3.3.2.1.2 Duplexer
The duplexer is used to make the bi-directional signals into simplex signals and provides sufficient isolation
3.3.2.1.3 CPU(Central Processing Unite）
The CPU provides communications and monitors with power amplifier module or other functional module.
3.3.2.2 Mounting
The single-band RUM enclosure is plug in REMOTE NODE multi-slot chassis.
3.3.2.3 RF Connection
The RF signal connections with the single-band enclosure are supported through two QMA female coaxial
connectors and one N female connector. The two QMA female connectors are used for coaxial cable
connection (RF jumper) of the Tx and Rx RF signals between the RTM enclosure and the single-band RUM
enclosure. The N female connector is used for coaxial cable connection of the amplified duplex Tx/Rx RF
signal to the BCM enclosure.
3.3.2.4 Cooling
The single-band RUM enclosure is cooled by cooling fans in the bottom of the casing. A minimum of 200mm
(7.87 inches) of clearance space must be provided on both the top and the bottom sides of the Remote
Node for air convection.