/ 8 PDBU-31119-X000-A0 User’s manual of 802.11n miniPCI BUFFALO INC. Broadband Solutions Business Unit Product Name: 802.11n Wireless miniPCI Product Number: WZR-G300N Document Number: PDBU-31119-X000-A0 Rev. Date Description of change Prepared by A0 2006/04/19 first edition Nakazono (YKK-013-04) BUFFALO I NC.
/ 8 PDBU-31119-X000-A0 Table of Contents 1. Introduction 2. System block diagram 3. Product Spec 3-1. System Configration 3-2. Basic Spec 4. Outline Dimension 5. Manufacturing Test 5-1. Instruction 5-2. Test Configration 5-3. Test Flow and Criteria 6. Assembly and Label information 6-1. Instruction 6-2. Assembly drawing 6-3. Label Drawing 7. Packaging and Shipment 7-1. Instruction 7-2. Packing drawing 7-3. Shipment method 8. Restrictions about production 8-1.
/ 8 PDBU-31119-X000-A0 1. Introduction This document describes the design specifications of 802.11n Wireless miniPCI. This product guarantees compatibility with IEEE 802.11n draft compliant goods. And this product is compatible with IEEE802.11b/g legacy goods. 2. System block diagram WZR- G300N BLOCK DIAGRAM Dipole Antenna Antenna Switch TX PA Dipole Antenna Transceiver (2055) Antenna Switch Antenna Switch MAC, B/ B (4321) TX PA Dipole Antenna Power Supply Regulator +2.5V PCI bus +1.8V +3.
/ 8 PDBU-31119-X000-A0 3. Product Spec 3-1. System Configration ITEM Contents Interface / System bus support PCI IEEE 802.11g、802.11b Standard Data rete (Mbps) 54,48,36,24,18,12,9,6,11,5.5,2,1 20MHz BW: 130,117,104,78,52,39,26,13 40MHz BW: 270,243,216,162,108,81,54,27 Modulation PSK/CCK,DQPSK,DBPSK,OFDM Network architectures Infrastructure and ad hoc Operating channels 2.4GHz: 11 for North America, 13 for Europe, and 14 for Japan RF Output Power 2x2: 2.4GHz 11n 15 dBm 2x2: 2.
/ 8 PDBU-31119-X000-A0 4. Outline Dimension BUFFALO I NC.
/ 8 PDBU-31119-X000-A0 5. Manufacturing Test The production company must report test result of wireless to BUFFALO in production test. It must show that a produced product satisfies TELEC standard. 5-1. Instruction 5-2. Test Configration 5-3. Test Flow and Criteria 6. Assembly and Label information 6-1. Instruction 6-2.Assembly drawing 6-3.Label Drawing 7. Packaging and Shipment 7-1. Instruction 7-2. Packing drawing 7-3. Shipment method 8. Restrictions about production 8-1.
/ 8 PDBU-31119-X000-A0 9. Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
/ 8 PDBU-31119-X000-A0 This device is intended only for OEM integrators under the following conditions: 1) The antenna must be installed such that 20 cm is maintained between the antenna and users, and 2) The transmitter module may not be co-located with any other transmitter or antenna. As long as 2 conditions above are met, further transmitter test will not be required.