Quick Start Guide

16 ULTRABASS BXD15A/BXD15/BXD12A/BXD12 Quick Start Guide 17
(13)(11) (12)(9) (10)(1) (2) (3) (4) (5) (6) (14)(7) (8)
(15) (16) (17) (18) (19) (20) (21)
ULTRABASS BXD15A/BXD15/BXD12A/BXD12 Controls
(EN)
Step 2: Controls
(1) INPUT jack is used to connect your
instrument’s cable with a ¼" TS plug.
(2) MUTE button mutes the output of the
ampli er for silent tuning or for switching
instruments. The CLIP LED ring around
the button lights up to indicate clipping
at the INPUT jack. If the CLIP LED lights up
consistently, press the -15 dB button to reduce
the gain at the INPUT jack.
(3) -15 dB button reduces the INPUT jack’s
sensitivity by 15 decibels for use with
active pickups. Press this button if the CLIP
LED consistently lights up to indicate that
the instrument signal is overloading the
preamp circuit.
(4) GAIN knob sets the signal level going into the
amplier’s preamp section.
(5) COMP button activates the internal
compressor when pressed. Use the
compressor to even out and control dynamics
in your signal for a more consistent sound.
The THRESH LED lights up when the
compressor is active and ickers when the
input signal reaches the compressor threshold
set by the COMP knob.
(6) COMP knob controls the amount of
compression applied by the internal
compressor. Rotate the knob clockwise for a
more compressed sound. When the knob is set
fully counter-clockwise, no compression will
be applied.
(7) ULTRA LOW button boosts the extreme low
end of your sound when pressed. Press the
ULTRA LOW button to add body and thickness
to your instrument’s tone.
(8) BASS knob controls the bass frequencies of
your sound. Rotate the knob counterclockwise
to cut bass frequencies or clockwise to boost
bass frequencies.
(9) MID knob boosts or cuts the midrange
frequencies controlled by the MID FREQ
knob. Rotate the knob counterclockwise
to cut the designated mid-range
frequencies or clockwise to boost those
mid-range frequencies.
(10) MID FREQ knob sets the mid-range frequency
to be boosted or cut by the MID knob.
(11) TREBLE knob controls the treble
frequencies of your sound. Rotate the knob
counterclockwise to cut treble frequencies or
clockwise to boost treble frequencies.
(12) ULTRA HIGH boosts the high frequencies of
your sound when pressed. Press the ULTRA
HIGH to boost harmonics and add denition to
your instrument’s sound.
(13) MASTER knob controls the nal output
volume of the amplier. Rotate the knob
counter-clockwise to reduce volume and
clockwise to increase the volume.
(14) POWER switch turns the unit on and o.
Always make sure the POWER switch is in the
“O ” position when initially connecting the
unit to the mains power connection.
(15) POWER SOURCE accepts the included IEC
power cable.
(16) VENTILATION FAN prevents the unit from
overheating. The ventilation opening should
not be blocked during operation.
(17) DI OUT can be used to connect the unit
directly to a mixer or PA system using a
balanced XLR connection.
(18) TUNER OUT sends out an unbalanced signal
suitable for use with electronic tuners.
(19) FX INSERT SEND/RETURN creates a bu
ered serial loop for use with eects pedals or
rackmount eects processors.
(20) AUX IN accepts line-level signals from
MP3 players or other sound sources using
RCA connectors.
(21) FOOTSW connection allows you to control the
MUTE and FX INSERT eects loop functions
remotely by using a dual footswitch with
a ¼" TRS connector (FSB102B footswitch
not included).