inland Model 1500 For serial number 08BM1500001 and later Operator’s and Parts Manual Bale Carrier 46912 04/08
INLAND WARRANTY POLICY Buhler Manufacturing products are warranted for a period of twelve (12) months (90 days for commercial application) from original date of purchase, by original purchaser, to be free from defects in material and workmanship under correct, normal agricultural use and proper applications.
bühler 1500 Bale Carrier OPERATORS AND PARTS MANUAL Table of Contents Description TERMINOLOGY AND DECAL LOCATIONS ILLUSTRATIONS……..………... GENERAL SPECIFICATIONS…..………………………………………………… INTRODUCTION……………………………………………………………………. Serial Decal Location……………………………………………………………. Warranty Registration……………………………………………………………. SAFETY……………………………………………………………………………… General Safety Notes……………………………………………………………. Safety Decals…………………………………………………………………….. Important Precautions…………………………………………………………… PRE OPERATION CHECKLIST...
16 YELLOW RED RED 15 15 16 YELLOW 18 1500 2 16 15 10 12. Part # 814490 12 Slow Moving Vehicle RED 7 YELLOW 13. Part # 814457 13 AMBER REFLECTOR Carrier Beam Note: 1) Refer to page 7 for detailed information on safety decals. 2) Awarness signs are shown on one side only for clarification. Signs are provided on both left and right sides except for numbers 1, 2, 5, 6, 8, 9 and14 which are only on the position indicated.
bühler 1500 Bale Carrier GENERAL SPECIFICATIONS: Dimensions: - Length: 44’ (13.4 m) - Deck Length: 37’ (11.3 m) - Width: 8’6” (2.6 m) - Weight (empty): 5495 LB (2498 kg) - Drawbar Vertical Load (empty): 1365 LBF (6071 N) - GVW: 18720 LB (8491 kg) Capacity: - Total bale payload: 13225 LB (6000 kg) - Bales 6’ (1.8 m) diameter maximum to 4’ (1.2 m) diameter minimum - Hay crop, small grains, and flax straw - Eight 4’ (1.2 m) wide bales - Seven 5’ (1.52 m) wide bales Tires: - 4-12.
bühler 1500 Bale Carrier INTRODUCTION CAUTION: Your 1500 Bale Carrier requires a recommended minimum 60 hp (75kw) tractor. The maximum loaded transportation speed of 20 mph (32 km/h) and 18720 LB (8491 kg) must not be exceeded. This manual has been provided as information regarding the specifications, safe operation and maintenance of your agricultural 1500 Bale Carrier. Read and understand this manual and the tractor manual prior to operating to obtain the best use of operating your 1500 Bale Carrier.
bühler 1500 Bale Carrier SAFETY Read and understand all the safety messages listed in this manual. For your safety and the safety of others near the machine, learn how to control and operate your 1500 Bale Carrier properly. It is your responsibility to inform subsequent operators and owners of these precautions. General Safety Notes Keep young children away from machinery and bales at all times. Be aware that accidents often happen when the operator is tired or in a hurry to get finished.
bühler 1500 Bale Carrier Never leave the tractor unattended while the 1500 Bale Carrier is hooked up, always shut tractor off and remove key before leaving the tractor seat. A child or even a pet could engage an idling machine. Keep the 1500 Bale Carrier on solid ground; rocks and holes can be dangerous for operation and movement. Prior to use, check to ensure the attachment is properly hitched. Improper use of the 1500 Bale Carrier and tractor can cause serious injury or death.
bühler 1500 Bale Carrier Safety Decals The terminology and decal location illustration shows the approximate location and detail of safety decals. To install safety decals ensure the installation area is clean and dry. Decide on the exact position before you remove the backing paper. Remove the smallest portion of the split backing paper and align over the specified area. Carefully press in place. Slowly peel back the remaining paper and smooth the remaining portion in place.
bühler 1500 Bale Carrier Important Precautions The alert symbol is used throughout this manual. It indicates attention is required and identifies hazards and alerts you that your safety is involved. Follow the recommended precautions. CAUTION Indicates a potentially hazardous situation, which may result in injury. It may also be used to alert against unsafe practices.
bühler 1500 Bale Carrier PRE-OPERATION CHECKLIST CAUTION Make sure the tractor has a 60 hp (45 kw) or greater rating and a mass of 12480 LB (5660 kg). Make sure the drawbar is capable of supporting the 1500 Bale Carrier empty or loaded. WARNING The tractor must be equipped with an approved Roll over Protection Structure (ROPS) and safety belts to help prevent personal injury or death caused by tractor roll over.
bühler 1500 Bale Carrier OPERATION CAUTION Prior to operation ensure the operator has read and understands the safety requirements of the 1500 Bale Carrier. Ensure the pre-operation checks have been completed prior to operation. 1. Attaching Bale Carrier To Tractor CAUTION Shut off tractor, engage parking brake and remove key before working around 1500 Bale Carrier. Refer to tractor manual for tractor parking procedures. CAUTION Use only the drawbar to couple the 1500 Bale Carrier to the tractor.
bühler 1500 Bale Carrier The power required to operate the 1500 Bale Carrier is supplied by the tractors 12-volt electrical system. Connect the red wire to the tractor positive and green to tractor ground. Connection may be made via tractor accessory plug or alternate method. The 15-amp fuse must be used on the positive wire as supplied. Verify 1500 Bale Carrier operation matches 1500 Bale Carrier control handle decal.
bühler 1500 Bale Carrier 3. Carrier Control Operation To start 1500 Bale Carrier operation, engage the remote hydraulic valve in the extension position. Lock valve in detent. Valve to remain constantly on during operation. The control handle is fitted with one rocker switch and two momentary contact rocker switches. They function as follows: o PUSHER SPEED: Select (HIGH) to operate pusher motors in series at high speed or (LOW) to operate in parallel at low speed.
bühler 1500 Bale Carrier The Fixed Pick Up Arm requires the operator to drive at 90° to the bale direction. The bales are loaded “End On”. The bale is loaded onto the carrier deck by depressing and holding LIFT ARM UP until the bale rolls off the pickup arm and onto the carrier beams. The Bale Deflector attached to the fixed pick up arm allows the bales to be picked up from either “End On” or “Side On.” The deflector rotates the bale 90° before it is lifted up onto the carrier.
bühler 1500 Bale Carrier 5. Bale Pusher Operation CAUTION To avoid misbalanced loads the operator is only required to push back one bale length to prepare for the next bale. NOTE: Lower loading arm before operating the pusher. Depress and hold PUSHER BACK and move bales far enough to the rear to provide room to load the next bale. Return pusher all the way to the front by depressing and holding PUSHER FWD. Hi speed / Low torque mode is recommended for normal use.
bühler 1500 Bale Carrier 7. Unloading DANGER Make sure area is clear before unloading. Failure to do so could result in serious injury or death. NOTE: Do not run pusher all the way to the end, the resulting shock load may cause damage to chain and drive. Extend tilt cylinder to raise carrier beam by engaging the tractor’s extension hydraulics. Depress and hold the PUSHER BACK switch to push the bales off the carrier beam.
bühler 1500 Bale Carrier LUBRICATION CAUTION Place all controls in neutral, stop engine, set parking brake and remove ignition key before inspecting, servicing, adjusting or repairing the 1500 Bale Carrier. CAUTION Ensure the 1500 Bale Carrier tires and hitch are securely blocked. Otherwise, verify the 1500 Bale Carrier is properly coupled to the drawbar on a tractor with a minimum mass of 12480 LB (5660 kg).
bühler 1500 Bale Carrier MAINTENANCE CAUTION Place all controls in neutral, stop engine, set parking brake, remove ignition key and wait for all moving parts to stop before servicing, adjusting or repairing the 1500 Bale Carrier. CAUTION Ensure the 1500 Bale Carrier tires and hitch are securely blocked. Otherwise, verify the 1500 Bale Carrier is properly coupled to the drawbar on a tractor with a minimum mass of 12480 LB (5660 kg).
bühler 1500 Bale Carrier 2. Hydraulic System WARNING Escaping fluid under pressure can have sufficient force to penetrate the skin, causing serious personal injury. Before repairing, adjusting, or disconnecting lines, be sure to relieve all pressure. WARNING Never operate the 1500 Bale Carrier with frayed or damaged hoses or leaking fittings. A burst would cause the lift arm to drop suddenly and result in serious injury or death and cause damage to the loader or tractor.
bühler 1500 Bale Carrier 4. Chain Check for proper chain tension and sprocket alignment after first use and every 50 hours thereafter. Turn the front sprocket-adjusting bolt clockwise until there is approximately 6” (15 cm) of upward slack in the chain at the center of the track. Clockwise increases tension and counter clockwise reduces tension. Proper chain tension may be verified by raising the chain by hand. See lubrication section for further maintenance instructions. FRONT ADJUSTING BOLT 5.
bühler 1500 Bale Carrier 6. Storage CAUTION Place all controls in neutral, stop engine, set parking brake and remove ignition key before inspecting, servicing, adjusting or repairing the 1500 Bale Carrier. CAUTION Ensure the 1500 Bale Carrier tires and hitch are securely blocked. Otherwise, verify the 1500 Bale Carrier is properly coupled to the drawbar on a tractor with a minimum of 12480 LB (5660 kg). Start of Season Clean and inspect the bale carrier when taking it out of storage.
bühler 1500 Bale Carrier APPENDIX LIST Description Appendix Assembly Instructions…..……………………………………………………. A Hydraulic Assembly…………………………………………………………… B Electrical Assembly………..………………………………………………….. C General Assembly….…………………………………….…………………...
bühler 1500 Bale Carrier APPENDIX A Assembly Instructions Table of Contents Description Carrier Bundled Assembly………………………………………………………. Tandem Axle Assembly……………………………………………………… Brace Weldment……………………………………………………………... Taillight Assembly……………………………………………………………. Bale Retainer Weldment…………………………………………………….. Fixed Loading Arm………………………………………………………….. Bale Deflector Arm Assembly……………………………………………... RPU Assembly………………………………………………………………... Carrier Bundled Assembly Drawing…………………………………………….
bühler 1500 Bale Carrier CAUTION Make sure area is clear of obstructions, well lit, and has sufficient room for safe assembly. Do not work underneath raised assembly. CAUTION Ensure the carrier’s tires and hitch are securely blocked. Otherwise, verify the carrier is properly coupled to the drawbar on a tractor with a minimum of 12480 LB (5660 kg). Carrier Bundled Assembly 1.
bühler 1500 Bale Carrier 3. Taillight Assembly Refer to Carrier Bundled Assembly drawing: Remove and inspect all required hardware from parts box. Mount lights using fasteners supplied Connect the taillight wiring harnesses to their appropriate connections. Connect main lighting plug to tractor. Test by verifying correct lamps illuminate when signalling and braking. . 4. Bale Retainer Weldment Remove the hardware from parts box and transfer on to bale retainer weldment.
bühler 1500 Bale Carrier 6. Bale Deflector Arm Assembly Remove all hardware that is included with the deflector assembly. Remove the two top bolts from outer fork on lift arm. Maintain the spacing of the forks if already preset. If not, set spacing as described in the fixed pick up arm assembly section. Insert the coned end of the deflector onto the end of the outer fork. Align the bolt holes from the removed bolts on the outer fork and the end of the deflector attachment.
bühler 1500 Bale Carrier Align the lift cylinder rod and reinstall the pin. ADJUSTABLE FORK Adjust the outside bale fork to be positioned at the end of the lift arm and the inner bale fork 6” (15 cm) to 8” (20 cm) bigger than the BALE WIDTH + 6” TO 8” size of bale that is being loaded. Install the hydraulics according to the way the hydraulic assembly Appendix B calls for.
5 9 B B 14 17 17 20 27 6 3 8 BALE CARRIER ASSEMBLED 7 13 17 20 23 18 REAR VIEW OF BALESTOP PLACEMENT AS VIEWED FROM A A 13 17 20 12 19 1 6 BOLTS PER WHEEL 2 11 TO MAIN WIRING HARNESS 4 A BRACES USE SAME HARDWARE AS AXLE A UNDERSIDE VIEW OF TAILLIGHTS / WIRING HARNESS AS VIEWED FROM B B 10 YELLOW LENSE 21 12 19 24 15 16 19 25 bühler 1500 Bale Carrier Carrier Bundled Assembly
bühler 1500 Bale Carrier Carrier Bundled Assembly ITEM COMPONENT DESCRIPTION QTY PART NUMBER 1 B2400-14 AXLE ASSEMBLY 2 2 B2700-03 TIRE ASSEMBLY 4 3 C2407-00 TANDEM AXLE LOCATOR 2 4 C2907-00 SMV BRACKET & TAIL LIGHT MOUNT 1 5 C7035-00 REAR BRACE WELD'T 2 6 C7036-00 CENTER BRACE 2 7 C8005-00 AXLE 1 8 C8006-00 FRONT BRACE WELD'T 2 9 C8009-00 BALE RETAINER WELD'T-YELLOW 1 10 INE7045-00 LIGHT MOUNT BRACKET 1 11 813653 BOLT 0.563 NF X 1.
bühler 1500 Bale Carrier NOTE PAGE 29
bühler 1500 Bale Carrier APPENDIX B Hydraulic Assembly NOTE: 1) Hydraulic Assembly methods and layouts are common to the right and left sides. Only one side of each component is shown in this manual. 2) Seal Kits and Service Parts are only listed in the parts lists and are not indicated on the illustrations. Table of Contents Description Carrier Hydraulic Assembly Schematic (Standard Configuration). …………… Valve Bank Assembly………….….……………………………………….….... FPS Directional Valve Bank Assembly……………………………………...
TO TRACTOR COUPLER (RETRACT) TO TRACTOR COUPLER (EXTEND) TO TRACTOR COUPLER (RETRACT) TO TRACTOR COUPLER (EXTEND) bühler 1500 Bale Carrier Carrier Hydraulic Assembly Schematic (Part # A8000-04) Standard Configuration 31
bühler 1500 Bale Carrier Carrier Hydraulic Assembly (Part # A8000-04) Standard Configuration Item 1 2 3 4 5 6 7 8 9 10 11 Component Part # A8002-01 A7010-00 A7011-00 A8012-00 A8013-00 A7013-00 A8011-00 115001 812176 29105 886704 Description 1500 BALE CARRIER VALVE BANK ASSEMBLY HYD ASSY 1/2 X 130 RETURN LINE HYD ASSY 1/2 X 130 PRESSURE LINE TILT CYLINDER ASSY 3 X 10 PIN EYED TILT CYLI ASSY HYD 3/8 HOSE TILT ASSY LIFT ARM CYLINDER MOTOR MT ASSY 1500 BALE CARRIER 22.
bühler 1500 Bale Carrier ** Valve Bank Assembly (Part # A8002-01) (**) To be used only with OPEN-CENTER Configuration.
bühler 1500 Bale Carrier Valve Bank Assembly (Part # A8002-01) Item 1 2 3 4 5 6 7 8 9 10 11 Component Part # C8013-00 B7010-00 B8008-00 E2781-00 81549 812362 813667 811916 811414 812080 810582 Description VALVE BANK MOUNT WELDMENT SERIES/PARALLEL VALVE (2-SPEED) VALVE ASSY FPS DIRECTIONAL FLOW RESTRICTOR BOLT HEX 0.313NC X 0.75 GR5PL NUT LOCK (STEEL) 0.313NC GRBPL TEE RUN 1/2 MJIC X 3/4 MORB ELBOW 90 3/4 MORB X 9/16 MJIC ELBOW 90 3/4 MORB X 3/4 MJIC ADAPTOR STR 3/4 MORB X 3/4 MJIC BOLT HEX 0.313NC X 3.
bühler 1500 Bale Carrier FPS Directional Valve Assembly (Part # B8008-00) 5 2 1 2450 PSI PLUG FACING FORWARD 4 NOTE: THE SECOND ITEM 4 IS NOT VISIBLE BUT IS ON THE OPPOSITE SIDE IN THE POSITION OF THE OPEN HOLE IN THIS VIEW 3 B8008-00 FPS Valve Service Parts Item 1 2 3 4 5 6 Compone nt Part # 22208-01 22149 222083-03 812081 22208-02 X2684 Description MV4-17 SPOOL SECTION CROSS OVER RELIEF VALVE BALE CARRIER SET 2400 C07-12TD COIL PLUG 3/4 MORB STL MV4-A LOCK VALVE SEAL KIT VALVE BANK (ITEM NOT VI
bühler 1500 Bale Carrier Series/Parallel Valve Low and High Speed (Part # B7010-00) 2 1 B7010-00 Parallel Valve Service Parts Item 1 2 3 Component Part # 22083-03 22083-01 X2684 Description C07-12TD COIL SERIES/PARALLEL VALVE (LOW &HIGH SPEED) SEAL KIT VALVE BANK (ITEM NOT VISIBLE) 36 Qty 1 1 1
bühler 1500 Bale Carrier Hydraulic Return Line Assembly (Part # A7010-00) 1 3 2 5 4 Item 1 2 3 4 5 Component Part # 29170 812841 813119 813305 813666 Description HOSE 1/2 X 130 3/4 MORB X 3/4 MALE TIP 0.5 BODY 0.75 ORB ADAPTOR STR 3/4 MORB X 3/4 MORB DUST CAP 0.
bühler 1500 Bale Carrier Hydraulic Pressure Line Assembly (Part # A7011-00) 1 2 3 Item 1 2 3 Component Part # 29170 812841 813305 Description HOSE 1/2 X 130 3/4 MORB X 3/4 MALE TIP 0.5 BODY 0.75 ORB DUST CAP 0.
bühler 1500 Bale Carrier Carrier Tilt Cylinder Assembly (Part # A8012-00) 1 2 Item 1 2 Component Part # 813640 24895 Description Qty ELBOW 90 9/16 MORB ADJ 9/16 MJIC CYLINDER 3.0 DIA X 10 PIN EYED W / RESTRICTOR 2 1 24895 Cylinder 3.0 Diameter Service Parts Component Part # 812655 X2353 24899 115288 24897 Description LOCKNUT 0.875 NF SEAL KIT FOR ITEM 24895 TUBE WELDMENT 3.0 DIA SHAFT WELDMENT 1.25 X 16.75 LG HEADPLATE 3.0 X 1.
bühler 1500 Bale Carrier Carrier Tilt Cylinders Hydraulic 3/8 Line (Part # A8013-00) 1 3 2 Item 1 2 3 Component Part # 29174 812841 813303 Description HOSE 3/8 X 168 9/16 SWFJIC X 3/4RB MALE TIP 0.5 BODY 0.75 ORB DUST CAP 0.
bühler 1500 Bale Carrier Fixed Pick Up Cylinder Assembly (Part # A7013-00) TO LIFT PORT ON MAIN VALVE BANK (FRONT PORT) USE 3/8 X 96" HOSE SUPPLIED WITH MAIN FRAME 1 TO LIFT PORT ON VALVE BANK (REAR PORT) USE 3/8 X 96" HOSE SUPPLIED WITH MAIN FRAME 3 2 Item 1 2 3 Component Part # 813640 22510 E2872-00 Description Qty ELBOW 90 9/16 MORB ADJ 9/16 MJIC CYLINDER 3.0 DIA X 16 INLAND ELBOW RESTRICTOR MALE 90° 1 1 1 22510 Cylinder 3.
bühler 1500 Bale Carrier Pusher Motor Assembly (Part # A8011-00) 8 4 6 7 1 5 2 3 Item 1 2 3 4 5 6 7 8 Component Part # C7031-00 C7030-00 C2768-00 967275 84051 84048 813663 B2799-00 Description Qty SPROCKET DRIVE WELDMENT MOTOR 22.2 CU MT WELDT SPROCKET ADJUSTING BOLT FRONT 1NC BOLT HEX 0.500 NC X 2.00 GR8PL NUT HEX JAM 1.00 NC GR2 WASHER 0.500 FLAT SAE BS PL NUT LOCK (STEEL) 0.500 NC GRCPL MOTOR 22.
bühler 1500 Bale Carrier Carrier Hydraulic Assembly Hardware (Part # A8000-04) 5 1 3 1 2 3 4 1 3 5 3 Note: Open-Center Valve is not shown Item 1 2 3 4 5 Component Part # 811795 E2345-00 812363 84072 E1932-00 Description BOLT HEX 0.375 NC X 2.00 GR5PL CYL PIN 1 DIA X 4.5 NUT LOCK (STEEL) 0.375 NC GRBPL BOLT HEX 0.375 NC X 0.
bühler 1500 Bale Carrier Fixed Pick Up Arm Hydraulic Assembly Schematic (Part # A2300-87) A2300-87 *A7013-00 FRONT OF CARRIER *812176 *812176 *A8002-01 NOTES: 1) ALL ITEMS IN THE HYDRAULIC SCHEMATIC THAT ARE MARKED WITH A "*" ARE SUPPLIED ON THE MAIN FRAME ASSEMBLY. 2) LOOP ALL HOSES THROUGH APPROPRIATE HOSE HOLSTERS AND TIE WRAP. 3) DURING FIRST USE CHECK FOR CLEARANCE AND BINDING.
45 DETAIL B R6 R5 R1 NOTES: 1) THE LABELLED LINES IN THE SCHEMATIC CORRESPOND WITH THE PORTS IN DETAIL VIEWS A AND B. BRACKETS REPRESENT THE PART NUMBER. 2) LOOP ALL HOSES THROUGH APPROPRIATE HOSE HOLSTERS AND TIE WRAP. 3) CHECK FOR HOSE CLEARANCE AND BINDING DURING FIRST USE. 4) ALL ITEMS THAT ARE MARKED WITH A "*" ARE SUPPLIED ON THE MAIN FRAME.
bühler 1500 Bale Carrier RPU Squeeze Cylinder (Part # A2400-35) 5 3 TO ROTATE CYLINDER ROD END 9/16 TEE OPEN END THAT POINTS IN THE DIRECTION OF CYLINDER EXTENSION 2 1 4 TO ROTATE CYLINDER BASE END 9/16 TEE OPEN END Item 1 2 3 4 5 Component Part # IN29074 813640 IN29067 24367 813640 Description Qty HOSE 3/8 X 60 9/16 SWFJIC ELBOW 90 9/16 MORB ADJ X 3/8 HOSE 3/8 X 68 9/16 SWFJIC CYLINDER 2.0 X 18.0 INLAND ELBOW 90° 9/16 MORB ADJ X 3/8 1 1 1 1 2 24367 Cylinder 2.
bühler 1500 Bale Carrier RPU Lift Cylinder (Part # A2400-37 Assembled To Existing 22510 Cylinder) CYLINDER PORT (CHECKED FLOW IN) 3 2 SIDE PUMP PORT (FREE FLOW IN) PILOT PORT TO LIFT LOWER PORT ON MAIN VALVE (FRONT PORT) USE EXISTING 3/8 X 96 HOSE SUPPLIED WITH MAIN FRAME 1 TO SEQUENCE VALVE (PORT #2) USE EXISTING 3/8 X 108 HOSE SUPPLIED WITH ROTATE CYLINDER ASSEMBLY TO ROTATE CYLINDER BASE END USE 3/8 X 96 HOSE SUPPLIED WITH ROTATE CYLINDER ASSEMBLY Item 1 2 3 Component Part # 22510 E2872-00 A2
bühler 1500 Bale Carrier Pilot Check Valve Assembly (Part # A2400-37) 1 3 2 4 5 6 7 Item 1 2 3 4 5 6 7 Component Part # IN29098 29043 22203 29020 29023 29039 29015 Description HOSE 3/8 X 14 3/8 FNPT X 9/16 SWFJIC ADAPTOR STR 9/16 MJIC X 3/8 MNPT PILOT CHECK VALVE PC-37 CONNECTOR 9/16 MJIC X 1/4 MNPT TEE 1/4 FNPT RUN X 1/4 MNPT ADAPTOR STR 1/4 MNPT X 9/16 FJIC TEE 9/16 MJIC RUN X 9/16 MORB 48 Qty 1 1 1 1 1 1 1
bühler 1500 Bale Carrier RPU Rotate Cylinder (Part # A2400-36) NOTES: 1) REMOVE TIE ROD SUPPLIED BY MANUFACTURER AND REPLACE WITH MANUFACTURED TIE ROD (ITEM 16). USE NEW ROD TO MOUNT SEQUENCE VALVE HOLDER (ITEM 15).
A8002-00 29105 29105 813667 A7010-00 A7011-00 TO TRACTOR COUPLER (EXTEND) TO TRACTOR COUPLER (RETURN) bühler 1500 Bale Carrier Open-Center Configuration Schematic 50
bühler 1500 Bale Carrier Open-Center Valve (Part # A7016-00) Open-Center Configuration 51
bühler 1500 Bale Carrier Open-Center Valve (Part # A7016-00) Open-Center Configuration Item 1 2 3 4 5 6 Component Part # B7010 812081 812080 811414 813667 29105 Description Qty SERIES/PARALLEL VALVE PLUG 3/4 MORB STL 721-FS0-08 ADAPTOR STR 3/4 MORB X 3/4 MJIC ELBOW 90 3/4 MORB X 3/4 MJIC TEE RUN 3/4 MJIC X 3/4 MORB HOSE 1/2 X 28 - 3/4 SWFJIC 1 3 1 1 1 2 B7010-00 Parallel Valve Service Parts Component Part # 22083-03 22083-01 X2684 Description C07-12TD COIL SERIES PARALLEL VALVE (LOW &HIGH SPEED) SEA
bühler 1500 Bale Carrier 1500 Bale Carrier Hydraulic Schematic 53
bühler 1500 Bale Carrier NOTES PAGE 54
bühler 1500 Bale Carrier APPENDIX C Electrical Assembly WARNING Read and understand the safety messages listed in the 1500 Bale Carrier operator manual. Shut off all power to unit before inspecting, servicing, adjusting or repairing the 1500 Bale Carrier. WARNING For proper operation of the Snubber, power must be supplied to the RED power wire from the control handle. Ensure that there is a 15-amp fuse in place to protect this circuit. Verify prior to installing Snubber.
bühler 1500 Bale Carrier Electrical Schematic NOTE: VALVE HARNESS (1) TERMINATES WITH THE FEMALE SPADE CONNECTORS TO MATCH THE SOLENOID COIL. 2 LOW SPEED 1 - BLACK 1 PUSHER BACK 7 - BROWN 3 PUSHER FWD. 6-BLUE ARM DN. 4-PINK 4 OPEN CENTER 5-ORANGE 5 GROUND 12- GREEN END VIEW CONNECTOR ARM UP 2 - TAN POWER 3-RED 15 AMP FUSE GROUND 12- GREEN POWER 3-RED GROUND 12- GREEN FRONT OF HAYLINER LOW SPEED 1-BLACK PUSHER FWD. 6-BLUE PUSHER BACK 7-BROWN ARM DN.
bühler 1500 Bale Carrier Control Handle Assembly (Part # I20024) Item 1 2 3 4 5 6 7 8 Component Part # INE22105-01 22105 813539 813540 814445 813779 I100016 814448 Description WIRE CLAMP PLATE CONTROL HANDLE 8-32 X 3/8 TRUSS HEAD MACHINE SCREW 8-32 X 1/2 ROUND HEAD MACHINE SCREW ROCKER SWITCH ON/OFF/ON MOMENTARY ROCKER SWITCH ON / OFF SWITCH COVER PLATE - 1500 DECAL BUHLER 1500 57 Qty 1 1 4 2 2 1 1 1
bühler 1500 Bale Carrier NOTES PAGE 58
bühler 1500 Bale Carrier APPENDIX D General Assembly Table of Contents Description Page Carrier Final Assembly…………………..…………………………………………. 60 Carrier Initial Assembly……………………………………………………….……. 62 Tandem Axle Assembly…………………………………………………………. 64 Tandem Axle / 1500………………………………………………………….. 65 Tire Assembly………………………………………………………………. 66 Tandem Axle Assembly…………………………………………………… 67 Hub Assembly……..…………………………………………………….
AMBER LAMP TO THE OUTSIDE A-A 60 15 7 AS VIEWED FROM BACK OF TRAILER RED LAMP TO THE INSIDE 16 AMBER LAMP TO THE OUTSIDE 5 24 DETAIL AA 28 MAIN ELECTRICAL HARNESS 2 18 6 12 8 23 14 9 1 3 11 10 17 22 27 31 33 34 35 36 37 22 26 32 13 4 20 25 30 29 19 bühler 1500 Bale Carrier Carrier Final Assembly (Part # A8000-04)
bühler 1500 Bale Carrier Carrier Final Assembly (Part # A8000-04) Item 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 Component Part # A7006-00 A7008-00 A8011-00 B2363-00 E2345-00 E2413-00 E2937-00 E7038-00 E7040-00 INE7039-00 813949 813643 52955-456 81620 814193 814199 814198 813602 814434 813958 99053 81549 81552 811795 812537 84541 812362 812363 812364 813581 81570 81546 909277 46912 814433 814449 37 814450 Description Qty PUSHER ASSEMBLY CHAIN G
15 23 12 17 26 22 19 18 5 19 18 26 23 17 26 22 4 18 18 3 18 6 18 62 13 19 18 16 21 9 18 13 18 13 19 11 10 18 26 23 8 2 14 1 7 Carrier Initial Assembly (Part # A8000-04) 20 25 25 24 bühler 1500 Bale Carrier
bühler 1500 Bale Carrier Carrier Initial Assembly (Part # A8000-04) Item 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 Component PART # C2369-00 C7055-00 C7057-01 C8003-01 C8004-01 C8010-00 C8014-00 C8015-00 C8016-00 C8017-01 E2445-00 INE7003-01 813646 813647 812288 81581 81620 967274 967275 813515 812363 812364 813663 813648 813590 84048 Description HITCH OUTER CARRIER BEAM CHAIN GUIDE WELDMENT SUBFRAME REAR CROSSMEMBER SAFETY CHAIN WELD'T L.H. HITCH BEAM R.H.
bühler 1500 Bale Carrier Complete Tandem Axle Assembly 3 2 1 4 5 Item 1 2 3 4 5 Component Part # C8005-00 984077 813547 C2407-00 B2400-14 Description AXLE BEAM WELDMENT NUT HEX JAM 0.500NC GR2 PL SETSCREW SQHDCUP 0.
bühler 1500 Bale Carrier Tandem Axle / 1500 (A2400-14) 1 2 Item 1 2 Component Part # B2700-03 B2400-14 Description TIRE ASSEMBLY 1500 / 2500 BALE CARRIER TANDEM AXLE 1500 / HUB ASSEMBLY 65 Qty 2 1
bühler 1500 Bale Carrier Tire Assembly (Part # B2700-03) 3 1 2 Item 1 2 3 Component Part # 813655 813656 813657 Description Qty 15 X 10lb X 6 BOLT P65 RIM TR-416-MS VALVE STEM WITH CAP TIRE 12.
bühler 1500 Bale Carrier Tandem Axle Assembly (Part # B2400-14) 7 7 2 1 3 4 8 5 Item 1 2 3 4 5 6 7 8 Component Part # C2406-00 C2339-00 813649 81206 813673 813650 813646 813651 6 Description TANDEM AXLE 1500 WELDMENT HUB ASSEMBLY DUST SHIELD 3/16" X 1-1/2 " COTTER PIN BLACK NUT CASTLE 1.00 NF DUST CAP GREASE FITTING 1/4 DRIVEN WASHER FLAT 1-1/32" X 2" X .188" BLK.
bühler 1500 Bale Carrier Hub Assembly (Part # C2339-00) 2 1 3 4 5 Item 1 2 3 4 5 Component Part # 813652 967205 967208 967204 813653 Description 6 BOLT WHEEL HUB BEARING CONE OUTER BEARING CONE INNER OIL SEAL SAE-30 9/16" HUB BOLT 68 Qty 1 1 1 1 6
bühler 1500 Bale Carrier Pusher Assembly (Part # A7006-00) 1 4 3 2 7 5 4 3 5 4 6 2 4 Item 1 2 3 4 5 6 7 Component Part # C7027-00 E2749-00 E2750-00 813558 813561 E7032-00 813644 NOTE: USE LOCKTITE ON ALL BRASS SCREWS Description PUSHER TOP SLIDER SIDE SLIDER SCREW MACH M8 X 20 FLHD BRASS NUT HEX M8 BRASS CENTER SLIDER SCREW MACH 0.313NC X 1.
bühler 1500 Bale Carrier Bale Stop Bundle (Part # A8003-00) 3 1 3 2 4 Item 1 2 3 4 Component Part # C8009-00 84048 84277 812364 Description BALE RETAINER WELDT WASHER 0.500 FLAT SAE BS PL BOLT HEX 0.500 NC X 1.50 GR5 PL NUT LOCK (STEEL) 0.
bühler 1500 Bale Carrier Roller / Chain Guide Assembly (Part # A7008-00) 1 2 1 Item 1 2 Component Part # 813645 INE7037-00 Description BEARING / 6205LLU/25.
bühler 1500 Bale Carrier Fixed Pick Up Arm Assembly RH Side (Part # A2300-87) 7 5 7 7 5 8 2 14 1 7 11 6 13 2 10 12 6 13 3 9 ITEM 3 NOT VISIBLE 72 4
bühler 1500 Bale Carrier Fixed Pick Up Arm Assembly RH Side (Part # A2300-87) Item 1 2 3 4 5 6 7 8 9 10 11 12 13 14 Component Part # 811795 812087 812363 812364 813509 81581 81677 84277 C2316-00 C2329-00 C2330-00 E2345-00 E2445-00 INE2485-00 Description BOLT HEX 0.375 NC X 2.00 GR5 PL BOLT HEX 0.625 NC X 6.00 GR8 PL NUT LOCK (STEEL) 0.375 NC GR8 PL NUT LOCK (STEEL) 0.500 NC GR5 PL NUT HEX 0.625 NC GR5 PL BOLT HEX 0.375 NC X 2.50 GR5 PL WASHER LOCK 0.625 PL BOLT HEX 0.500 NC X 1.
bühler 1500 Bale Carrier Bale Deflector Assembly RH (Part # A2400-16) (Optional) 74
bühler 1500 Bale Carrier Bale Deflector Assembly RH (Part # A2400-16) (Optional) Item 1 2 3 4 5 6 7 8 9 10 Component Part # C2451-00 E2453-00 81914 81593 813507 812076 81677 813509 813547 813508 Description BALE DEFLECTOR RH MAIN FRAME SKID COVER RH UHMW POLY BOLT CARR 0.375 NC X 1.00 GR5PL WASHER 0.375 LOCK PL NUT HEX 0.375 NC GR5PL BOLT HEX 0.625 NC X 6.50 GR5PL WASHER LOCK 0.625 PL NUT HEX 0.625 NC GR5PL SET SCREW SQHDCUP 0.500 NC NUT HEX 0.
32 3 5 17 24 6 13 25 76 1 2 8 10 31 8 27 33 30 29 9 2 28 34 30 28 9 37 31 18 22 21 9 11* 15 12 29 16 4 35 23 6 34 14 20 26 12 5 7 5 36 14 3 19 bühler 1500 Bale Carrier RPU Assembly RH Side (Part # A2400-32) (Optional)
bühler 1500 Bale Carrier RPU Assembly RH Side (Part # A2400-32) (Optional) ITEM COMPONENT PART # DESCRIPTION QTY 1 20252 BUSHING 1.75OD x 1.5ID x 1.75 2 2 810215 SCREW SELF TAP 0.313 NC X 0.50 8 3 811795 BOLT HEX 0.375NC X 2.00 GR5 PL 2 4 812087 BOLT HEX 0.625NC X 6.00 GRBPL 2 5 812363 NUT LOCK (STEEL) 0.375 GRB PL 4 6 812364 NUT LOCK (STEEL) 0.500NC GRB PL 2 7 813509 NUT HEX 0.625 NC GR5PL 2 8 813602 RIVET 1/4 X 3/4 FLATHEAD 4 9 813611 PIN SPRING 0.125 DIA X 0.
bühler 1500 Bale Carrier CHECKLIST Predelivery Verify Hardware Torque Verify Rear Wheel Bolt Torque Verify Tire Pressure Inspect Bearing Seals Inspect All Lubrication Points Inspect Chain Drives Inspect Hydraulic Hoses and Electrical Harnesses Dealer Representative: Date: Customer Delivery Review safety procedures regarding 1500 Bale Carrier operation and maintenance. Review Operator’s and Part’s Manual. Review proper operating procedures.
DIVISION LOCATIONS Inland Division 1260 Clarence Avenue Winnipeg, Manitoba R3T 1T2 Ph.: (204) 661-8711 Fax: (204) 654-2503 Allied Division 1260 Clarence Avenue Winnipeg, Manitoba R3T 1T2 Ph.: (204) 661-8711 Fax: (204) 654-2503 Farm King Division 301 Mountain Street S. Morden MB. R6M 1X7 Ph.: (204) 822-4467 Fax: (204) 822-6348 U.S.
