96” Allied Snowblower TABLE OF CONTENTS DESCRIPTION PAGE Warranty ...................................................................... 1 Safety Instructions & Safety Sign Locations ................ 2 Operating Instructions.................................................. 3 Assembly Instructions .................................................. 5 96” Allied Snowblower Drawings.................................. 8 96” Allied Snowblower Parts List .................................
96” Allied Snowblower WARRANTY REGISTRATION AND POLICY Buhler Manufacturing products are warranted for a period of twelve (12) months from original date of purchase, by original purchaser, to be free from defects in material and workmanship under correct, normal agricultural use and proper applications.
96” Allied Snowblower SNOWBLOWER This manual is for 96" Allied Snowblower with a quick coupling hitch. With this hitch, the blower can be mounted on a tractor with either a quick hitch or the standard three-point hitch. All 96" Allied snowblowers have a sealed oil bath gearbox. The snowblower is the push type and will mount to a tractor with 540 rpm PTO. It is supplied with category 2 pins with conversion bushings to category 3 available.
96” Allied Snowblower OPERATING INSTRUCTIONS 1. Do not operate the blower in the fully raised position. The three-point hitch on some tractors rises high enough to cause the PTO shaft to bind. This can cause damage to the PTO shaft and/or to the hitch and pins. 2. Depth of cut can be partially controlled by tilting the blower forward or backward. Adjust the tractor quick hitch so the snowblower is just slightly tilted back when resting on the ground.
96” Allied Snowblower OPERATING INSTRUCTIONS – cont’d 11. Shear Sprocket: The shear sprocket (#24) should be checked at the beginning of every season to make sure it will spin freely. With time this sprocket could corrode and seize which will not allow the shear bolt to break if something jams in the snowblower auger. Clean to loosen if necessary. 12.
96” Allied Snowblower ASSEMBLY INSTRUCTIONS 1. Fasten the two quick hitch arms (#57 & #58, left and right) to the main body. Use eight 5/8” x 1 ¼” hex bolts, lock washers and hex nuts. Note: Lift arms for quick coupling hitch are 30 ¾” long versus 35” for the standard three point hitch. 2. Bolt the quick hitch (#56) to the snowblower body using two ½” x 1 ¼” hex bolts, lock washers and hex nuts. Fasten to the lift arms using three 5/8" x 1 ½” hex bolts on each lift arm.
96” Allied Snowblower ASSEMBLY INSTRUCTIONS – cont’d. 7. Mounting blower on tractor: a) b) c) d) e) The pins supplied with the snowblower are for a category 2 quick hitch. The quick coupling hitch has two holes both at the top of the hitch and at each lift arm. When using a quick coupler, the pins must be in the inside set of holes. Use the outside set of holes with a standard three-point hitch.
96” Allied Snowblower ASSEMBLY INSTRUCTIONS – cont’d. 8. PTO SHIELD All snowblowers are supplied with a PTO shield (#61). To install, remove the two rear bolts at the top of the gearbox (#38). Bolt the PTO shield to the gearbox by the hinges using these same bolts. A utility spring (#62) keeps the shield in place. Hook one end of the spring in the hole in the shield and the other end to the hole in the brace under the gearbox. CAUTION: Do not run the snowblower without this shield in place.
6” Allied Snowblower 96” SNOWBLOWER W/QUICK HITCH -8-
96” Allied Snowblower -9-
96” Allied Snowblower WHEN ORDERING PARTS Always give your dealer the Model and Serial Number of your machine to assist him in ordering and obtaining the correct parts. Use the exploded view and tabular listing of the area of interest to exactly identify the required part.
96” Allied Snowblower 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 965919A 965964 965923 967140 BU50505 F0585 965925A 968807 81627 902377 81552 811702 961676 967164 81549 81620 965803 965970A 9812433 965927 84289 965928A FX9204 965952A 965953A 812026 965966 965967 960135 965968 812364 988999 81593 81592 965646 903523 961012 902407 900712 86171 FX9102 936402 Drive Shaft Guard 1/4'' Cable x 70'' Long Swivel Arm 1'' x 10ga Narr
96” Allied Snowblower 96” ALLIED SNOWBLOWER PTO (Standard and Optional Long) - 12 -
96” Allied Snowblower 96" ALLIED SNOWBLOWER PTO (Optional Long) Item # Part # 1 2 F0586 907996 907997 907989 936199 3 936249 *4 903296 903297 812362 936197 906548 907998 907991 907999 908000 908001 907995 81627 812364 908002 936411 5 6 7 8 9 10 11 12 13 14 15 16 Description Shaft Complete Tractor Half of PTO (Shear) Implement Half of PTO (Clamp Yoke) Shear Assembly Safety Slide Lock Repair Kit (Collar, Spring, Ret.
96” Allied Snowblower 96" ALLIED SNOWBLOWER PTO (Standard) Item # Part # Description 1 2 F0585 907987 907988 907989 936199 3 936249 4 903296 903297 812362 936197 906548 907994 907991 907993 907992 907990 907995 81627 812364 908002 936411 Shaft Complete Tractor Half of PTO (Shear) Implement Half of PTO (Clamp Yoke) Shear Assembly Safety Slide Lock Repair Kit (Collar, Spring, Ret.
96” Allied Snowblower 96” ALLIED SNOWBLOWER GEARBOX 960 FK, 74", 85", & 96" ALLIED SNOWBLOWER GEARBOX PARTS LIST Item # 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 Part # Description BU50505 BU50310 BU500089-3 BU50457 BU500167-1 BU50458 BU50507 BU50502 BU50329 BU50331 BU50428 BU50444 BU50422-1 BU50415 BU575902 BU575901 BU50429 BU50210X BU575907 BU575906 BU500397-6 BU50417-1 Gearbox Complete Gearbox Casting Only Pipe Plug Gearbox Cover Relief Valve Gearbox Gasket Cross Shaft Pinion Shaft Beve
96” Allied Snowblower 3.5 X 8 CYLINDER ASSEMBLY Item # Part # Description 1 2 3 24803 24804 113934 X2098 Cyl Complete Tube Weldt Piston Rod 1.5 Dia Seal Kit 1.75 X 5 CYLINDER ASSEMBLY Item # Part # Description 1 2 3 24930 115367 112104 X2669 Cyl Complete Tube Weldt Shaft Weldt 1.
96” Allied Snowblower 96” ALLIED SNOWBLOWER BUNDLES QUANTITY BUNDLE NO.
