2010 Buick Enclave Owner Manual M In Brief . . . . . . . . . . . . . . . . . . . . . . . . 1-1 Instrument Panel . . . . . . . . . . . . . . 1-2 Initial Drive Information . . . . . . . . 1-3 Vehicle Features . . . . . . . . . . . . . 1-14 Performance and Maintenance . . . . . . . . . . . . . . . . 1-18 Keys, Doors and Windows . . . 2-1 Keys and Locks . . . . . . . . . . . . . . . 2-2 Doors . . . . . . . . . . . . . . . . . . . . . . . . . . 2-9 Vehicle Security. . . . . . . . . . . . . .
010 Buick Enclave Owner Manual M Wheels and Tires . . . . . . . . . . . 10-37 Jump Starting . . . . . . . . . . . . . . . 10-80 Towing . . . . . . . . . . . . . . . . . . . . . . 10-84 Appearance Care . . . . . . . . . . . 10-87 Service and Maintenance . . . 11-1 General Information . . . . . . . . . . 11-1 Scheduled Maintenance . . . . . . 11-2 Recommended Fluids, Lubricants, and Parts . . . . . . . 11-7 Maintenance Records . . . . . . . 11-10 Technical Data . . . . . . . . . . . . . . .
Introduction GENERAL MOTORS, GM, the GM Emblem, BUICK, the BUICK Emblem are registered trademarks; and the name ENCLAVE is a trademark of General Motors. This manual describes features that may or may not be on your specific vehicle either because they are options that you did not purchase or due to changes subsequent to the printing of this owner manual. Please refer to the purchase documentation relating to your specific vehicle to confirm each of the features found on your vehicle.
iv Introduction Using this Manual To quickly locate information about the vehicle use the Index in the back of the manual. It is an alphabetical list of what is in the manual and the page number where it can be found. Danger, Warnings, and Cautions { WARNING These mean there is something that could hurt you or other people. Notice: This means there is something that could result in property or vehicle damage. This would not be covered by the vehicle's warranty.
Introduction Vehicle Symbol Chart Here are some additional symbols that may be found on the vehicle and what they mean. For more information on the symbol, refer to the index. 9 : Airbag Readiness Light # : Air Conditioning ! : Antilock Brake System (ABS) g : Audio®Steering Wheel Controls or OnStar $ : Brake System Warning Light " : Charging System I : Cruise Control B : Engine Coolant Temperature O : Exterior Lamps # : Fog Lamps .
vi Introduction 2 NOTES
In Brief In Brief Instrument Panel Instrument Panel . . . . . . . . . . . . . . 1-2 Initial Drive Information Initial Drive Information . . . . . . . . 1-3 Remote Keyless Entry (RKE) System . . . . . . . . . . . . . . . . . . . . . . 1-4 Remote Vehicle Start . . . . . . . . . 1-4 Door Locks . . . . . . . . . . . . . . . . . . . 1-5 Liftgate . . . . . . . . . . . . . . . . . . . . . . . . 1-5 Windows . . . . . . . . . . . . . . . . . . . . . . 1-6 Seat Adjustment . . . . . . . . . . . . . .
1-2 In Brief Instrument Panel
In Brief A. Air Vents on page 8‑9. L. Horn on page 5‑5. B. Windshield Wiper/Washer on page 5‑5. M. Steering Wheel Controls on page 5‑3. C. Instrument Cluster on page 5‑13. N. Hazard Warning Flashers on page 6‑4. D. Driver Information Center (DIC) Buttons. See Driver Information Center (DIC) on page 5‑25. O. Dual Automatic Climate Control System on page 8‑1. E. Clock on page 5‑9. P. Center Console Shift Lever. See “Console Shift Lever” under Shifting Into Park on page 9‑21. F.
1-4 In Brief Remote Keyless Entry (RKE) System The RKE transmitter is used to remotely lock and unlock the doors from up to 60 m (195 feet) away from the vehicle. Press Q to lock all doors. Lock and unlock feedback can be personalized. To open or close the liftgate, press and hold & until the liftgate begins to move. Press L and release to locate the vehicle. Press L and hold for more than two seconds to sound the panic alarm. Press L again to cancel the panic alarm.
In Brief 1-5 Canceling a Remote Start Power Door Locks Power Liftgate To cancel a remote start: On vehicles with power door locks, the controls are located on the front doors. On vehicles with a power liftgate, the vehicle must be in P (Park) to operate it. " (Unlock): Press to unlock the doors. . Press and hold the liftgate button & on the Remote Keyless Entry (RKE) transmitter. . Press the liftgate button on the center console. . Press the touchpad switch on the outside liftgate handle. .
1-6 In Brief Windows Seat Adjustment Power Seats Raise or lower the seat by moving the control (A) up or down. See Power Seat Adjustment on page 3‑3. To raise or recline the seatback, tilt the top of the control (B) forward or rearward. See Reclining Seatbacks on page 3‑5. Press the front or rear of the control (C) to increase or decrease lumbar support. On vehicles with power windows, the switches are on the driver door armrest. Each passenger door has a switch that controls only that window.
In Brief Second Row Seats Third Row Seats Heated Seats The third row seats can be folded forward or removed. Heated Front Seats 1-7 The heated seat controls are located on the center console. The engine must be running to operate them. I : Press to turn on the heated seatback. J : Press to turn on or off the heated seat and seatback. For more information see Heated Front Seats on page 3‑7.
1-8 In Brief Heated and Ventilated Seats Safety Belt Sensing System for Passenger Airbag On vehicles with this feature, the controls are on the front doors near the handle. H: z: Press to ventilate the seat. Press to heat the seat. For more information see Heated and Ventilated Front Seats on page 3‑8. Head Restraint Adjustment Do not drive until the head restraints for all occupants are installed and adjusted properly. For more information see Head Restraints on page 3‑2.
In Brief conditions. The driver airbag, seat‐mounted side impact airbags, and roof‐rail airbags are not affected by the passenger sensing system. 1-9 Mirror Adjustment To adjust each mirror: Exterior Mirrors 1. Press (A) or (B) to select the driver or passenger side mirror. 2. Press one of the four arrows located on the control pad to adjust the mirror. The passenger airbag status indicator will be visible on the instrument panel when the vehicle is started.
1-10 In Brief Interior Mirror The vehicle has an automatic dimming rearview mirror. Automatic dimming reduces the glare from the headlamps of the vehicle behind you. The dimming feature comes on and the indicator light illuminates each time the ignition is turned to start. Steering Wheel Adjustment Power Tilt Wheel See Automatic Dimming Rearview Mirror on page 2‑18. The adjustment lever is located on the left side of the steering column.
In Brief Interior Lighting Dome Lamp Override Dome Lamps The dome lamp override button is next to the exterior lamps control. The dome lamps are located in the overhead console and above the rear seat passengers. The dome lamps automatically come on when a door is opened, unless the dome lamp override button is pressed in. To manually turn them on, turn the instrument panel brightness control clockwise to the farthest position.
1-12 In Brief ;: Manual operation of the parking lamps and other exterior lamps, except the headlamps. 2: Manual operation of the headlamps and other exterior lamps. Windshield Wiper/Washer 6: The windshield wiper/washer lever is located on the left side of the steering column. 1 : Slow wipes. 2 : Fast wipes. Windshield Washer # (If Equipped): Push the fog lamp button in to turn on the fog lamps.
In Brief Climate Controls See Dual Automatic Climate Control System on page 8‑1. For more information about the rear climate control, see Rear Climate Control System (Rear Climate Control Only) on page 8‑7 or Rear Climate Control System (Rear Climate with Rear Seat Audio) on page 8‑8. A. Fan Control H. Display B. AUTO I. C. Defrost J. Rear Window Defogger D. Air Recirculation K. Air Conditioning E. REAR (Rear Climate Control) L. PASS (Passenger) F. Air Delivery Mode Control M.
1-14 In Brief 4: Vehicle Features Change the display between the radio station frequency and the time, if equipped. While the ignition is off, press 4 to display the time. Radio(s) For more information about these and other radio features, see Operation on page 7‑2. Storing a Favorite Station A maximum of 36 stations can be stored as favorites using the six softkeys located below the radio station frequency tabs and by using the radio FAV button.
In Brief 1-15 Setting the Clock Satellite Radio Portable Audio Devices To set the time and date for the radio with CD, DVD, and USB Port: Vehicles with an XM™ Satellite Radio tuner and a valid XM Satellite Radio subscription can receive XM programming. This vehicle may have an auxiliary input located on the radio faceplate and a USB port located in the center console. External devices such as iPod®, laptop computers, MP3 players, CD changers, USB storage device, etc.
1-16 In Brief The Bluetooth-enabled cell phone must be paired with the in-vehicle Bluetooth system before it can be used in the vehicle. Not all phones will support all functions. b g : Press to silence the vehicle speakers only. Press again to turn the sound on. Press and hold longer than two seconds to interact with OnStar® or Bluetooth systems. See Bluetooth on page 7‑46. + e − e : Increases or decreases volume. Steering Wheel Controls c : Press to reject an incoming call, or to end a call.
In Brief Cruise Control T: On/Off. + RES : Press to accelerate or resume speed. SET– : Press to set speed or decrease speed. [: Press to cancel cruise control. See Cruise Control on page 9‑32. 1-17 Storage Compartments For vehicles with a second row center console, open each area to access the storage compartment inside. Press the buttons (B, C) on the front of the consoles to access the upper and lower storage areas. Increase the storage area by folding the top of the console forward.
1-18 In Brief Power Outlets Performance and Maintenance The vehicle has three 12‐volt accessory power outlets which can be used to plug in electrical equipment, such as a cellular telephone. StabiliTrak® The power outlets are located: . On the instrument panel below the climate controls. . At the rear of the center floor console. . In the rear cargo area. To use the outlets, remove the cover. See Power Outlets on page 5‑10.
In Brief Tire Pressure Monitor This vehicle may have a Tire Pressure Monitor System (TPMS). The Tire Pressure Monitor System alerts you when a significant reduction in pressure occurs in one or more of your vehicle’s tires by illuminating the low tire pressure warning light on the instrument cluster. If the warning light comes on, stop as soon as possible and inflate the tires to the recommended pressure shown on the tire loading information label located on the driver side center pillar (B pillar).
1-20 In Brief Resetting the Oil Life System 1. Turn the ignition to ON/RUN, with the engine off. 2. Press the vehicle information button until “Oil Life Remaining” displays. 3. Press and hold the set/reset button until “100%” is displayed. Three chimes sound and the “Change Engine Oil Soon” message goes off. . Avoid idling the engine for long periods of time. . When road and weather conditions are appropriate, use cruise control, if equipped. . . Keep vehicle tires properly inflated. .
In Brief Online Owner Center Automatic Crash Response The Online Owner Center is a complimentary service that includes online service reminders, vehicle maintenance tips, online owner manual, special privileges and more. In a crash, built in sensors can automatically alert an OnStar advisor who is immediately connected to the vehicle to see if you need help. Sign up today at: www.gmownercenter.com/buick (U.S.) or www.gm.ca (Canada).
1-22 In Brief OnStar service cannot work unless the vehicle is in a place where OnStar has an agreement with a wireless service provider for service in that area. OnStar service also cannot work unless the vehicle is in a place where the wireless service provider OnStar has hired for that area has coverage, network capacity and reception when the service is needed, and technology that is compatible with the OnStar service.
Keys, Doors and Windows Keys, Doors and Windows Doors Keys . . . . . . . . . . . . . . . . . . . . . . . . . . Remote Keyless Entry (RKE) System . . . . . . . . Remote Keyless Entry (RKE) System Operation . . . . . . . . . . . . . . . . . . . . Remote Vehicle Start . . . . . . . . . Door Locks . . . . . . . . . . . . . . . . . . . Power Door Locks . . . . . . . . . . . . Delayed Locking . . . . . . . . . . . . . . Automatic Door Locks . . . . . . . . . Lockout Protection . . . . . . . . . . . .
2-2 Keys, Doors and Windows If you are locked out of the vehicle, call the Roadside Assistance Center. See Roadside Assistance Program on page 13‑6. Keys and Locks Keys { WARNING Leaving children in a vehicle with the ignition key is dangerous for many reasons, children or others could be badly injured or even killed. They could operate the power windows or other controls or even make the vehicle move.
Keys, Doors and Windows . Check the transmitter's battery. See “Battery Replacement” later in this section. . If the transmitter is still not working correctly, see your dealer/retailer or a qualified technician for service. when Q is pressed again within five seconds. See Vehicle Personalization on page 5‑40 for additional information. Pressing Q may arm the content theft‐deterrent system. See Anti-Theft Alarm System on page 2‑12.
2-4 Keys, Doors and Windows & (Power Liftgate): Press and hold until the liftgate begins to move to open or close the liftgate. The taillamps flash and a chime sounds to indicate when the liftgate is opening or closing. L (Vehicle Locator/Panic Alarm): Press and release to locate the vehicle. The parking lamps flash and the horn sounds three times. Press and hold L for more than two seconds to activate the panic alarm. The parking lamps flash and the horn sounds repeatedly for 30 seconds.
Keys, Doors and Windows Remote Vehicle Start This vehicle may have a remote starting feature that starts the engine from outside of the vehicle. There are other conditions which can affect the performance of the transmitter, see Remote Keyless Entry (RKE) System on page 2‑2 for additional information. / (Remote Start): This button is located on the RKE transmitter if the vehicle has remote start. Starting the Engine Using Remote Start Laws in some communities may restrict the use of remote starters.
2-6 Keys, Doors and Windows Extending Engine Run Time To extend the engine run time by 10 minutes, repeat Steps 1 though 3 while the engine is still running. The engine run time can only be extended if it is the first remote start since the vehicle has been driven. Remote start can be extended one time. If the remote start procedure is used again before the first 10 minute time frame has ended, the first 10 minutes will immediately expire and the second 10 minute time frame will start.
Keys, Doors and Windows Door Locks { WARNING WARNING (Continued) . Unlocked doors can be dangerous. . Passengers, especially children, can easily open the doors and fall out of a moving vehicle. When a door is locked, the handle will not open it. The chance of being thrown out of the vehicle in a crash is increased if the doors are not locked. So, all passengers should wear safety belts properly and the doors should be locked whenever the vehicle is driven. (Continued) .
2-8 Keys, Doors and Windows Pressing the power lock switch twice or the lock button on the RKE transmitter twice will override the delayed locking feature and immediately lock all the doors. This feature will not operate if the key is in the ignition. This feature can be programmed by using the Driver Information Center (DIC). See “DELAY DOOR LOCK” under Vehicle Personalization on page 5‑40.
Keys, Doors and Windows Doors WARNING (Continued) Liftgate Manual Liftgate Operation { WARNING Exhaust gases can enter the vehicle if it is driven with the liftgate, trunk/hatch open, or with any objects that pass through the seal between the body and the trunk/hatch or liftgate. Engine exhaust contains Carbon Monoxide (CO) which cannot be seen or smelled. It can cause unconsciousness and even death. (Continued) If the vehicle must be driven with the liftgate, or trunk/hatch open: .
2-10 Keys, Doors and Windows Power Liftgate Operation The vehicle may have a power liftgate. The vehicle must be in P (Park) to use this feature. The power liftgate can be power opened and closed in the following ways: . The taillamps will flash and a chime will sound when the power liftgate is used. Pressing the buttons or touchpad a second time while the liftgate is moving reverses the direction. Press and hold the power liftgate button on the RKE transmitter.
Keys, Doors and Windows If the transmission is shifted out of P (Park) while the power function is in progress, the liftgate power function will continue to completion. If the transmission is shifted out of P (Park) and the vehicle accelerates before the power liftgate latches closed, the liftgate may reverse to the open position. Cargo could fall out of the vehicle. Always make sure the power liftgate is closed and latched before you drive away.
2-12 Keys, Doors and Windows To open the liftgate, press the touchpad on the handle on the outside of the liftgate and lift the gate open. To close the liftgate, use the pull cup to lower the liftgate and close. The liftgate latch will power close. Always close the liftgate before driving. If the RKE button or the power close button on the liftgate is pressed while power operation is disabled, the lights will flash three times, but the liftgate will not move.
Keys, Doors and Windows If a locked door is opened without using the RKE transmitter, a ten second pre-alarm occurs. The horn chirps and the lights flash. If the key is not placed in the ignition and turned to START or the door is not unlocked by pressing Q during the ten second pre-alarm, the alarm goes off. The headlamps flash and the horn sounds for about 30 seconds, then turns off to save the battery power. The vehicle can be started with the correct ignition key if the alarm has been set off.
2-14 Keys, Doors and Windows You do not have to manually arm or disarm the system. The security light comes on if there is a problem with arming or disarming the theft-deterrent system. When the PASS-Key® III+ system senses an incorrect key, the vehicle does not start. Anyone using a trial-and-error method to start the vehicle will be discouraged because of the high number of electrical key codes.
Keys, Doors and Windows 3. After the engine has started, turn the key to LOCK/OFF, and remove the key. 4. Insert the key to be programmed and turn it to the ON/RUN position within five seconds of the original key being turned to the LOCK/OFF position. The security light turns off once the key has been programmed. 5. Repeat Steps 1 through 4 if additional keys are to be programmed. If the PASS-Key® III+ key is lost or damaged, see your dealer/retailer or a locksmith to have a new key made.
2-16 Keys, Doors and Windows Power Mirrors To adjust each mirror: 1. Press (A) or (B) to select the driver or passenger side mirror. For vehicles with outside power foldaway mirrors: 2. Press one of the four arrows located on the control pad to adjust the mirror. 3. Adjust each outside mirror so that a little of the vehicle and the area behind it can be seen. 4. Press either (A) or (B) again to deselect the mirror. Controls for the outside power mirrors are located on the driver door armrest.
Keys, Doors and Windows Resetting the Power Foldaway Mirrors Reset the power foldaway mirrors if: . The mirrors are accidentally obstructed while folding. . They are accidentally manually folded/unfolded. . The mirrors vibrate at normal driving speeds. Fold and unfold the mirrors one time using the mirror controls to reset them to their normal position. A popping noise may be heard during the resetting of the power foldaway mirrors. This sound is normal after a manual folding operation.
2-18 Keys, Doors and Windows Interior Mirrors O (On/Off): Press to turn the dimming feature on or off. Automatic Dimming Rearview Mirror The vehicle may also have a Rear Vision Camera (RVC). See Rear Vision Camera (RVC) on page 9‑36 for more information. The vehicle has an automatic dimming inside rearview mirror. Automatic dimming reduces the glare from the headlamps of the vehicle behind you. The dimming feature comes on and the indicator light illuminates each time the ignition is turned to start.
Keys, Doors and Windows 2-19 WARNING (Continued) They could operate the power windows or other controls or even make the vehicle move. The windows will function and they could be seriously injured or killed if caught in the path of a closing window. Do not leave keys in a vehicle with children. Power Windows { WARNING Leaving children in a vehicle with the keys is dangerous for many reasons, children or others could be badly injured or even killed.
2-20 Keys, Doors and Windows Express-Up/Express-Down Windows Programming the Power Windows A window with the express‐up/down feature allows it to be raised or lowered without holding the switch. Press or pull the window switch fully and release it to activate the express feature. The express mode can be canceled by pressing or pulling the switch.
Keys, Doors and Windows Sun Visors Pull the sun visor down to block glare. Detach the sun visor from the center mount and slide it along the rod from side-to-side to cover the driver or passenger side of the front window. Swing the sun visor to the side to cover the side window. It can be moved along the rod from side-to-side in this position also. Lighted Visor Vanity Mirror The vehicle has lighted visor vanity mirrors on both the driver and passenger sun visors.
2-22 Keys, Doors and Windows Express-open/Express-close: From the closed position, press and release the rear of the switch to express-open the sunroof. Press and release the front of the switch to express-close the sunroof. Rear Power Sunshade On vehicles with a rear power sunshade, the switch is on the headliner above the rearview mirror. To open the rear sunshade, located over the second row seats, press and release the rear of the switch.
Seats and Restraints Seats and Restraints Safety Belt Extender . . . . . . . . . Safety System Check . . . . . . . . Safety Belt Care . . . . . . . . . . . . . Replacing Safety Belt System Parts After a Crash . . . . . . . . . Head Restraints Head Restraints . . . . . . . . . . . . . . . 3-2 Front Seats Power Seat Adjustment . . . . . . . 3-3 Lumbar Adjustment . . . . . . . . . . . 3-4 Reclining Seatbacks . . . . . . . . . . 3-5 Heated Front Seats . . . . . . . . . . .
3-2 Seats and Restraints Head Restraints The vehicle's front seats have adjustable head restraints in the outboard seating positions. { WARNING With head restraints that are not installed and adjusted properly, there is a greater chance that occupants will suffer a neck/ spinal injury in a crash. Do not drive until the head restraints for all occupants are installed and adjusted properly. Adjust the head restraint so that the top of the restraint is at the same height as the top of the occupant's head.
Seats and Restraints Front Seats Power Seat Adjustment If the vehicle has power seats, the controls are located on the outboard side of the seats. Move the seat forward or rearward by sliding the power seat adjustment control (A) forward or rearward. The vehicle may have additional features to adjust the power seat: . Driver Seat with Power Seat Control, Power Recline, and Power Lumbar shown A. Power Seat Adjustment Control B. Reclining Seatbacks on page 3‑5. C. Lumbar Adjustment on page 3‑4.
3-4 Seats and Restraints A second seating and mirror position can be programmed by repeating the above steps and pressing button 2. To recall the memory positions, the vehicle must be in P (Park). Press and release either button 1 or 2. The seat, outside mirrors, and power steering column will move to the position previously stored. You will hear a single beep.
Seats and Restraints Power Lumbar Reclining Seatbacks On vehicles with power lumbar, the controls used to operate this feature are located on the outboard side of the seats. See “Power Lumbar” under Power Seat Adjustment on page 3‑3 for more information. Manual Reclining Seatbacks To increase or decrease lumbar support, press and hold the front or rear of the control (C). Release the control when the seatback reaches the desired level of lumbar support.
3-6 Seats and Restraints To return the seatback to an upright position: 1. Lift the lever without applying pressure to the seatback and the seatback will return to the upright position. 2. Push and pull on the seatback to make sure it is locked. Power Reclining Seatbacks On vehicles with seats that have power reclining seatbacks, the control used to recline them is located on the outboard side of the seat behind the power seat control.
Seats and Restraints Heated Front Seats { WARNING If you cannot feel temperature change or pain to the skin, the seat heater may cause burns even at low temperatures. To reduce the risk of burns, people with such a condition should use care when using the seat heater, especially for long periods of time. Do not place anything on the seat that insulates against heat, such as a blanket, cushion, cover or similar item. This may cause the seat heater to overheat.
3-8 Seats and Restraints Heated and Ventilated Front Seats { WARNING If you cannot feel temperature change or pain to the skin, the seat heater may cause burns even at low temperatures. To reduce the risk of burns, people with such a condition should use care when using the seat heater, especially for long periods of time. Do not place anything on the seat that insulates against heat, such as a blanket, cushion, cover or similar item. This may cause the seat heater to overheat.
Seats and Restraints Entering and Exiting the Third Row 3. Place folding armrests in the upright position. 4. Ensure that the safety belt is unfastened and in the stowed position. { WARNING Using the third row seating position while the second row is folded, or folded and tumbled, could cause injury in a sudden stop or crash. Be sure to return the seat to the passenger seating position. Push and pull on the seat to make sure it is locked into place.
3-10 Seats and Restraints 4. Push down on the rear of the seat cushion until it is locked in place. 5. Push and pull on the seatback and seat cushion to make sure they are locked in place. 6. Check that the safety belt is not under the seat cushion. Reclining the Seatbacks To recline the seatback: 1. Leaning forward in the seat, pull the reclining seatback strap (B). 2. Move the seatback to the desired position, then release the strap to lock the seatback in place. 3.
Seats and Restraints Third Row Seats { WARNING To fold the seatback: 1. Remove anything on or under the seat. Using the third row seating position while the second row is folded, or pushed forward in the entry position, could cause injury in a sudden stop or crash. Be sure to return the seat to the passenger seating position. Push and pull on the seat to make sure it is locked into place. The third row seats can be folded forward or removed.
3-12 Seats and Restraints To return the seatback to the seating position: 1. Raise the seatback into place by using the pullstrap from the rear of the vehicle, or by pushing it into place from inside the vehicle. 2. The headrest must be locked into place before sitting in the seat. { WARNING If either seatback is not locked, it could move forward in a sudden stop or crash. That could cause injury to the person sitting there. Always push and pull on the seatbacks to be sure they are locked. 3.
Seats and Restraints The seats must be placed in the proper locations to attach correctly. The wider seat must be installed on the driver side and the narrower seat on the passenger side. Remove the bolts from the holes in the floor before installing the seats. 2. Place the seat on the vehicle floor so that the front seat hooks are on the vehicle bars. 3. Reinstall the bolts, and torque to 55 Y (41 lb ft). Pull up on the seat to make sure it is locked in place. 4. Raise the seatback to its upright position.
3-14 Seats and Restraints In most states and in all Canadian provinces, the law requires wearing safety belts. Here is why: You never know if you will be in a crash. If you do have a crash, you do not know if it will be a serious one. Why Safety Belts Work When you ride in or on anything, you go as fast as it goes. A few crashes are mild, and some crashes can be so serious that even buckled up, a person would not survive. But most crashes are in between.
Seats and Restraints Get it up to speed. Then stop the vehicle. The rider does not stop. The person keeps going until stopped by something. In a real vehicle, it could be the windshield... or the instrument panel...
3-16 Seats and Restraints Questions and Answers About Safety Belts Q: Will I be trapped in the vehicle after a crash if I am wearing a safety belt? or the safety belts! With safety belts, you slow down as the vehicle does. You get more time to stop. You stop over more distance, and your strongest bones take the forces. That is why safety belts make such good sense. A: You could be — whether you are wearing a safety belt or not.
Seats and Restraints How to Wear Safety Belts Properly This section is only for people of adult size. First, before you or your passenger(s) wear a safety belt, there is important information you should know. Be aware that there are special things to know about safety belts and children. And there are different rules for smaller children and infants. If a child will be riding in the vehicle, see Older Children on page 3‑44 or Infants and Young Children on page 3‑47.
3-18 Seats and Restraints Q: What is wrong with this? { WARNING Q: What is wrong with this? You can be seriously hurt if your shoulder belt is too loose. In a crash, you would move forward too much, which could increase injury. The shoulder belt should fit snugly against your body. A: The shoulder belt is too loose. It will not give as much protection this way. A: The lap belt is too loose. It will not give nearly as much protection this way.
Seats and Restraints { WARNING Q: What is wrong with this? You can be seriously hurt if your lap belt is too loose. In a crash, you could slide under the lap belt and apply force on your abdomen. This could cause serious or even fatal injuries. The lap belt should be worn low and snug on the hips, just touching the thighs. 3-19 { WARNING You can be seriously injured if your belt is buckled in the wrong place like this. In a crash, the belt would go up over your abdomen.
3-20 Seats and Restraints Q: What is wrong with this? { WARNING Q: What is wrong with this? You can be seriously injured if your belt goes over an armrest like this. The belt would be much too high. In a crash, you can slide under the belt. The belt force would then be applied on the abdomen, not on the pelvic bones, and that could cause serious or fatal injuries. Be sure the belt goes under the armrests. A: The belt is over an armrest. A: The shoulder belt is worn under the arm.
Seats and Restraints { WARNING You can be seriously injured if you wear the shoulder belt under your arm. In a crash, your body would move too far forward, which would increase the chance of head and neck injury. Also, the belt would apply too much force to the ribs, which are not as strong as shoulder bones. You could also severely injure internal organs like your liver or spleen. The shoulder belt should go over the shoulder and across the chest.
3-22 Seats and Restraints Q: What is wrong with this? { WARNING You can be seriously injured by a twisted belt. In a crash, you would not have the full width of the belt to spread impact forces. If a belt is twisted, make it straight so it can work properly, or ask your dealer/retailer to fix it. A: The belt is twisted across the body. Lap-Shoulder Belt All seating positions in the vehicle have a lap-shoulder belt.
Seats and Restraints 3-23 5. If equipped with a shoulder belt height adjuster, move it to the height that is right for you. See “Shoulder Belt Height Adjustment” later in this section for instructions on use and important safety information. 2. Pick up the latch plate and pull the belt across you. Do not let it get twisted. The lap-shoulder belt may lock if you pull the belt across you very quickly. If this happens, let the belt go back slightly to unlock it. Then pull the belt across you more slowly.
3-24 Seats and Restraints Before a door is closed, be sure the safety belt is out of the way. If a door is slammed against a safety belt, damage can occur to both the safety belt and the vehicle. Shoulder Belt Height Adjuster The vehicle has a shoulder belt height adjuster for the driver and right front passenger seating positions. To unlatch the belt, push the button on the buckle. The belt should return to its stowed position.
Seats and Restraints Safety Belt Pretensioners This vehicle has safety belt pretensioners for the front outboard occupants. Although the safety belt pretensioners cannot be seen, they are part of the safety belt assembly. They can help tighten the safety belts during the early stages of a moderate to severe frontal, near frontal, or rear crash if the threshold conditions for pretensioner activation are met.
3-26 Seats and Restraints To access the comfort guide, you will first need to move the headrest forward by pulling on the handle behind the seatback. The comfort guide will now be accessible. 2. Place the guide over the belt and insert the two edges of the belt into the slots of the guide. Third Row Center Position Pull the comfort guide out of its storage location and then return the headrest to its upright position. 3. Be sure that the belt is not twisted and it lies flat.
Seats and Restraints 3-27 Safety Belt Use During Pregnancy { WARNING A safety belt that is not properly worn may not provide the protection needed in a crash. The person wearing the belt could be seriously injured. The shoulder belt should go over the shoulder and across the chest. These parts of the body are best able to take belt restraining forces. Safety belts work for everyone, including pregnant women.
3-28 Seats and Restraints The best way to protect the fetus is to protect the mother. When a safety belt is worn properly, it is more likely that the fetus will not be hurt in a crash. For pregnant women, as for anyone, the key to making safety belts effective is wearing them properly. Safety Belt Extender If the vehicle's safety belt will fasten around you, you should use it. But if a safety belt is not long enough, your dealer/retailer will order you an extender.
Seats and Restraints Replacing Safety Belt System Parts After a Crash { WARNING A crash can damage the safety belt system in the vehicle. A damaged safety belt system may not properly protect the person using it, resulting in serious injury or even death in a crash. To help make sure the safety belt systems are working properly after a crash, have them inspected and any necessary replacements made as soon as possible. After a minor crash, replacement of safety belts may not be necessary.
3-30 Seats and Restraints All of the airbags in the vehicle will have the word AIRBAG embossed in the trim or on an attached label near the deployment opening. For frontal airbags, the word AIRBAG will appear on the middle part of the steering wheel for the driver and on the instrument panel for the right front passenger. With seat-mounted side impact airbags, the word AIRBAG will appear on the side of the seatback closest to the door.
Seats and Restraints Where Are the Airbags? { WARNING Children who are up against, or very close to, any airbag when it inflates can be seriously injured or killed. Airbags plus lap-shoulder belts offer protection for adults and older children, but not for young children and infants. Neither the vehicle's safety belt system nor its airbag system is designed for them. Young children and infants need the protection that a child restraint system can provide. Always secure children properly in your vehicle.
3-32 Seats and Restraints The right front passenger frontal airbag is in the instrument panel on the passenger side. Driver Side shown, Passenger Side similar The seat-mounted side impact airbags for the driver and right front passenger are in the side of the seatbacks closest to the door.
Seats and Restraints { WARNING If something is between an occupant and an airbag, the airbag might not inflate properly or it might force the object into that person causing severe injury or even death. The path of an inflating airbag must be kept clear. Do not put anything between an occupant and an airbag, and do not attach or put anything on the steering wheel hub or on or near any other airbag covering. Do not use seat accessories that block the inflation path of a seat-mounted side impact airbag.
3-34 Seats and Restraints Frontal airbags are not intended to inflate during vehicle rollovers, rear impacts, or in many side impacts. the system's designed threshold level. The threshold level can vary with specific vehicle design. In addition, the vehicle has dual-stage frontal airbags. Dual-stage airbags adjust the restraint according to crash severity.
Seats and Restraints How Does an Airbag Restrain? In moderate to severe frontal or near frontal collisions, even belted occupants can contact the steering wheel or the instrument panel. In moderate to severe side collisions, even belted occupants can contact the inside of the vehicle. Airbags supplement the protection provided by safety belts. Frontal airbags distribute the force of the impact more evenly over the occupant's upper body, stopping the occupant more gradually.
3-36 Seats and Restraints Airbag inflation does not prevent the driver from seeing out of the windshield or being able to steer the vehicle, nor does it prevent people from leaving the vehicle. { WARNING When an airbag inflates, there may be dust in the air. This dust could cause breathing problems for people with a history of asthma or other breathing trouble. To avoid this, everyone in the vehicle should get out as soon as it is safe to do so.
Seats and Restraints . The vehicle has a crash sensing and diagnostic module which records information after a crash. See Vehicle Data Recording and Privacy on page 13‑15 and Event Data Recorders on page 13‑15. . Let only qualified technicians work on the airbag systems. Improper service can mean that an airbag system will not work properly. See your dealer/retailer for service. Passenger Sensing System The vehicle has a passenger sensing system for the right front passenger position.
3-38 Seats and Restraints We recommend that children be secured in a rear seat, including: an infant or a child riding in a rear-facing child restraint; a child riding in a forward-facing child seat; an older child riding in a booster seat; and children, who are large enough, using safety belts. A label on the sun visor says, “Never put a rear-facing child seat in the front.” This is because the risk to the rear-facing child is so great, if the airbag deploys.
Seats and Restraints The passenger sensing system is designed to turn on (may inflate) the right front passenger frontal airbag anytime the system senses that a person of adult size is sitting properly in the right front passenger seat. When the passenger sensing system has allowed the airbag to be enabled, the on indicator will light and stay lit to remind you that the airbag is active.
3-40 Seats and Restraints 5. If, after reinstalling the child restraint and restarting the vehicle, the on indicator is still lit, turn the vehicle off. Then slightly recline the vehicle seatback and adjust the seat cushion, if adjustable, to make sure that the vehicle seatback is not pushing the child restraint into the seat cushion. Also make sure the child restraint is not trapped under the vehicle head restraint. If this happens, adjust the head restraint. See Head Restraints on page 3‑2. 6.
Seats and Restraints Additional Factors Affecting System Operation Safety belts help keep the passenger in position on the seat during vehicle maneuvers and braking, which helps the passenger sensing system maintain the passenger airbag status. See “Safety Belts” and “Child Restraints” in the Index for additional information about the importance of proper restraint use.
3-42 Seats and Restraints Servicing the Airbag-Equipped Vehicle Airbags affect how the vehicle should be serviced. There are parts of the airbag system in several places around the vehicle. Your dealer/retailer and the service manual have information about servicing the vehicle and the airbag system. To purchase a service manual, see Service Publications Ordering Information on page 13‑12.
Seats and Restraints This could either prevent proper deployment of the passenger airbag(s) or prevent the passenger sensing system from properly turning off the passenger airbag(s). See Passenger Sensing System on page 3‑37. If you have questions, call Customer Assistance. The phone numbers and addresses for Customer Assistance are in Step Two of the Customer Satisfaction Procedure in this manual.
3-44 Seats and Restraints Replacing Airbag System Parts After a Crash If an airbag inflates, you will need to replace airbag system parts. See your dealer/retailer for service. { WARNING If the airbag readiness light stays on after the vehicle is started or comes on when you are driving, the airbag system may not work properly. Have the vehicle serviced right away. See Airbag Readiness Light on page 5‑16 for more information. A crash can damage the airbag systems in your vehicle.
Seats and Restraints The manufacturer's instructions that come with the booster seat, state the weight and height limitations for that booster. Use a booster seat with a lap-shoulder belt until the child passes the below fit test: . . Sit all the way back on the seat. Do the knees bend at the seat edge? If yes, continue. If no, return to the booster seat. Buckle the lap-shoulder belt. Does the shoulder belt rest on the shoulder? If yes, continue. If no, try using the rear safety belt comfort guide.
3-46 Seats and Restraints In a crash, children who are not buckled up can strike other people who are buckled up, or can be thrown out of the vehicle. Older children need to use safety belts properly. WARNING (Continued) { WARNING Never do this. Never allow two children to wear the same safety belt. The safety belt can not properly spread the impact forces. In a crash, the two children can be crushed together and seriously injured. A safety belt must be used by only one person at a time.
Seats and Restraints Infants and Young Children Everyone in a vehicle needs protection! This includes infants and all other children. Neither the distance traveled nor the age and size of the traveler changes the need, for everyone, to use safety restraints. In fact, the law in every state in the United States and in every Canadian province says children up to some age must be restrained while in a vehicle.
3-48 Seats and Restraints { WARNING Never do this. Children who are up against, or very close to, any airbag when it inflates can be seriously injured or killed. Never put a rear-facing child restraint in the right front seat. Secure a rear-facing child restraint in a rear seat. It is also better to secure a forward-facing child restraint in a rear seat. If you must secure a forward-facing child restraint in the right front seat, always move the front passenger seat as far back as it will go.
Seats and Restraints The restraint manufacturer's instructions that come with the restraint state the weight and height limitations for a particular child restraint. In addition, there are many kinds of restraints available for children with special needs. { WARNING To reduce the risk of neck and head injury during a crash, infants need complete support. This is because an infant's neck is not fully developed and its head weighs so much compared with the rest of its body.
3-50 Seats and Restraints Securing an Add-On Child Restraint in the Vehicle { WARNING (B) Forward-Facing Child Seat A forward-facing child seat (B) provides restraint for the child's body with the harness. (C) Booster Seats A booster seat (C) is a child restraint designed to improve the fit of the vehicle's safety belt system. A booster seat can also help a child to see out the window. A child can be seriously injured or killed in a crash if the child restraint is not properly secured in the vehicle.
Seats and Restraints See Lower Anchors and Tethers for Children (LATCH System) on page 3‑53 for more information. Children can be endangered in a crash if the child restraint is not properly secured in the vehicle. When securing an add-on child restraint, refer to the instructions that come with the restraint which may be on the restraint itself or in a booklet, or both, and to this manual.
3-52 Seats and Restraints A label on the sun visor says, “Never put a rear-facing child restraint in the front.” This is because the risk to the rear-facing child is so great, if the airbag deploys. { WARNING A child in a rear-facing child restraint can be seriously injured or killed if the right front passenger airbag inflates. This is because the back of the rear-facing child restraint would be very close to the inflating airbag.
Seats and Restraints Lower Anchors and Tethers for Children (LATCH System) The LATCH system holds a child restraint during driving or in a crash. This system is designed to make installation of a child restraint easier. The LATCH system uses anchors in the vehicle and attachments on the child restraint that are made for use with the LATCH system.
3-54 Seats and Restraints Top Tether Anchor A top tether (A, C) anchors the top of the child restraint to the vehicle. A top tether anchor is built into the vehicle. The top tether attachment (B) on the child restraint connects to the top tether anchor in the vehicle in order to reduce the forward movement and rotation of the child restraint during driving or in a crash. Your child restraint may have a single tether (A) or a dual tether (C).
Seats and Restraints 3-55 To assist you in locating the lower anchors, each second row anchor position has a label, near the crease between the seatback and the seat cushion. Second Row — 60/40 Bench i (Top Tether Anchor): Seating positions with top tether anchors. j (Lower Anchor): Seating positions with two lower anchors. Third Row i (Top Tether Anchor): Seating positions with top tether anchors.
3-56 Seats and Restraints Accident statistics show that children are safer if they are restrained in the rear rather than the front seat. See Where to Put the Restraint on page 3‑51 for additional information. Securing a Child Restraint Designed for the LATCH System { WARNING Second Row — Bucket Shown, Bench Similar The top tether anchors are located at the bottom rear of the seatback for each seating position in the second row. Open the cover to access the anchors.
Seats and Restraints { WARNING WARNING (Continued) Do not attach more than one child restraint to a single anchor. Attaching more than one child restraint to a single anchor could cause the anchor or attachment to come loose or even break during a crash. A child or others could be injured. To reduce the risk of serious or fatal injuries during a crash, attach only one child restraint per anchor.
3-58 Seats and Restraints 2. If the child restraint manufacturer recommends that the top tether be attached, attach and tighten the top tether to the top tether anchor, if the vehicle has one. Refer to the child restraint instructions and the following steps: 2.3. Route, attach and tighten the top tether according to your child restraint instructions and the following instructions: 2.1. Find the top tether anchor. 2.2. If the anchor is covered, flip open the cover to expose the anchor.
Seats and Restraints 3-59 Replacing LATCH System Parts After a Crash { WARNING If the position you are using has a fixed headrest or head restraint and you are using a dual tether, route the tether around the headrest or head restraint. If the position you are using has a fixed headrest or head restraint and you are using a single tether, route the tether over the headrest or head restraint. 3. Push and pull the child restraint in different directions to be sure it is secure.
3-60 Seats and Restraints Securing Child Restraints (Rear Seat) When securing a child restraint in a rear seating position, study the instructions that came with the child restraint to make sure it is compatible with this vehicle. If the child restraint has the LATCH system, see Lower Anchors and Tethers for Children (LATCH System) on page 3‑53 for how and where to install the child restraint using LATCH.
Seats and Restraints 3-61 6. If the child restraint has a top tether, follow the child restraint manufacturer's instructions regarding the use of the top tether. See Lower Anchors and Tethers for Children (LATCH System) on page 3‑53 for more information. 7. Push and pull the child restraint in different directions to be sure it is secure. 4. Pull the rest of the shoulder belt all the way out of the retractor to set the lock. 5.
3-62 Seats and Restraints Securing Child Restraints (Right Front Passenger Seat) The vehicle has airbags. A rear seat is a safer place to secure a forward-facing child restraint. See Where to Put the Restraint on page 3‑51. In addition, the vehicle has a passenger sensing system which is designed to turn off the right front passenger frontal airbag under certain conditions.
Seats and Restraints Do not secure a child seat in a position without a top tether anchor if a national or local law requires that the top tether be anchored, or if the instructions that come with the child restraint say that the top strap must be anchored. In Canada, the law requires that forward-facing child restraints have a top tether, and that the tether be attached. 2. Put the child restraint on the seat. 3.
3-64 Seats and Restraints If the airbags are off, the off indicator in the passenger airbag status indicator will come on and stay on when the vehicle is started. If a child restraint has been installed and the on indicator is lit, see “If the On Indicator is Lit for a Child Restraint” under Passenger Sensing System on page 3‑37 for more information. 6.
Storage Storage Storage Compartments Instrument Panel Storage . . . . Glove Box . . . . . . . . . . . . . . . . . . . . Cupholders . . . . . . . . . . . . . . . . . . . Armrest Storage . . . . . . . . . . . . . . Center Console Storage . . . . . . Floor Console Storage . . . . . . . . 4-1 4-1 4-1 4-1 4-1 4-2 Additional Storage Features Cargo Cover . . . . . . . . . . . . . . . . . . Cargo Tie Downs . . . . . . . . . . . . . Cargo Management System . . . . . . . . . . . . . . . . . . . . . .
4-2 Storage To open the armrest storage area, press the button located on the front of the armrest. There is additional storage under the armrest. Move the armrest all the way to the rear position, slide the cover back and remove the tray. { WARNING Never open more than one of the three latches at a time to help avoid personal injury and damage to the console. Floor Console Storage To access the upper storage area, press the upper button (B) and lift up.
Storage Additional Storage Features WARNING (Continued) always store it outside of the vehicle. When it is replaced, always be sure that it is securely reattached. Cargo Cover For vehicles with a cargo cover, it can be used to cover items in the rear of the vehicle. To install the cover, place the loops on each corner of the cover on the four hooks in the rear of the vehicle. The cover should be stored securely when not in use.
4-4 Storage Roof Rack System { WARNING If something is carried on top of the vehicle that is longer or wider than the roof rack— like paneling, plywood, or a mattress— the wind can catch it while the vehicle is being driven. The item being carried could be violently torn off, and this could cause a collision, and damage the vehicle. Never carry something longer or wider than the roof rack on top of the vehicle unless using a GM Certified accessory carrier.
Instruments and Controls Instruments and Controls Controls Steering Wheel Adjustment . . . 5-2 Steering Wheel Controls . . . . . . 5-3 Horn . . . . . . . . . . . . . . . . . . . . . . . . . . 5-5 Windshield Wiper/Washer . . . . . 5-5 Rear Window Wiper/ Washer . . . . . . . . . . . . . . . . . . . . . . 5-6 Compass . . . . . . . . . . . . . . . . . . . . . 5-7 Clock . . . . . . . . . . . . . . . . . . . . . . . . . 5-9 Power Outlets . . . . . . . . . . . . . . .
5-2 Instruments and Controls Vehicle Personalization Vehicle Personalization . . . . . . 5-40 Universal Remote System Universal Remote System . . . 5-47 Universal Remote System Programming . . . . . . . . . . . . . . . 5-47 Universal Remote System Operation . . . . . . . . . . . . . . . . . . 5-51 Controls Do not adjust the steering wheel while driving. Steering Wheel Adjustment Power Tilt Wheel The steering wheel can be adjusted. The adjustment lever is on the outboard side of the steering column.
Instruments and Controls Push the control forward or rearward to move the steering wheel toward the front or rear of the vehicle. To set the memory position, see Vehicle Personalization on page 5‑40. w / x (Next / Previous): Steering Wheel Controls To select preset or favorite radio stations: Press to select preset or favorite radio stations, select tracks on a CD/ DVD, or to select tracks and navigate folders on an iPod® or USB device. .
5-4 Instruments and Controls To navigate folders on an iPod or USB device for vehicles without a navigation system: To navigate folders on an iPod or USB device for vehicles with a navigation system: b g (Mute/Push to Talk): Press to silence the vehicle speakers only. Press again to turn the sound on. 1. Press and hold w or x while listening to a song until the contents of the current folder display on the radio display. 1.
Instruments and Controls SRCE (Source/Voice Recognition): Press to switch between the radio, CD, and for vehicles with, DVD, front auxiliary, and rear auxiliary. For vehicles with the navigation system, press and hold this button for longer than one second to initiate voice recognition. See “Voice Recognition” in the Navigation System manual for more information. For vehicles with a navigation system: 1.
5-6 Instruments and Controls 6 (Adjustable Interval Wipes): Turn the band up for more frequent wipes or down for less frequent wipes. 1 : Slow wipes. 2 : Fast wipes. Clear ice and snow from the wiper blades before using them. If frozen to the windshield, carefully loosen or thaw them. Damaged wiper blades should be replaced. See Wiper Blade Replacement on page 10‑26. Heavy snow or ice can overload the wipers. A circuit breaker stops them until the motor cools.
Instruments and Controls Compass Your vehicle may have a compass in the Driver Information Center (DIC). See Driver Information Center (DIC) on page 5‑25 for more information about the DIC. Compass Zone Compass variance is the difference between the earth's magnetic north and true geographic north. If the compass is not set to the zone where you live, the compass may give false readings. The compass must be set to the variance zone in which the vehicle is traveling.
5-8 Instruments and Controls 4. Press the trip/fuel button until the vehicle heading, for example, N for North, is displayed in the DIC. 5. If calibration is necessary, calibrate the compass. See “Compass Calibration Procedure” following. Compass Calibration The compass can be manually calibrated. Only calibrate the compass in a magnetically clean and safe location, such as an open parking lot, where driving the vehicle in circles is not a danger.
Instruments and Controls Clock The vehicle has an analog clock and a digital radio clock. The digital radio clock can be enabled or disabled. Setting the Analog Clock The analog clock is located on the instrument panel above the radio. The clock is not connected with any other vehicle system and runs by itself. To adjust the time: 1. Push and hold the button located directly above the clock to advance the clock hands. Holding the button down causes the clock to advance faster. 2.
5-10 Instruments and Controls 3. Press the pushbutton located under any one of the labels to be changed. 4. To increase the time or date, do one of the following: . . . . Press the pushbutton below the selected label. ¨ SEEK. Press \ FWD. Turn f clockwise. Press 5. To decrease the time or date, do one of the following: . . . © SEEK. Press s REV. Turn f counter‐clockwise.
Instruments and Controls Certain accessory plugs may not be compatible to the accessory power outlet and could result in blown vehicle and adapter fuses. If a problem is experienced, see your dealer/retailer for additional information on the power accessory outlets. Notice: Adding any electrical equipment to the vehicle can damage it or keep other components from working as they should. The repairs would not be covered by the vehicle warranty.
5-12 Instruments and Controls If equipment is connected using more than 150 watts or a system fault is detected, a protection circuit shuts off the power supply and the indicator light turns off. To reset the circuit, unplug the item and plug it back in or turn the Remote Accessory Power (RAP) off and then back on. See Retained Accessory Power (RAP) on page 9‑19. The power restarts when equipment using 150 watts or less is plugged into the outlet and a system fault is not detected.
Instruments and Controls Instrument Cluster United States version shown, Canada similar 5-13
5-14 Instruments and Controls Speedometer The speedometer shows the vehicle's speed in both kilometers per hour (km/h) and miles per hour (mph). Odometer be damaged, and the damages would not be covered by the vehicle warranty. Do not operate the engine with the tachometer in the shaded warning area. Fuel Gauge Here are some situations that can occur with the fuel gauge. None of these indicate a problem with the fuel gauge.
Instruments and Controls Engine Coolant Temperature Gauge United States Canada This gauge shows the engine coolant temperature. Under normal driving conditions the gauge will read 210°F (100 °C) or less. If the gauge pointer is near 260°F (125 °C), the engine is too hot. It means that the engine coolant has overheated. If the vehicle has been operating under normal driving conditions, pull off the road, stop the vehicle and turn off the engine as soon as possible.
5-16 Instruments and Controls Safety Belt Reminders Driver Safety Belt Reminder Light Passenger Safety Belt Reminder Light The driver safety belt reminder light on the instrument panel cluster. as a briefcase, handbag, grocery bag, laptop or other electronic device. To turn off the warning light and or chime, remove the object from the seat or buckle the safety belt.
Instruments and Controls If the airbag readiness light stays on after the vehicle has been started or comes on when while driving, the airbag system may not work properly. Have the vehicle serviced right away. { WARNING If the airbag readiness light stays on after the vehicle is started or comes on while driving, it means the airbag system might not be working properly. The airbags in the vehicle might not inflate in a crash, or they could even inflate without a crash.
5-18 Instruments and Controls If, after several seconds, both status indicator lights remain on, or if there are no lights at all, there may be a problem with the lights or the passenger sensing system. See your dealer/retailer for service. { WARNING If the airbag readiness light ever comes on and stays on, it means that something may be wrong with the airbag system. To help avoid injury to yourself or others, have the vehicle serviced right away.
Instruments and Controls Malfunction Indicator Lamp A computer system called OBD II (On-Board Diagnostics-Second Generation) monitors operation of the fuel, ignition, and emission control systems. It ensures that emissions are at acceptable levels for the life of the vehicle, helping to produce a cleaner environment. This light comes on when the ignition is on, but the engine is not running, as a check to show it is working. If it does not, have the vehicle serviced by your dealer/ retailer.
5-20 Instruments and Controls The following can prevent more serious damage to the vehicle: . Reduce vehicle speed. . Avoid hard accelerations. . Avoid steep uphill grades. . If towing a trailer, reduce the amount of cargo being hauled as soon as it is possible. If the light continues to flash, when it is safe to do so, stop the vehicle. Find a safe place to park the vehicle. Turn the key off, wait at least 10 seconds, and restart the engine.
Instruments and Controls Emissions Inspection and Maintenance Programs Some state/provincial and local governments have or might begin programs to inspect the emission control equipment on the vehicle. Failure to pass this inspection could prevent getting a vehicle registration. Here are some things to know to help the vehicle pass an inspection: . The vehicle will not pass this inspection if the check engine light is on with the engine running, or if the key is in ON/ RUN and the light is not on. .
5-22 Instruments and Controls When the ignition is on, the brake system warning light will also come on when the parking brake is set. The light will stay on if the parking brake does not release fully. If it stays on after the parking brake is fully released, it means there is a brake problem. If the light comes on while driving, pull off the road and stop carefully. Make sure the parking brake is fully released. The pedal may be harder to push or, the pedal may go closer to the floor.
Instruments and Controls StabiliTrak® Indicator Light This light comes on briefly while starting the engine. If it does not, have the vehicle serviced by your dealer/retailer. If the system is working normally the indicator light goes off. If it stays on, or comes on while driving, there could be a problem with the StabiliTrak system and the vehicle might need service. When this warning light is on, the system is off and will not limit wheel spin. This light flashes when the StabiliTrak system is active.
5-24 Instruments and Controls loading information label. See Tire Pressure on page 10‑44 for more information. When the Light Flashes First and Then is On Steady This indicates that there may be a problem with the Tire Pressure Monitor System. The light flashes for about a minute and stays on steady for the remainder of the ignition cycle. This sequence repeats with every ignition cycle. See Tire Pressure Monitor Operation on page 10‑46 for more information.
Instruments and Controls Fog Lamp Light Cruise Control Light 5-25 Information Displays Driver Information Center (DIC) Your vehicle has a Driver Information Center (DIC). The fog lamp light comes on when the fog lamps are in use. This light comes on whenever the cruise control is set. The light goes out when the fog lamps are turned off. See Fog Lamps on page 6‑5 for more information. The light goes out when the cruise control is turned off. See Cruise Control on page 9‑32 for more information.
5-26 Instruments and Controls The outside air temperature and compass, if equipped, also display on the DIC when viewing the trip and fuel information. The outside air temperature automatically appears in the top right corner of the DIC display. If there is a problem with the system that controls the temperature display, the numbers will be replaced with dashes. If this occurs, have the vehicle serviced. The compass will be shown in the bottom right corner of the DIC display.
Instruments and Controls When the remaining oil life is low, the CHANGE ENGINE OIL SOON message will appear on the display. See “CHANGE ENGINE OIL SOON” under Engine Oil Messages on page 5‑34. You should change the oil as soon as you can. See Engine Oil on page 10‑8. In addition to the engine oil life system monitoring the oil life, additional maintenance is recommended in the Maintenance Schedule in this manual. See Scheduled Maintenance on page 11‑2 for more information.
5-28 Instruments and Controls If a low tire pressure condition is detected by the system while driving, a message advising you add air to a specific tire will appear in the display. See Tire Pressure on page 10‑44 and Tire Messages on page 5‑37 for more information. If the tire pressure display shows dashes instead of a value, there may be a problem with your vehicle. If this consistently occurs, see your dealer/retailer for service.
Instruments and Controls To switch between English and metric measurements, see “UNITS” earlier in this section. TRIP A and TRIP B Press the trip/fuel button until TRIP A or TRIP B displays. This display shows the current distance traveled in either miles (mi) or kilometers (km) since the last reset for each trip odometer. Both trip odometers can be used at the same time. Each trip odometer can be reset to zero separately by pressing the set/ reset button while the desired trip odometer is displayed.
5-30 Instruments and Controls AVG (Average) ECONOMY Press the trip/fuel button until AVG ECONOMY displays. This display shows the approximate average miles per gallon (mpg) or liters per 100 kilometers (L/100 km). This number is calculated based on the number of mpg (L/100 km) recorded since the last time this menu item was reset. To reset AVG ECONOMY, press and hold the set/ reset button. TIMER Press the trip/fuel button until TIMER displays. This display can be used as a timer.
Instruments and Controls Vehicle Messages Messages are displayed on the DIC to notify the driver that the status of the vehicle has changed and that some action may be needed by the driver to correct the condition. Multiple messages may appear one after another. Some messages may not require immediate action, but you can press any of the DIC buttons on the instrument panel to acknowledge that you received the messages and to clear them from the display.
5-32 Instruments and Controls Brake System Messages Door Ajar Messages SERVICE BRAKE SYSTEM DRIVER DOOR OPEN This message displays along with the brake system warning light if there is a problem with the brake system. See Brake System Warning Light on page 5‑21. If this message appears, stop as soon as possible and turn off the vehicle. Restart the vehicle and check for the message on the DIC display.
Instruments and Controls RIGHT REAR DOOR OPEN This message displays and a chime sounds if the passenger side rear door is not fully closed and the vehicle is shifted out of P (Park). Stop and turn off the vehicle, check the door for obstructions, and close the door again. Check to see if the message still appears on the DIC. Engine Cooling System Messages ENGINE HOT A/C (Air Conditioning) OFF This message displays when the engine coolant becomes hotter than the normal operating temperature.
5-34 Instruments and Controls Engine Oil Messages CHANGE ENGINE OIL SOON This message displays when the engine oil needs to be changed. When you change the engine oil, be sure to reset the CHANGE ENGINE OIL SOON message. See Engine Oil Life System on page 10‑10 for information on how to reset the message. See Engine Oil on page 10‑8 and Scheduled Maintenance on page 11‑2 for more information.
Instruments and Controls 5-35 TIGHTEN GAS CAP Key and Lock Messages Lamp Messages This message may display along with the check engine light on the instrument panel cluster if the vehicle's fuel cap is not tightened properly. See Malfunction Indicator Lamp on page 5‑19. Reinstall the fuel cap fully. See Filling the Tank on page 9‑45. The diagnostic system can determine if the fuel cap has been left off or improperly installed. A loose or missing fuel cap allows fuel to evaporate into the atmosphere.
5-36 Instruments and Controls Object Detection System Messages Ride Control System Messages retailer for service. See StabiliTrak System on page 9‑30 for more information.
Instruments and Controls Anti-Theft Alarm System Messages SERVICE THEFT DETERRENT SYSTEM This message displays when there is a problem with the theft-deterrent system. The vehicle may or may not restart so you may want to take the vehicle to your dealer/retailer before turning off the engine. See Immobilizer Operation on page 2‑13 for more information. THEFT ATTEMPTED This message displays if the content theft-deterrent system has detected a break-in attempt while you were away from your vehicle.
5-38 Instruments and Controls This message also displays LEFT FRT (left front), RIGHT FRT (right front), LEFT RR (left rear), or RIGHT RR (right rear) to indicate the location of the low tire. The low tire pressure warning light will also come on. See Tire Pressure Light on page 5‑23. If a tire pressure message appears on the DIC, stop as soon as you can. Inflate the tires by adding air until the tire pressure is equal to the values shown on the Tire Loading Information label.
Instruments and Controls SERVICE ALL WHEEL DRIVE If your vehicle has the All-Wheel Drive (AWD) system, this message displays if there is a problem with this system. If this message appears, stop as soon as possible and turn off the vehicle. Restart the vehicle after 30 seconds and check for the message on the DIC display. If the message is still displayed or appears again when you begin driving, the AWD system needs service. See your dealer/retailer.
5-40 Instruments and Controls Vehicle Personalization Your vehicle may have customization capabilities that allow you to program certain features to one preferred setting. Customization features can only be programmed to one setting on the vehicle and cannot be programmed to a preferred setting for two different drivers. All of the customization options may not be available on your vehicle. Only the options available will be displayed on the DIC.
Instruments and Controls NO CHANGE: No change will be made to this feature. The current setting will remain. To select a setting, press the set/ reset button while the desired setting is displayed on the DIC. AUTO DOOR LOCK This feature allows you to select when the vehicle's doors will automatically lock. See Automatic Door Locks on page 2‑8 for more information. Press the customization button until AUTO DOOR LOCK appears on the DIC display.
5-42 Instruments and Controls To select a setting, press the set/ reset button while the desired setting is displayed on the DIC. LIGHTS ONLY: The exterior lamps will flash when you press the lock button on the RKE transmitter. REMOTE DOOR LOCK HORN ONLY: The horn will sound on the second press of the lock button on the RKE transmitter. This feature allows you to select the type of feedback you will receive when locking the vehicle with the Remote Keyless Entry (RKE) transmitter.
Instruments and Controls DELAY DOOR LOCK This feature allows you to select whether or not the locking of the vehicle's doors and liftgate will be delayed. When locking the doors and liftgate with the power door lock switch and a door or the liftgate is open, this feature will delay locking the doors and liftgate until five seconds after the last door is closed. You will hear three chimes to signal that the delayed locking feature is in use. The key must be out of the ignition for this feature to work.
5-44 Instruments and Controls APPROACH LIGHTING This feature allows you to select whether or not to have the exterior lights turn on briefly during low light periods after unlocking the vehicle using the Remote Keyless Entry (RKE) transmitter. Press the customization button until APPROACH LIGHTING appears on the DIC display. Press the set/reset button once to access the settings for this feature.
Instruments and Controls for this feature. Then press the customization button to scroll through the following settings: OFF (default): Neither outside mirror will be tilted down when the vehicle is shifted into R (Reverse). DRIVER MIRROR: The driver's outside mirror will be tilted down when the vehicle is shifted into R (Reverse). PASSENGER MIRROR: The passenger's outside mirror will be tilted down when the vehicle is shifted into R (Reverse).
5-46 Instruments and Controls Press the customization button until MEMORY SEAT RECALL appears on the DIC display. Press the set/ reset button once to access the settings for this feature. Then press the customization button to scroll through the following settings: OFF (default): No remote memory seat recall will occur. ON: The driver's seat and outside mirrors will automatically move to the stored driving position when the unlock button on the Remote Keyless Entry (RKE) transmitter is pressed.
Instruments and Controls To select a setting, press the set/ reset button while the desired setting is displayed on the DIC. EXIT FEATURE SETTINGS This feature allows you to exit the feature settings menu. Press the customization button until FEATURE SETTINGS PRESS V TO EXIT appears in the DIC display. Press the set/reset button once to exit the menu. If you do not exit, pressing the customization button again will return you to the beginning of the feature settings menu.
5-48 Instruments and Controls Do not use the Universal Home Remote with any garage door opener that does not have the stop and reverse feature. This includes any garage door opener model manufactured before April 1, 1982. Read the instructions completely before attempting to program the Universal Home Remote. Because of the steps involved, it may be helpful to have another person available to assist you with programming the Universal Home Remote.
Instruments and Controls 2. Hold the end of your hand-held transmitter about 3 to 8 cm (1 to 3 inches) away from the Universal Home Remote buttons while keeping the indicator light in view. The hand-held transmitter was supplied by the manufacturer of your garage door opener receiver (motor head unit). 3. At the same time, press and hold both the Universal Home Remote button to be used to control the garage door and the hand-held transmitter button.
5-50 Instruments and Controls 7. Firmly press and release the “Learn” or “Smart” button. After you press this button, you will have 30 seconds to complete Step 8. 8. Immediately return to the vehicle. Firmly press and hold the Universal Home Remote button, selected in Step 3 to control the garage door, for two seconds, and then release it. If the garage door does not move, press and hold the same button a second time for two seconds, and then release it.
Instruments and Controls Universal Remote System Operation To erase all programmed buttons on the Universal Remote device: Reprogramming a Single Universal Remote Button To reprogram any of the three Universal Remote buttons, repeat the programming instructions earlier in this section, beginning with Step 2. Using Universal Remote Press and hold the appropriate Universal Remote button for at least half of a second. The indicator light will come on while the signal is being transmitted.
5-52 Instruments and Controls 2 NOTES
Lighting Lighting Exterior Lighting Exterior Lamp Controls . . . . . . . . 6-1 Headlamp High/Low-Beam Changer . . . . . . . . . . . . . . . . . . . . . 6-2 Flash-to-Pass . . . . . . . . . . . . . . . . . 6-3 Daytime Running Lamps (DRL)/Automatic Headlamp System . . . . . . . . . . . . . . . . . . . . . . 6-3 Delayed Headlamps . . . . . . . . . . 6-3 Adaptive Forward Lighting (AFL) . . . . . . . . . . . . . . . 6-4 Hazard Warning Flashers . . . . . 6-4 Turn and Lane-Change Signals . . . . . . . . . . . . .
6-2 Lighting It controls the following systems: ;(Parking Lamps): Turns the parking lamps on together with the following: . Headlamps . Taillamps . . Parking Lamps Taillamps . . License Plate Lamps License Plate Lamps . . Instrument Panel Lights Instrument Panel Lights . Fog Lamps The exterior lamps control has four positions: 9 (Off): Briefly turn to this position to turn the automatic light control off or on again.
Lighting Flash-to-Pass This feature is used to signal to the vehicle ahead that you want to pass. If the headlamps are off or in the low‐beam position, pull the turn signal lever toward you to momentarily switch to high‐beams. Release the lever to turn the high-beam headlamps off. Daytime Running Lamps (DRL)/Automatic Headlamp System Daytime Running Lamps (DRL) can make it easier for others to see the front of your vehicle during the day.
6-4 Lighting Adaptive Forward Lighting (AFL) Vehicles with the Adaptive Forward Lighting System (AFS) have headlamps that swivel to the left or right when making a turn to provide better lighting. To enable AFS, set the exterior lamp switch to the AUTO position. Move the switch out of the AUTO position to turn off the system. See Exterior Lamp Controls on page 6‑1. turn signal lamps flash on and off. This warns others that you are having trouble. Press again to turn the flashers off.
Lighting Fog Lamps Use the fog lamps for better vision in foggy or misty conditions. The fog lamps button is on the exterior lamps control to the left of the steering column. # (Fog Lamps): Press the exterior lamps button to turn the fog lamps on or off. A light comes on in the instrument panel cluster when the fog lamps are in use. The ignition must be on for the fog lamps to work. When the headlamps are changed to high-beam, the fog lamps turn off.
6-6 Lighting Lighting Features Entry Lighting For vehicles with courtesy lamps, they come on and stay on for a set time whenever the unlock symbol is pressed on the Remote Keyless Entry (RKE) transmitter, if the vehicle has one. If a door is opened, the lamps stay on while it is open and then turn off automatically about 20 seconds after the door is closed. If the unlock symbol is pressed and no door is opened, the lamps turn off after about 20 seconds.
Lighting Parade Dimming This feature automatically prohibits the dimming of the instrument panel displays in daylight while the headlamps are on so that the displays are still able to be seen. Battery Load Management The vehicle has Electric Power Management (EPM) that estimates the battery's temperature and state of charge. It then adjusts the voltage for best performance and extended life of the battery.
6-8 Lighting Battery Power Protection This feature helps prevent the battery from being drained, if the interior courtesy lamps, reading/map lamps, visor vanity lamps or trunk lamp are accidentally left on. If any of these lamps are left on, they automatically turn off after 10 minutes, if the ignition is off. The lamps will not come back on again until one of the following occurs: . The ignition is turned on. . The exterior lamps control is turned off, then on again.
Infotainment System Infotainment System Introduction Introduction . . . . . . . . . . . . . . . . . . . 7-1 Theft-Deterrent Feature . . . . . . . 7-2 Operation . . . . . . . . . . . . . . . . . . . . . 7-2 Radio AM-FM Radio . . . . . . . . . . . . . . . . . 7-6 Satellite Radio . . . . . . . . . . . . . . . . 7-8 Radio Reception . . . . . . . . . . . . . 7-11 Multi-Band Antenna . . . . . . . . . . 7-12 Audio Players CD Player . . . . . . . . . . . . . . . . . . . CD/DVD Player . . . . . . . . . . . . . .
7-2 Infotainment System For more information, see Defensive Driving on page 9‑2. Operation The vehicle has Retained Accessory Power (RAP). With RAP, the audio system can be played even after the ignition is turned off. See Retained Accessory Power (RAP) on page 9‑19 for more information. Navigation/Radio System For vehicles with a navigation radio system, see the separate Navigation System manual.
Infotainment System 7-3 See Rear Seat Entertainment (RSE) System on page 7‑36 for more information on the vehicle's RSE system. The DVD player is the top slot on the radio faceplate. The player is capable of reading the DTS programmed DVD Audio or DVD Video media. DTS and DTS Digital Surround are registered trademarks of Digital Theater Systems, Inc.. Manufactured under license from Dolby Laboratories. Dolby and the double-D symbol are trademarks of Dolby Laboratories.
7-4 Infotainment System Parental control prevents the rear seat occupant from operating the Rear Seat Audio (RSA) system or remote control. information displays on the bottom line. When information is not available, “NO INFO” is displayed. A lock symbol displays next to the clock display while the parental control feature is being used. The feature remains on until O is pressed and held for more than two seconds, or the driver turns the ignition off and exits the vehicle.
Infotainment System Each higher setting allows for more radio volume compensation at faster vehicle speeds. Setting the Tone (Bass/Midrange/Treble) BASS/MID/TREB (Bass, Midrange, or Treble): To adjust bass, midrange, or treble: 1. Press f until the tone control tabs display. 2. Continue pressing f to highlight the tab, or press the softkey under the tab. 3. To adjust the highlighted setting, do one of the following until the levels are obtained.
7-6 Infotainment System To quickly adjust all speaker and tone controls to the middle position, press f for more than two seconds until a beep sounds. Radios with CD and DVD fade differently depending on the DVD Media type: . . With DVD‐A 5.1 Surround media, the left front and right front speakers fade rearward, leaving the center front speakers unaffected until the last fade step, then all front speakers mute. With DVD‐V 5.
Infotainment System © SEEK ¨ : Press to go to the previous or to the next station and stay there. To scan stations, press and hold © or ¨ until a beep sounds. The radio goes to a station, plays for a few seconds, then goes to the next station. Press either arrow again to stop scanning. The radio only seeks and scans stations with a strong signal that are in the selected band.
7-8 Infotainment System Satellite Radio XM™ Satellite Radio Service XM is a satellite radio service that is based in the 48 contiguous United States and 10 Canadian provinces. XM Satellite Radio has a wide variety of programming and commercial-free music, coast-to-coast, and in digital-quality sound. For more information, contact XM at www.xmradio.com or call 1-800-929-2100 in the U.S. and www.xmradio.ca or call 1-877-438-9677 in Canada. Finding a Station BAND: Press to switch between AM, FM, or XM.
Infotainment System Undesired XM categories can be removed through the setup menu. To remove an undesired category, perform the following: 1. Press MENU to display the radio setup menu. 2. Press the softkey below the XM CAT tab. 3. Turn f to display the category to be removed. 4. Press the softkey under the Remove tab until the category name along with the word Removed displays. 5. Repeat the steps to remove more categories.
7-10 Infotainment System 4. Press FAV, or let the menu time out, to return to the original main radio screen showing the radio station frequency tabs and to begin the process of programming favorites for the chosen amount of numbered pages. XM™ Radio Messages XL (Explicit Language Channels): These channels, or any others, can be blocked at a customer's request, by calling 1-800-852-XMXM (9696). XM Updating: The encryption code in the receiver is being updated, and no action is required.
Infotainment System Unknown: If this message is received when tuned to channel 0, there could be a receiver fault. Consult with your dealer/retailer. Check XM Receivr: If this message does not clear within a short period of time, the receiver could have a fault. Consult with your dealer/retailer. XM Not Available: If this message does not clear within a short period of time, the receiver could have a fault. Consult with your dealer/ retailer.
7-12 Infotainment System Multi-Band Antenna The multi-band antenna is located on the roof of the vehicle. This type of antenna is used with the AM/FM radio, as well as OnStar® and the XM™ Satellite Radio Service System, if the vehicle has these features. Keep this antenna clear of snow and ice build up for clear radio reception. If the vehicle has a sunroof, the performance of the radio system may be affected if the sunroof is open.
Infotainment System BAND: Press to listen to the radio when a CD is playing. The CD remains inside the radio for future listening. CD/AUX (CD/Auxiliary): Press to select between CD, or Auxiliary. . . When a CD is in the player the CD icon and a message showing the disc and/or track number displays. If an auxiliary input device is not connected, “No Input Device Found” displays.
7-14 Infotainment System CD Messages CHECK DISC: Radios with a Single CD player display CHECK DISC and/or ejects the CD if an error occurs. Optical Error: The disc was inserted upside down. Disk Read Error: A disc was inserted with an invalid or unknown format. Player Error: There are disc LOAD or disc EJECT problems. . It is very hot. When the temperature returns to normal, the CD should play. . The road is very rough. When the road becomes smoother, the CD should play. .
Infotainment System If the disc is not removed, after several seconds, the disc automatically pulls back into the player. Z DVD (Eject): Press and release to eject the disc that is currently playing in the top slot. A beep sounds and Ejecting Disc displays. If loading and reading of a disc cannot be completed, and the disc fails to eject, press and hold Z DVD for more than five seconds to force the disc to eject. f (Tune): Turn to select tracks on the CD that is currently playing.
7-16 Infotainment System If a disc is inserted into the top DVD slot, the rear seat operator can turn on the video screen and use the remote control to only navigate the CD tracks through the remote control. See “Using the Auxiliary Input Jack(s)” later in this section, or “Audio/Video (A/V) Jacks” under, Rear Seat Entertainment (RSE) System on page 7‑36 for more information.
Infotainment System Front seat passengers can listen to the radio (AM, FM, or XM) by pressing BAND or DVD/CD AUX to select the CD slot, DVD slot, front or rear auxiliary input (if available). If a playback device is plugged into the radio’s front auxiliary input jack or the rear auxiliary jack, the front seat passengers are able to listen to playback from this source through the vehicle speakers.
7-18 Infotainment System Using the DVD Player Playing a DVD The DVD player can be controlled by the buttons on the remote control, the RSA system, or by the buttons on the radio faceplate. See “Remote Control”, under Rear Seat Entertainment (RSE) System on page 7‑36 and Rear Seat Audio (RSA) System on page 7‑44 for more information. f (Tune): The DVD player is only compatible with DVDs of the appropriate region code that is printed on the jacket of most DVDs.
Infotainment System If loading and reading of a DVD cannot be completed, because of an unknown format, etc., and the disc fails to eject, press and hold for more than five seconds to force the disc to eject. r / j (Play/Pause): Press either the play or pause icon displayed on the radio system, to toggle between pausing or restarting playback of a DVD. . If the forward arrow is showing on display, the system is in pause mode. . If the pause icon is showing on display, the system is in playback mode. .
7-20 Infotainment System DVD-A (Audio) Display Buttons Once a DVD-A is inserted, the radio display menu shows several icons. Press the softkeys under any icon during DVD playback. See the icon list below for more information. The rear seat operator can navigate the DVD-A menus and controls through the remote control. See “Remote Control”, under Rear Seat Entertainment (RSE) System on page 7‑36 for more information.
Infotainment System To resume DVD playback, do one of the following: . Press r / control. j on the remote . Press the softkey under the play/pause icon displayed on the radio. The DVD should resume play from where it last stopped if the disc has not been ejected and the stop button has not been pressed twice on the remote control. If the disc has been ejected or the stop button has been pressed twice on the remote control, the disc resumes playing at the beginning of the disc.
7-22 Infotainment System Compressed Audio or Mixed Mode Discs USB Supported File and Folder Structure The radio can play discs that contain both uncompressed CD audio and MP3/WMA files. If both formats are on the disc, the radio plays both file formats in the order in which they were recorded to the disc. The radio supports: CD‐R or CD‐RW Supported File and Folder Structure The radio supports: . Up to 700 folders. . Up to 8 folders in depth.
Infotainment System Tracks are played in the following order: . . Play begins from the first track in the first playlist and continues sequentially through all tracks in each playlist. When the last track of the last playlist has played, play continues from the first track of the first playlist. Play begins from the first track in the first folder and continues sequentially through all tracks in each folder.
7-24 Infotainment System S c (Previous Folder): Press the softkey below S c to go to the first track in the previous folder. c T (Next Folder): Press the softkey below c T to go to the first track in the next folder. RDM (Random): Files on the disc can be listened to in random, rather than sequential order. To use random, press the softkey under the RDM tab until Random Current Disc displays to play songs in random order. Press the same softkey again to turn off random play.
Infotainment System To connect an iPod, connect one end of the USB cable that came with the iPod to the iPod’s dock connector and connect the other end to the USB port located in the center console. If the vehicle is on and the USB connection works, “OK to disconnect” and a GM logo may appear on the iPod and iPod appears on the radio's display. The iPod music appears on the radio’s display and begins playing.
7-26 Infotainment System j (Pause): Press the softkey below j to pause the track. The tab appears raised when pause is being used. Press the softkey below j again to resume playback. Back: Press the softkey below the back tab to go back to the main display screen on an iPod, or the root directory on a USB storage device. c (Folder View): Press the softkey below c to view the contents of the current folder on the USB drive. To browse and select files: 1. Press the softkey below 4.
Infotainment System To skip through large lists, the five softkeys can be used to navigate in the following order: ' (Repeat Track): Press the softkey below ' to repeat one track. The tab appears raised when Repeat Track is being used. . First softkey, first item in the list. . Second softkey, 1% through the list each time the softkey is pressed. Shuffle Functionality . Third softkey, 5% through the list each time the softkey is pressed. Press the softkey below >, 2, < or = to select .
7-28 Infotainment System The CD Player reads both uncompressed audio and MP3/WMA files on a mixed mode disc. Uncompressd audio is played before MP3/WMA files. Press the CAT (category) button to toggle between uncompressed audio and MP3/WMA files. CD‐R or CD‐RW Supported File and Folder Structure The DVD Player supports: . Up to 255 folders. . Up to 8 folders in depth. . Up to 15 playlists. . Up to 40 sessions. . Playlists with an .m3u or .wpl extension. . Files with an .mp3, .wma, or .
Infotainment System The folder down and the folder up buttons search playlists first and then goes to the root folder. When the radio displays the name of the folder the radio displays ROOT. Order of Play Compressed audio files are accessed in the following order: . Playlists. . Files stored in the root directory. . Files stored in folders in the root directory. Tracks are played in the following order: .
7-30 Infotainment System Playing an MP3/WMA File From a Disc (In Either the DVD or CD Slot) If a disc is inserted into the top DVD slot, the rear seat operator can turn on the video screen and use the remote control to navigate the CD (tracks only). f (Tune): Turn to select MP3/WMA files. © SEEK: Press to go to the start of the track, if more than five seconds have played. Press to go to the previous track if more then five seconds have played.
Infotainment System To listen to files by another artist, press the softkey located below either arrow tab. The disc goes to the next or previous artist in alphabetical order. Continue pressing either softkey below the arrow tab until the artist displays. To change from playback by artist to playback by album: 1. Press the softkey located below the Sort By tab. 2. Press one of the softkeys below the album tab from the sort screen. 3.
7-32 Infotainment System Using the Radio to Control a USB Storage Device or iPod The radio can control a USB storage device or an iPod using the radio buttons and knobs and display song information on the radio’s display. f (Tune): Turn to select files. © SEEK: Press to go to the start of the track, if more than ten seconds have played. Press and hold or press multiple times to continue moving backward through tracks. ¨ SEEK: Press to go to the next track.
Infotainment System 4. Turn f to scroll through the files in the selected folder. h (Music Navigator): Press the softkey below h to view and 5. Press f to select the file to be played. select a file on an iPod, using the iPod's menu system. Files are sorted by: To skip through large lists, the five softkeys can be used to navigate in the following order: . Playlists . Artists . First softkey, first item in the list. . Albums .
7-34 Infotainment System ' (Repeat Track): Press the softkey below ' to repeat one Auxiliary Devices To use Shuffle: The vehicle may have a 3.5 mm (1/8 in) auxiliary input jack located on the lower right side of the faceplate and for vehicles with a USB port, it is located in the center console. Press the softkey below >, 2, < or = to select between Using the 3.5 mm (1/8 in) Auxiliary Input Jack track. The tab appears raised when Repeat Track is being used.
Infotainment System DVD/CD AUX (Auxiliary): Press to select between DVD, CD, or Auxiliary. . . . . If an auxiliary input device is not connected, “No Aux Input Device” displays. When a disc is in either slot, the DVD/CD text tab and a message showing the track or chapter number displays. If an auxiliary input device is not connected, and a disc is in both the DVD slot and the CD slot the DVD/CD AUX button only cycles between the two sources and does not indicate “No Aux Input Device”.
7-36 Infotainment System Rear Seat Infotainment Rear Seat Entertainment (RSE) System The vehicle may have a DVD Rear Seat Entertainment (RSE) system. The RSE system works with the vehicle's audio system. The DVD player is part of the front radio. The RSE system includes a radio with a DVD player, a video display screen, audio/video jacks, two wireless headphones, and a remote control. See Operation on page 7‑2 for more information on the vehicle's audio/DVD system.
Infotainment System 7-37 The headphones may automatically turn off after four hours of continuous use. on the upper right side, above the ear pad and should be positioned on the right ear. Battery Replacement To adjust the volume on the headphones, use the volume control located on the right side. Notice: Do not store the headphones in heat or direct sunlight. This could damage the headphones and repairs will not be covered by the warranty. Storage in extreme cold can weaken the batteries.
7-38 Infotainment System Audio/Video (A/V) Jacks The A/V jacks are color coded to match typical home entertainment system equipment. The yellow jack (A) is for the video input. The white jack (B) is for the left audio input. The red jack (C) is for the right audio input. Power for auxiliary devices is not supplied by the radio system.
Infotainment System The RSE system always transmits the audio signal to the wireless headphones, if there is audio available. See “Headphones” earlier in this section for more information. The DVD player is capable of outputting audio to the wired headphone jacks on the RSA system, if the vehicle has this feature. The DVD player can be selected as an audio source on the RSA system. See Rear Seat Audio (RSA) System on page 7‑44 for more information.
7-40 Infotainment System If a CD or DVD is in the Radio DVD slot, the remote control O button can be used to turn on the video screen display and start the disc. The radio can also turn on the video screen display. See Operation on page 7‑2 for more information. Notice: Storing the remote control in a hot area or in direct sunlight can damage it, and the repairs will not be covered by the warranty. Storage in extreme cold can weaken the batteries. Keep the remote control stored in a cool, dry place.
Infotainment System u (Next Track/Chapter): Press to go to the beginning of the next chapter or track. This button might not work when the DVD is playing the copyright information or the previews. r (Fast Reverse): Press to quickly reverse the DVD or CD. To stop fast reversing a DVD video, press s. To stop fast reversing a DVD audio or CD, release r. This button might not work when the DVD is playing the copyright information or the previews. [ (Fast Forward): Press to fast forward the DVD or CD.
7-42 Infotainment System Battery Replacement To change the remote control batteries: 1. Slide the rear cover back, on the remote control. 2. Replace the two batteries in the compartment. Make sure that they are installed correctly, using the diagram on the inside of the battery compartment. 3. Replace the battery cover. If the remote control is to be stored for a long period of time, remove the batteries and keep them in a cool, dry place.
Infotainment System 7-43 Tips and Troubleshooting Chart (cont'd) DVD Display Error Messages Problem Recommended Action After stopping the player, I push Play but sometimes the DVD starts where I left off and sometimes at the beginning. If the stop button was pressed one time, the DVD player resumes playing where the DVD was stopped. If the stop button was pressed two times the DVD player begins to play from the beginning of the DVD.
7-44 Infotainment System DVD Distortion Video distortion can occur when operating cellular phones, scanners, CB radios, Global Position Systems (GPS)*, two-way radios, mobile fax, or walkie talkies. It might be necessary to turn off the DVD player when operating one of these devices in or near the vehicle. *Excludes the OnStar® System. Cleaning the RSE Overhead Console When cleaning the RSE overhead console surface, use only a clean cloth dampened with clean water.
Infotainment System 7-45 While listening to a disc, press ¨ to go to the next track or chapter on the disc. Press © to go back to the start of the current track or chapter (if more than ten seconds have played). This function is inactive, with some radios, if the front seat passengers are listening to the disc. P (Power): Press to turn the RSA on or off. Volume: Turn to increase or to decrease the volume of the wired headphones.
7-46 Infotainment System When a CD or DVD audio disc is playing, press PROG to go to the beginning of the CD or DVD audio. This function is inactive, with some radios, if the front seat passengers are listening to the disc. When a disc is playing in the CD or DVD changer, press PROG to select the next disc, if multiple discs are loaded. This function is inactive, with some radios, if the front seat passengers are listening to the disc.
Infotainment System Bluetooth Controls Pairing Information: Use the buttons located on the steering wheel to operate the in‐vehicle Bluetooth system. See Steering Wheel Controls on page 5‑3 for more information. . Up to five cell phones can be paired to the in‐vehicle Bluetooth system. . The pairing process is disabled when the vehicle is moving. . The in‐vehicle Bluetooth system automatically links with the first available paired cell phone in the order the phone was paired.
7-48 Infotainment System 5. The system prompts for a name for the phone. Use a name that best describes the phone. This name will be used to indicate which phone is connected. The system then confirms the name provided. 6. The system responds with “ has been successfully paired” after the pairing process is complete. 7. Repeat Steps 1 through 7 for additional phones to be paired. Listing All Paired and Connected Phones 1. Press and hold b g for two seconds.
Infotainment System Storing Name Tags The system can store up to thirty phone numbers as name tags that are shared between the Bluetooth and OnStar systems. The system uses the following commands to store and retrieve phone numbers: . Store . Digit Store . Directory Using the Store Command The store command allows a phone number to be stored without entering the digits individually. 1. Press and hold b g for two seconds. The system responds with “Ready” followed by a tone. 2. Say “Store”.
7-50 Infotainment System Using the Digit Store Command The digit store command allows a phone number to be stored by entering the digits individually. 1. Press and hold b g for two seconds. The system responds with “Ready” followed by a tone. 2. Say “Digit Store”. The system responds with “Please say the first digit to store” followed by a tone. 3. Say the first digit to be stored. The system will repeat back the digit it heard followed by a tone.
Infotainment System To use the delete command: 1. Press and hold b g for two seconds. The system responds with “Ready” followed by a tone. 2. Say “Delete”. The system responds with “Delete, please say the name tag” followed by a tone. 3. Say the name tag to be deleted. The system responds with “Would you like to delete, ? Please say yes or no”. . . If the name tag is correct, say “Yes” to delete the name tag. The system responds with “OK, deleting , returning to the main menu.
7-52 Infotainment System 3. Say the entire number without pausing. . If the system recognizes the number, it responds with “OK, Dialing” and dials the number. . If the system does not recognize the number, it confirms the numbers followed by a tone. If the number is correct, say “Yes”. The system responds with “OK, Dialing” and dials the number. If the number is not correct, say “No”. The system will ask for the number to be re‐entered. Using the Digit Dial Command 1.
Infotainment System 3. Say the name tag of the person to call. . . If the system clearly recognizes the name tag it responds with “OK, calling, ” and dials the number. If the system is unsure it recognizes the right name tag, it confirms the name tag followed by a tone. If the name tag is correct, say “Yes”. The system responds with “OK, calling, ” and dials the number. If the name tag is not correct, say “No”. The system will ask for the name tag to be re‐entered.
7-54 Infotainment System Three‐Way Calling Muting a Call Three‐Way Calling must be supported on the Bluetooth phone and enabled by the wireless service carrier to work. During a call, all sounds from inside the vehicle can be muted so that the person on the other end of the call cannot hear them. 1. While on a call press b g. The system responds with “Ready” followed by a tone. To Mute a call 2. Say “Three‐way call”. The system responds with “Three‐way call, please say dial or call”. 3.
Infotainment System Voice Pass-Thru Voice Pass‐Thru allows access to the voice recognition commands on the cell phone. See the cell phone manufacturers user guide to see if the cell phone supports this feature. This feature can be used to verbally access contacts stored in the cell phone. 1. Press and hold b g for two seconds. The system responds with “Ready” followed by a tone. 2. Say “Bluetooth”. The system responds with “Bluetooth ready” followed by a tone. 3. Say “Voice”.
7-56 Infotainment System Sending a Stored Name Tag During a Call 1. Press b g. The system responds with “Ready” followed by a tone. 2. Say “Send name tag.” The system responds with “Say a name tag to send tones” followed by a tone. 3. Say the name tag to send. . If the system clearly recognizes the name tag it responds with “OK, Sending ” and the dial tones are sent and the call continues. .
Climate Controls Climate Controls 8-1 Climate Control Systems Dual Automatic Climate Control System Climate Control Systems Dual Automatic Climate Control System . . . . . . . . . . . . . . . . . . . . . . 8-1 Rear Climate Control System (Rear Climate Control Only) . . . . . . . . . . . . . . . . 8-7 Rear Climate Control System (Rear Climate with Rear Seat Audio) . . . . . . . . . . . . . . . . . . . . . . . 8-8 The heating, cooling, and ventilation in the vehicle can be controlled with this system.
8-2 Climate Controls Display Function Automatic Operation Each time the temperature, mode, or fan control buttons are pressed, the climate control display shows that function along with the inside temperature setting. The outside temperature is displayed on the instrument panel cluster. AUTO (Automatic): The system automatically controls the inside temperature, the air delivery, and the fan speed. O (On/Off): Press to turn the climate control system on or off.
Climate Controls Temperature Control The driver and passenger side temperature buttons are used to adjust the temperature of the air coming through the system. The temperature can be adjusted even if the system is turned off since outside air still enters the vehicle, unless the recirculation mode is selected. See “Recirculation” later in this section. Driver Side Temperature Control: Press the + or − buttons to increase or decrease the driver side temperature.
8-4 Climate Controls 6 (Floor): Air is directed to the floor outlets, with some of the air directed to the windshield, side window, and second row floor outlets. In this mode, the system uses outside air. the vehicle. The air conditioning system runs automatically in this setting, unless the outside temperature is less than 4°C (40°F). - (Defog): This mode clears the windows of fog or moisture. Air is directed to the windshield, floor outlets, and side window vents.
Climate Controls @ (Recirculation): Press to turn the recirculation mode on or off. An indicator light comes on when recirculation is on. When the engine is turned off, the recirculation mode automatically turns off and must be re‐selected when the engine is turned on again. REAR: Press to turn the rear heating and air conditioning on or off. See Rear Climate Control System (Rear Climate Control Only) on page 8‑7 or Rear Climate Control System (Rear Climate with Rear Seat Audio) on page 8‑8.
8-6 Climate Controls Sensors The solar sensor, located in the defrost grille in the middle of the instrument panel, monitors the solar heat. Do not cover the solar sensor or the system will not work properly. There is also an exterior temperature sensor located behind the front grille. This sensor reads the outside air temperature and helps maintain the temperature inside the vehicle. Any cover on the front of the vehicle could cause a false reading in the displayed temperature.
Climate Controls Rear Climate Control System (Rear Climate Control Only) 8-7 Independent Mode: This mode directs rear seating airflow according to the settings of the rear controls. It comes on when any rear control is adjusted. Fan Control: Turn clockwise or counterclockwise to increase or decrease the fan speed. Turn the knob to 9 to turn the fan off. Temperature Control: Turn clockwise or counterclockwise to increase or decrease the airflow temperature. A. Fan Control B. Temperature Control C.
8-8 Climate Controls Rear Climate Control System (Rear Climate with Rear Seat Audio) Mimic Mode: This mode matches the rear climate control to the front climate control settings. It comes on when REAR is pressed. Independent Mode: This mode directs rear seating airflow according to the settings of the rear controls. It comes on when any rear control is adjusted. D C (Fan Control): Press the fan up or down buttons to increase or decrease the fan speed. A. Fan Control B. Air Delivery Mode Control C.
Climate Controls H (Vent): Air is directed through the overhead outlets. ) (Bi-Level): Air is directed through the rear floor outlets, as well as the overhead outlets. 6 (Floor): Air is directed through the floor outlets. The rear system floor outlets are located under the third row seats. Air Vents Use the slider switch in the center of the outlet, to change the direction of the air flow. Use the thumbwheel near the outlet to control the amount of air flow or to shut off the airflow.
8-10 Climate Controls 2 NOTES
Driving and Operating Driving and Operating Shifting Into Park . . . . . . . . . . . . 9-21 Shifting Out of Park . . . . . . . . . . 9-22 Parking Over Things That Burn . . . . . . . . . . . . . . . . . . 9-23 Engine Exhaust Driving Information Defensive Driving . . . . . . . . . . . . . 9-2 Drunk Driving . . . . . . . . . . . . . . . . . 9-2 Control of a Vehicle . . . . . . . . . . . 9-3 Braking . . . . . . . . . . . . . . . . . . . . . . . 9-3 Steering . . . . . . . . . . . . . . . . . . . . . . .
9-2 Driving and Operating Driving Information Defensive Driving Defensive driving means “always expect the unexpected.” The first step in driving defensively is to wear your safety belt, see Safety Belts on page 3‑13. { WARNING Assume that other road users (pedestrians, bicyclists, and other drivers) are going to be careless and make mistakes. Anticipate what they might do and be ready. In addition: . Allow enough following distance between you and the driver in front of you. .
Driving and Operating For persons under 21, it is against the law in every U.S. state to drink alcohol. There are good medical, psychological, and developmental reasons for these laws. The obvious way to eliminate the leading highway safety problem is for people never to drink alcohol and then drive. Medical research shows that alcohol in a person's system can make crash injuries worse, especially injuries to the brain, spinal cord, or heart.
9-4 Driving and Operating But even in three‐fourths of a second, a vehicle moving at 100 km/h (60 mph) travels 20 m (66 ft). That could be a lot of distance in an emergency, so keeping enough space between the vehicle and others is important.
Driving and Operating If there is a need to reduce speed, do it before entering the curve, while the front wheels are straight. Try to adjust the speed so you can drive through the curve. Maintain a reasonable, steady speed. Wait to accelerate until out of the curve, and then accelerate gently into the straightaway. page 9‑3. It is better to remove as much speed as possible from a collision. Then steer around the problem, to the left or right depending on the space available.
9-6 Driving and Operating if there is nothing in the way, steer so that the vehicle straddles the edge of the pavement. Turn the steering wheel 8 to 13 cm (3 to 5 inches), about one-eighth turn, until the right front tire contacts the pavement edge. Then turn the steering wheel to go straight down the roadway.
Driving and Operating Driving on Wet Roads Rain and wet roads can reduce vehicle traction and affect your ability to stop and accelerate. Always drive slower in these types of driving conditions and avoid driving through large puddles and deep‐standing or flowing water. { WARNING Wet brakes can cause crashes. They might not work as well in a quick stop and could cause pulling to one side. You could lose control of the vehicle.
9-8 Driving and Operating Highway Hypnosis Hill and Mountain Roads Always be alert and pay attention to your surroundings while driving. If you become tired or sleepy, find a safe place to park your vehicle and rest. Driving on steep hills or through mountains is different than driving on flat or rolling terrain. Tips for driving in these conditions include: . Keep the vehicle serviced and in good shape. . Check all fluid levels and brakes, tires, cooling system, and transmission. .
Driving and Operating WARNING (Continued) Winter Driving Driving on Snow or Ice You would then have poor braking or even none going down a hill. You could crash. Always have the engine running and the vehicle in gear when going downhill. . Stay in your own lane. Do not swing wide or cut across the center of the road. Drive at speeds that let you stay in your own lane. . Top of hills: Be alert — something could be in your lane (stalled car, accident). .
9-10 Driving and Operating Blizzard Conditions Being stuck in snow can be in a serious situation. Stay with the vehicle unless there is help nearby. If possible, use the Roadside Assistance Program on page 13‑6. To get help and keep everyone in the vehicle safe: . Turn on the hazard warning flashers. . Tie a red cloth to an outside mirror. { WARNING Snow can trap engine exhaust under the vehicle. This may cause exhaust gases to get inside.
Driving and Operating WARNING (Continued) Snow can trap exhaust gases under your vehicle. This can cause deadly CO (carbon monoxide) gas to get inside. CO could overcome you and kill you. You cannot see it or smell it, so you might not know it is in your vehicle. Clear away snow from around the base of your vehicle, especially any that is blocking the exhaust. Run the engine for short periods only as needed to keep warm, but be careful.
9-12 Driving and Operating Rocking the Vehicle to Get it Out Turn the steering wheel left and right to clear the area around the front wheels. Turn off any traction or stability system. Shift back and forth between R (Reverse) and a forward gear, spinning the wheels as little as possible. To prevent transmission wear, wait until the wheels stop spinning before shifting gears. Release the accelerator pedal while shifting, and press lightly on the accelerator pedal when the transmission is in gear.
Driving and Operating Tire and Loading Information Label maximum vehicle capacity weight (B) in kilograms and pounds. The Tire and Loading Information label also shows the size of the original equipment tires (C) and the recommended cold tire inflation pressures (D). For more information on tires and inflation see Tires on page 10‑37 and Tire Pressure on page 10‑44 . Example Label A vehicle specific Tire and Loading Information label is attached to the center pillar (B-pillar) of your vehicle.
9-14 Driving and Operating 4. The resulting figure equals the available amount of cargo and luggage load capacity. For example, if the “XXX” amount equals 1400 lbs and there will be five 150 lb passengers in your vehicle, the amount of available cargo and luggage load capacity is 650 lbs (1400 − 750 (5 x 150) = 650 lbs). 5. Determine the combined weight of luggage and cargo being loaded on the vehicle. That weight may not safely exceed the available cargo and luggage load capacity calculated in Step 4.
Driving and Operating 9-15 seating positions. The combined weight of the driver, passengers, and cargo should never exceed your vehicle's capacity weight. Certification/Tire Label Example 2 A. Vehicle Capacity Weight for Example 2 = 453 kg (1,000 lbs). B. Subtract Occupant Weight @ 68 kg (150 lbs) × 5 = 340 kg (750 lbs). C. Available Cargo Weight = 113 kg (250 lbs). Example 3 A. Vehicle Capacity Weight for Example 3 = 453 kg (1,000 lbs). B.
9-16 Driving and Operating The GVWR includes the weight of the vehicle, all occupants, fuel, and cargo. The Certification/Tire label also tells you the maximum weights for the front and rear axles, called the Gross Axle Weight Rating (GAWR). To find out the actual loads on your front and rear axles, you need to go to a weigh station and weigh your vehicle. Your dealer/retailer can help you with this. Be sure to spread out your load equally on both sides of the centerline.
Driving and Operating WARNING (Continued) . Do not leave an unsecured child restraint in your vehicle. . When you carry something inside the vehicle, secure it whenever you can. . Do not leave a seat folded down unless you need to. Starting and Operating . Avoid making hard stops for the first 322 km (200 miles) or so. During this time the new brake linings are not yet broken in. Hard stops with new linings can mean premature wear and earlier replacement.
9-18 Driving and Operating Ignition Positions and turn it only with your hand. If the key cannot be turned by hand, see your dealer/retailer. the ignition and steering wheel. Use this position if the vehicle must be pushed or towed. ( (LOCK/OFF): R (ON/RUN): This position can be used to operate the electrical accessories and to display some instrument panel warning and indicator lights. The switch stays in this position when the engine is running. The transmission is also unlocked in this position.
Driving and Operating Retained Accessory Power (RAP) These vehicle accessories can be used for up to 10 minutes after the ignition key is turned off: . Audio System . Power Windows . Sunroof (if equipped) Power to the windows and sunroof will work up to 10 minutes or until a door is opened. The radio continues to work for 10 minutes or until the driver's door is opened. For an additional 10 minutes of operation, close all the doors and turn the key to ON/RUN and then back to LOCK/OFF.
9-20 Driving and Operating 2. If the engine does not start after 5‐10 seconds, especially in very cold weather (below 0°F or −18°C), it could be flooded with too much gasoline. Try pushing the accelerator pedal all the way to the floor and holding it there as you hold the key in START for up to a maximum of 15 seconds. Wait at least 15 seconds between each try, to allow the cranking motor to cool down. When the engine starts, let go of the key and accelerator.
Driving and Operating { WARNING Plugging the cord into an ungrounded outlet could cause an electrical shock. Also, the wrong kind of extension cord could overheat and cause a fire. You could be seriously injured. Plug the cord into a properly grounded three-prong 110-volt AC outlet. If the cord will not reach, use a heavy-duty three-prong extension cord rated for at least 15 amps. 4. Before starting the engine, be sure to unplug and store the cord as it was before to keep it away from moving engine parts.
9-22 Driving and Operating you leave it. After you have moved the shift lever into P (Park), hold the regular brake pedal down. Then, see if you can move the shift lever away from P (Park) without first pushing the button. Shifting Out of Park To shift out of P (Park): The vehicle is equipped with an electronic shift lock release system. The shift lock release is designed to: 1. Apply the brake pedal. If you can, it means that the shift lever was not fully locked in P (Park). .
Driving and Operating Parking Over Things That Burn { WARNING Things that can burn could touch hot exhaust parts under the vehicle and ignite. Do not park over papers, leaves, dry grass, or other things that can burn. Engine Exhaust { WARNING Engine exhaust contains Carbon Monoxide (CO) which cannot be seen or smelled. Exposure to CO can cause unconsciousness and even death. WARNING (Continued) . The vehicle’s exhaust system has been modified, damaged or improperly repaired. .
9-24 Driving and Operating Running the Vehicle While Parked It is better not to park with the engine running. But if you ever have to, here are some things to know. { WARNING Idling a vehicle in an enclosed area with poor ventilation is dangerous. Engine exhaust may enter the vehicle. Engine exhaust contains Carbon Monoxide (CO) which cannot be seen or smelled. It can cause unconsciousness and even death. Never run the engine in an enclosed area that has no fresh air ventilation.
Driving and Operating { WARNING It is dangerous to get out of the vehicle if the shift lever is not fully in P (Park) with the parking brake firmly set. The vehicle can roll. Do not leave the vehicle when the engine is running unless you have to. If you have left the engine running, the vehicle can move suddenly. You or others could be injured. To be sure the vehicle will not move, even when you are on fairly level ground, always set the parking brake and move the shift lever to P (Park).
9-26 Driving and Operating D (Drive): This position is for normal driving. It provides the best fuel economy. If you need more power for passing, and you are: designed to improve fuel economy and performance. Use the brake to hold the vehicle on a hill. Do not use the accelerator pedal. . Going less than 56 km/h (35 mph), push the accelerator pedal about halfway down. . Going about 56 km/h (35 mph) or more, push the accelerator all the way down.
Driving and Operating While in L (Low), the transmission will prevent shifting to a lower gear range if the engine speed is too high. You have a brief period of time to slow the vehicle. If vehicle speed is not reduced within the time allowed, the lower gear range shift will not be completed. You must further slow the vehicle, then press the − (Minus) button to the desired lower gear range. Automatic Engine Grade braking is not available when the ERS is active.
9-28 Driving and Operating Drive Systems Brakes All-Wheel Drive Antilock Brake System (ABS) With this feature, engine power is always sent to all four wheels. It is fully automatic, and adjusts itself as needed for road conditions. When using a compact spare tire on an AWD vehicle, the system automatically detects the compact spare and disables AWD. To restore AWD operation and prevent excessive wear on system, replace the compact spare with a full-size tire as soon as possible.
Driving and Operating Remember: ABS does not change the time needed to get a foot up to the brake pedal or always decrease stopping distance. If you get too close to the vehicle in front of you, there will not be enough time to apply the brakes if that vehicle suddenly slows or stops. Always leave enough room up ahead to stop, even with ABS. Parking Brake Using ABS Do not pump the brakes. Just hold the brake pedal down firmly and let ABS work.
9-30 Driving and Operating Brake Assist This vehicle has a brake assist feature designed to assist the driver in stopping or decreasing vehicle speed in emergency driving conditions. This feature uses the stability system hydraulic brake control module to supplement the power brake system under conditions where the driver has quickly and forcefully applied the brake pedal in an attempt to quickly stop or slow down the vehicle.
Driving and Operating The traction control disable button is located on the instrument panel below the climate controls. The traction control part of StabiliTrak can be turned off by pressing and releasing the traction control disable button. Traction control can be turned on by pressing and releasing the traction control disable button if not automatically shut off for any other reason.
9-32 Driving and Operating The engine speed management will be disabled. In this mode, engine power is not reduced automatically and the driven wheels can spin more freely. This can cause the brake-traction control to activate constantly. Notice: If the wheel(s) of one axle is allowed to spin excessively while the StabiliTrak, ABS and brake warning lights and any relevant DIC messages are displayed, the transfer case could be damaged. The repairs would not be covered by the vehicle warranty.
Driving and Operating [ (Cancel): Press to cancel cruise control without erasing the set speed from memory. 1. Press the I button to turn the cruise control system on. Setting Cruise Control 3. Press and release the SET– button located on the steering wheel. Cruise control will not work if the parking brake is set, or if the master cylinder brake fluid level is low. The cruise control buttons are located on left side of the steering wheel. T (On/Off): Press to turn cruise control on and off.
9-34 Driving and Operating Increasing Speed While Using Cruise Control If the cruise control is already engaged, . . Press and hold the +RES button on the steering wheel until the desired speed is reached, then release it. To increase vehicle speed in small increments, press the +RES button briefly. Each time this is done, the vehicle goes about 1.6 km/h (1 mph) faster. Reducing Speed While Using Cruise Control If the cruise control system is already engaged, .
Driving and Operating Object Detection Systems Ultrasonic Parking Assist For vehicles with the Ultrasonic Rear Parking Assist (URPA) system, it operates at speeds less than 8 km/h (5 mph), and assists the driver with parking and avoiding objects while in R (Reverse). The sensors on the rear bumper are used to detect the distance to an object up to 2.5 m (8 ft) behind the vehicle, and at least 25.4 cm (10 in) off the ground.
9-36 Driving and Operating When the System Does Not Seem to Work Properly If the URPA system does not activate due to a temporary condition, the message PARK ASSIST OFF displays on the DIC when the shift lever is moved into R (Reverse). This may occur under the following conditions: . The driver disables the system. . The ultrasonic sensors are not clean. Keep the vehicle's rear bumper free of mud, dirt, snow, ice and slush. For cleaning instructions, see Exterior Care on page 10‑87. .
Driving and Operating WARNING (Continued) Your judged distances using the screen will differ from actual distances. So if you do not use proper care before backing up, you could hit a vehicle, child, pedestrian, bicyclist, or pet, resulting in vehicle damage, injury, or death. Even though the vehicle has the RVC system, always check carefully before backing up by checking behind and around the vehicle.
9-38 Driving and Operating There is a message on the rear vision camera screen that states “Check Surroundings for Safety”. Turning the Rear Vision Camera System On or Off To turn the rear vision camera system on or off: Adjusting the Brightness and Contrast of the Screen 1. Shift into P (Park). To adjust the brightness and contrast of the screen, press the MENU button while the rear vision camera image is on the display. Any adjustments made will only affect the rear vision camera screen. 2.
Driving and Operating Symbols The navigation system may have a feature that lets the driver view symbols on the navigation screen while using the rear vision camera. The Ultrasonic Rear Park Assist (URPA) system must not be disabled to use the caution symbols. If URPA has been disabled and the symbols have been turned on, the Rear Parking Assist Symbols Unavailable error message may display. See Ultrasonic Parking Assist on page 9‑35. The symbols appear when an object has been detected by the URPA system.
9-40 Driving and Operating Rear Vision Camera Location The area displayed by the camera is limited and does not display objects that are close to either corner or under the bumper. The area displayed can vary depending on vehicle orientation or road conditions. The distance of the image that appears on the screen differs from the actual distance. The following illustration shows the field of view that the camera provides. The camera is located above the license plate. A. View displayed by the camera.
Driving and Operating When the System Does Not Seem To Work Properly . The rear vision camera system might not work properly or display a clear image if: . The RVC is turned off. See “Turning the Rear Camera System On or Off” earlier in this section. . It is dark. . The sun or the beam of headlights is shining directly into the camera lens. . Ice, snow, mud, or anything else builds up on the camera lens. Clean the lens, rinse it with water, and wipe it with a soft cloth. .
9-42 Driving and Operating Fuel Recommended Fuel Use of the recommended fuel is an important part of the proper maintenance of this vehicle. To help keep the engine clean and maintain optimum vehicle performance, we recommend the use of gasoline advertised as TOP TIER Detergent Gasoline. Use regular unleaded gasoline with a posted octane rating of 87 or higher. If the octane rating is less than 87, an audible knocking noise, commonly referred to as spark knock, might be heard when driving.
Driving and Operating California Fuel Requirements Fuels in Foreign Countries If the vehicle is certified to meet California Emissions Standards, it is designed to operate on fuels that meet California specifications. See the underhood emission control label. If this fuel is not available in states adopting California emissions standards, the vehicle will operate satisfactorily on fuels meeting federal specifications, but emission control system performance might be affected.
9-44 Driving and Operating label on the fuel pump to ensure gasoline meets enhanced detergency standards developed by the auto companies. A list of marketers providing TOP TIER Detergent Gasoline can be found at www.toptiergas.com. For customers who do not use TOP TIER Detergent Gasoline regularly, one bottle of GM Fuel System Treatment PLUS, added to the fuel tank at every engine oil change, can help clean deposits from fuel injectors and intake valves.
Driving and Operating Filling the Tank { WARNING Fuel vapor burns violently and a fuel fire can cause bad injuries. To help avoid injuries to you and others, read and follow all the instructions on the fuel pump island. Turn off the engine when refueling. Do not smoke near fuel or when refueling the vehicle. Do not use cellular phones. Keep sparks, flames, and smoking materials away from fuel. Do not leave the fuel pump unattended when refueling the vehicle. This is against the law in some places.
9-46 Driving and Operating When replacing the fuel cap, turn it clockwise until it clicks. Make sure the cap is fully installed. The diagnostic system can determine if the fuel cap has been left off or improperly installed. This would allow fuel to evaporate into the atmosphere. See Malfunction Indicator Lamp on page 5‑19. { WARNING If a fire starts while you are refueling, do not remove the nozzle. Shut off the flow of fuel by shutting off the pump or by notifying the station attendant.
Driving and Operating Towing General Towing Information Only use towing equipment that has been designed for the vehicle. Contact your dealer/retailer or trailering retailer for assistance with preparing the vehicle for towing a trailer. See the following trailer towing information in this section: . For information on driving while towing a trailer, see “Driving Characteristics and Towing Tips”. . For maximum vehicle and trailer weights, see “Trailer Towing”. .
9-48 Driving and Operating Pulling A Trailer . The vehicle can tow in D (Drive). Use a lower gear if the transmission shifts too often. See “Tow/Haul Mode” later in this section. . Obey speed limit restrictions when towing a trailer. . The vehicle is designed primarily as a passenger and load carrying vehicle. If a trailer is towed, the vehicle will require more frequent maintenance due to the additional load. Here are some important points: .
Driving and Operating Tow/Haul Mode Tow/Haul assists when pulling a heavy trailer or a large or heavy load. The purpose of the Tow/Haul mode is to: . Reduce the frequency and improve the predictability of transmission shifts. Press this button located on the console to turn on and turn off the Tow/Haul mode. . Provide the same solid shift feel as when the vehicle is unloaded. The Tow/Haul light on the instrument panel comes on to indicate that Tow/Haul mode has been selected. . .
9-50 Driving and Operating Following Distance Making Turns Stay at least twice as far behind the vehicle ahead as you would when driving the vehicle without a trailer. This can help to avoid situations that require heavy braking and sudden turns. Notice: Making very sharp turns while trailering could cause the trailer to come in contact with the vehicle. The vehicle could be damaged. Avoid making very sharp turns while trailering.
Driving and Operating When towing at high altitude on steep uphill grades, engine coolant will boil at a lower temperature than at normal altitudes. If the engine is turned off immediately after towing at high altitude on steep uphill grades, the vehicle may show signs similar to engine overheating. To avoid this, let the engine run while parked, preferably on level ground, with the transmission in P (Park) for a few minutes before turning the engine off.
9-52 Driving and Operating Leaving After Parking on a Hill 1. Apply and hold the brake pedal while you: . Start the engine. . Shift into a gear. . Release the parking brake. Check periodically to see that all hitch nuts and bolts are tight. Weight of the Trailer Engine Cooling When Trailer Towing Speed, altitude, road grades, outside temperature, special equipment, and the amount of tongue weight the vehicle can carry must be considered.
Driving and Operating 9-53 Use the following chart to determine how much the vehicle can weigh, based upon the vehicle model and options.
9-54 Driving and Operating GVWR (Gross Vehicle Weight Rating) or the RGAWR (Rear Gross Axle Weight Rating). The effect of additional weight may reduce the trailering capacity more than the total of the additional weight. Consider the following example: If a weight-carrying hitch or a weight-distributing hitch is being used, the trailer tongue (A) should weigh 10‐15 percent of the total loaded trailer weight (B).
Driving and Operating added to the front axle weight and 181 kg (400 lbs) to the rear axle weight. The vehicle now weighs: Weight is still below 3 266 kg (7,200 lbs) and you might think 318 additional kilograms (700 lbs) should be subtracted from the trailering capacity to stay within GCWR limits. The maximum trailer would only be 3 538 kg (7,800 lbs). You may go further and think the tongue weight should be limited to less than 454 kg (1,000 lbs) to avoid exceeding GVWR.
9-56 Driving and Operating Towing Equipment Hitches Weight-Distributing Hitches and Weight Carrying Hitches It is important to have the correct hitch equipment. Crosswinds, large trucks going by and rough roads are a few reasons why the right hitch is needed. . . The rear bumper on the vehicle is not intended for hitches. Do not attach rental hitches or other bumper-type hitches to it. Use only a frame-mounted hitch that does not attach to the bumper.
Driving and Operating Trailer Wiring Harness Basic Trailer Wiring The trailer wiring harness, with a seven-pin connector, is located at the rear of the vehicle and is tied to the vehicle's frame. The harness connector can be plugged into a seven-pin universal heavy-duty trailer connector available through your dealer/retailer. The seven-wire harness contains the following trailer circuits: . .
9-58 Driving and Operating Conversions and Add-Ons Add-On Electrical Equipment Notice: Do not add anything electrical to the vehicle unless you check with your dealer/ retailer first. Some electrical equipment can damage the vehicle and the damage would not be covered by the vehicle's warranty. Some add-on electrical equipment can keep other components from working as they should. Add-on equipment can drain the vehicle battery, even if the vehicle is not operating. The vehicle has an airbag system.
Vehicle Care Vehicle Care General Information General Information . . . . . . . . . . California Proposition 65 Warning . . . . . . . . . . . . . . . . . California Perchlorate Materials Requirements . . . . Accessories and Modifications . . . . . . . . . . . . . . . 10-2 10-3 10-3 10-3 Vehicle Checks Doing Your Own Service Work . . . . . . . . . . . . . . . 10-4 Hood . . . . . . . . . . . . . . . . . . . . . . . . 10-5 Engine Compartment Overview . . . . . . . . . . . . . . . . . . . 10-6 Engine Cover .
10-2 Vehicle Care Tire Inspection . . . . . . . . . . . . . . 10-50 Tire Rotation . . . . . . . . . . . . . . . 10-50 When It Is Time for New Tires . . . . . . . . . . . . . . . . . . . . . . 10-51 Buying New Tires . . . . . . . . . . . 10-52 Different Size Tires and Wheels . . . . . . . . . . . . . . . . . . . 10-54 Uniform Tire Quality Grading . . . . . . . . . . . . . . . . . . . 10-54 Wheel Alignment and Tire Balance . . . . . . . . . . . . . . . . . . . 10-56 Wheel Replacement . . . . . . . .
Vehicle Care 10-3 California Proposition 65 Warning California Perchlorate Materials Requirements Accessories and Modifications Most motor vehicles, including this one, contain and/or emit chemicals known to the State of California to cause cancer and birth defects or other reproductive harm. Engine exhaust, many parts and systems, many fluids, and some component wear by-products contain and/or emit these chemicals.
10-4 Vehicle Care Damage to vehicle components resulting from the installation or use of non‐GM certified parts, including control module modifications, is not covered under the terms of the vehicle warranty and may affect remaining warranty coverage for affected parts. GM Accessories are designed to complement and function with other systems on the vehicle. Your GM dealer/retailer can accessorize the vehicle using genuine GM Accessories.
Vehicle Care Hood Before closing the hood, be sure all filler caps are on properly. To open the hood: 1. Pull the hood release handle with this symbol on it. It is located under the instrument panel on the driver side of the vehicle. 10-5 Pull the hood down to close. Lower the hood until the lifting pressure of the strut is reduced. Then allow the hood to fall and latch into place under its own weight. Check to make sure the hood is closed.
10-6 Vehicle Care Engine Compartment Overview
Vehicle Care A. Radiator Pressure Cap. See Cooling System on page 10‑13. B. Engine Coolant Recovery Cap. See Cooling System on page 10‑13. C. Remote Negative (−) Terminal. See Jump Starting on page 10‑80. D. Engine Compartment Fuse Block on page 10‑31. E. Remote Positive (+) Terminal. See Jump Starting on page 10‑80. F. Power Steering Reservoir and Cap (under engine cover). See Power Steering Fluid on page 10‑19. G. Engine Oil Fill Cap. See “When to Add Engine Oil” under Engine Oil on page 10‑8. H.
10-8 Vehicle Care Engine Oil When to Add Engine Oil Checking Engine Oil It is a good idea to check the engine oil level at each fuel fill. In order to get an accurate reading, the oil must be warm and the vehicle must be on level ground. The engine oil dipstick handle is a yellow loop. See Engine Compartment Overview on page 10‑6 for the location of the engine oil dipstick. 1. Turn off the engine and give the oil several minutes to drain back into the oil pan.
Vehicle Care What Kind of Engine Oil to Use Look for three things: . GM6094M Use only an oil that meets GM Standard GM6094M. . SAE 5W-30 SAE 5W-30 is best for the vehicle. These numbers on an oil container show its viscosity, or thickness. Do not use other viscosity oils such as SAE 20W-50. . American Petroleum Institute (API) starburst symbol Oils meeting these requirements should have the starburst symbol on the container.
10-10 Vehicle Care Engine Oil Life System When to Change Engine Oil This vehicle has a computer system that indicates when to change the engine oil and filter. This is based on engine revolutions and engine temperature, and not on mileage. Based on driving conditions, the mileage at which an oil change is indicated can vary considerably. For the oil life system to work properly, the system must be reset every time the oil is changed.
Vehicle Care What to Do with Used Oil Used engine oil contains certain elements that can be unhealthy for your skin and could even cause cancer. Do not let used oil stay on your skin for very long. Clean your skin and nails with soap and water, or a good hand cleaner. Wash or properly dispose of clothing or rags containing used engine oil. See the manufacturer's warnings about the use and disposal of oil products. Used oil can be a threat to the environment.
10-12 Vehicle Care How to Inspect the Engine Air Cleaner/Filter 2. Disconnect the cover fitting from the ventilation tube (A). 6. Remove the housing cover (C) with outlet duct. To inspect the air cleaner/filter, remove the filter from the vehicle and lightly shake the filter (away from vehicle) to release loose dust and dirt. If the filter remains caked with dirt, a new filter is required. 3. Disconnect the wiring harness connector from the sensor (B). 7.
Vehicle Care Notice: If the air cleaner/filter is off, dirt can easily get into the engine, which could damage it. Always have the air cleaner/filter in place when you are driving. Cooling System The cooling system allows the engine to maintain the correct working temperature. { WARNING An electric engine cooling fan under the hood can start up even when the engine is not running and can cause injury. Keep hands, clothing, and tools away from any underhood electric fan.
10-14 Vehicle Care What to Use { WARNING Adding only plain water to the cooling system can be dangerous. Plain water, or some other liquid such as alcohol, can boil before the proper coolant mixture will. The vehicle's coolant warning system is set for the proper coolant mixture. With plain water or the wrong mixture, the engine could get too hot but you would not get the overheat warning. The engine could catch fire and you or others could be burned.
Vehicle Care Checking Coolant How to Add Coolant to the Recovery Tank The vehicle must be on a level surface when checking the coolant level. Check to see if coolant is visible in the coolant recovery tank. If the coolant inside the coolant recovery tank is boiling, do not do anything else until it cools down.
10-16 Vehicle Care How to Add Coolant to the Radiator { WARNING An electric engine cooling fan under the hood can start up even when the engine is not running and can cause injury. Keep hands, clothing, and tools away from any underhood electric fan. WARNING (Continued) cooling system and surge tank pressure cap to cool if you ever have to turn the pressure cap. 2. Remove the radiator pressure cap when the cooling system, including the upper radiator hose, is no longer hot.
Vehicle Care 10-17 Notice: If the pressure cap is not tightly installed, coolant loss and possible engine damage may occur. Be sure the cap is properly and tightly secured. Engine Overheating The vehicle has several indicators to warn of engine overheating. 6. Fill the coolant recovery tank to the FULL COLD mark. 7. Reinstall the cap on the coolant recovery tank but leave the radiator pressure cap off. 8. Start the engine and let it run until the upper radiator hose feels warm.
10-18 Vehicle Care If you do decide to lift the hood , make sure the vehicle is parked on a level surface. Then check to see if the engine cooling fans are running. If the engine is overheating, both fans should be running. If they are not, do not continue to run the engine and have the vehicle serviced. Notice: Engine damage from running the engine without coolant is not covered by the warranty. Notice: If the engine catches fire while driving with no coolant, the vehicle can be badly damaged.
Vehicle Care If the overheat warning is displayed with no sign of steam: 1. Turn the air conditioning off. 2. Turn the heater on to the highest temperature and to the highest fan speed. Open the windows as necessary. If there is no sign of steam, idle the engine for three minutes while parked. If the warning is still displayed, turn off the engine until it cools down. Also, see “Overheated Engine Protection Operating Mode” next in this section. 3.
10-20 Vehicle Care When to Check Power Steering Fluid 5. Replace the cap and completely tighten it. It is not necessary to regularly check power steering fluid unless you suspect there is a leak in the system or you hear an unusual noise. A fluid loss in this system could indicate a problem. Have the system inspected and repaired. 6. Remove the cap again and look at the fluid level on the dipstick. How to Check Power Steering Fluid To check the power steering fluid: 1.
Vehicle Care . Open the cap with the washer symbol on it. Add washer fluid until the tank is full. See Engine Compartment Overview on page 10‑6 for reservoir location. Notice: . . When using concentrated washer fluid, follow the manufacturer's instructions for adding water. Do not mix water with ready-to-use washer fluid. Water can cause the solution to freeze and damage the washer fluid tank and other parts of the washer system. Also, water does not clean as well as washer fluid. .
10-22 Vehicle Care Brake linings should always be replaced as complete axle sets. Brake Pedal Travel See your dealer/retailer if the brake pedal does not return to normal height, or if there is a rapid increase in pedal travel. This could be a sign that brake service might be required. Brake Adjustment Every time the brakes are applied, with or without the vehicle moving, the brakes adjust for wear. new, approved replacement parts. If this is not done, the brakes might not work properly.
Vehicle Care { WARNING { WARNING If too much brake fluid is added, it can spill on the engine and burn, if the engine is hot enough. You or others could be burned, and the vehicle could be damaged. Add brake fluid only when work is done on the brake hydraulic system. With the wrong kind of fluid in the brake hydraulic system, the brakes might not work well. This could cause a crash. Always use the proper brake fluid. When the brake fluid falls to a low level, the brake warning light comes on.
10-24 Vehicle Care Vehicle Storage { WARNING Batteries have acid that can burn you and gas that can explode. You can be badly hurt if you are not careful. See Jump Starting on page 10‑80 for tips on working around a battery without getting hurt. Infrequent Usage: Remove the black, negative (−) cable from the battery to keep the battery from running down. Extended Storage: Remove the black, negative (−) cable from the battery or use a battery trickle charger.
Vehicle Care Automatic Transmission Shift Lock Control System Check { WARNING When you are doing this inspection, the vehicle could move suddenly. If the vehicle moves, you or others could be injured. 1. Before starting this check, be sure there is enough room around the vehicle. It should be parked on a level surface. 2. Firmly apply the parking brake. See Parking Brake on page 9‑29. Be ready to apply the regular brake immediately if the vehicle begins to move. 3.
10-26 Vehicle Care Park Brake and P (Park) Mechanism Check { WARNING When you are doing this check, the vehicle could begin to move. You or others could be injured and property could be damaged. Make sure there is room in front of the vehicle in case it begins to roll. Be ready to apply the regular brake at once should the vehicle begin to move. Park on a fairly steep hill, with the vehicle facing downhill. Keeping your foot on the regular brake, set the parking brake. . .
Vehicle Care Backglass Wiper Blade 3. Replace the wiper blade. To replace the backglass wiper blade: 4. Return the wiper arm and blade assembly to the rest position on the glass. 1. Pull the wiper blade assembly away from the backglass. The backglass wiper blade will not lock in a vertical position so care should be used when pulling it away from the vehicle. 2. Press the button in the middle of the wiper arm connector and pull the wiper blade away from the arm connector. 3.
10-28 Vehicle Care Headlamp Aiming Bulb Replacement Headlamp aim has been preset at the factory and should need no further adjustment. For the proper type of replacement bulbs, see Replacement Bulbs on page 10‑30. However, if your vehicle is damaged in a crash, the headlamp aim may be affected. Aim adjustment to the low-beam headlamps may be necessary if oncoming drivers flash their high-beam headlamps at you (for vertical aim).
Vehicle Care Taillamps, Turn Signal, Sidemarker, and Stoplamps 10-29 3. Remove the two hex nuts holding the taillamp assembly in place. License Plate Lamp 4. Pull out the taillamp assembly. 1. Remove the two screws holding each of the license plate lamps to the liftgate trim. 5. Turn the bulb socket counterclockwise and pull it straight out to remove it. To replace one of these bulbs: 6. Replace the bulb. 7. Reverse steps 3 through 5 to reinstall the taillamp assembly. A. Taillamp B.
10-30 Vehicle Care 3. Turn the bulb socket counterclockwise and pull the bulb straight out of the socket. 4. Install the new bulb. 5. Reverse steps 1 through 3 to reinstall the license plate lamp. Replacement Bulbs Exterior Lamp Bulb Number License Plate Lamp 194 Rear Sidemarker Lamp 194 Rear Turn Signal and Taillamps 7443 (W21/5W) For replacement bulbs not listed here, contact your dealer/retailer.
Vehicle Care Headlamp Wiring An electrical overload may cause the lamps to go on and off, or in some cases to remain off. Have the headlamp wiring checked right away if the lamps go on and off or remain off. Windshield Wipers If the wiper motor overheats due to heavy snow or ice, the windshield wipers will stop until the motor cools and will then restart. Although the circuit is protected from electrical overload, overload due to heavy snow or ice, may cause wiper linkage damage.
10-32 Vehicle Care Fuses Usage BATT 1 Battery 1 BATT 2 Battery 2 BATT 3 Battery 3 ECM Engine Control Module ECM 1 Engine Control Module 1 EMISSION 1 Emission 1 EMISSION 2 Emission 2 EVEN COILS Even Injector Coils Fuses A/C CLUTCH ABS MTR AFS Usage Air Conditioning Clutch Antilock Braking System (ABS) Motor Adaptive Forward Lighting System Fuses AIRBAG Usage Airbag System AUX POWER Auxiliary Power FAN 1 Cooling Fan 1 FAN 2 Cooling Fan 2 FOG LAMP Fog Lamps FSCM Fuel System Control Mo
Vehicle Care Fuses Usage Heating, Ventilation and Air HVAC BLWR Conditioning Blower LT HI BEAM Left High-Beam Headlamp Left Low‐Beam LT LO BEAM Headlamp Fuses Usage REAR CAMERA Rear Camera RR APO Rear Accessory Power Outlet RR DEFOG Rear Defogger RR HVAC Rear Climate Control System LT PRK Left Parking Lamp Right High‐Beam RT HI BEAM Headlamp LT TRLR STOP/TRN Trailer Left Stoplamp and Turn Signal RT LO BEAM ODD COILS Odd Injector Coils RT PRK PCM IGN Powertrain Control Module Ignitio
10-34 Vehicle Care Relays Usage A/C CMPRSR CLTCH Air Conditioning Compressor Clutch AUX VAC PUMP Auxiliary Vacuum Pump CRNK Switched Power FAN 1 Cooling Fan 1 FAN 2 Cooling Fan 2 FAN 3 Cooling Fan 3 FOG LAMP Fog Lamps HI BEAM High‐Beam Headlamps HID/ LO BEAM High Intensity Discharge (HID) Low‐Beam Headlamps Relays HORN IGN Usage Horn Ignition Main LT TRLR STOP/TRN Trailer Left Stoplamp and Turn Signal Lamp PRK LAMP Park Lamp PWR/TRN Powertrain RR DEFOG Rear Window Defogger RT
Vehicle Care Fuses AIRBAG AMP BCK/ UP/STOP Amplifier Back‐up Lamp/ Stoplamp Body Control Module CNSTR/ VENT Canister Vent DR/LCK DRL Fuses Airbag BCM CTSY Courtesy HVAC Heating, Ventilation and Air Conditioning INADV/ PWR/LED Inadvertent Power LED INFOTMNT Infotainment LT/TRN/SIG Driver Side Turn Signal MSM Memory Seat Module PDM Power Mirrors, Liftgate Release Door Locks Daytime Running Lamps Usage PWR MODE Power Mode DRL 2 GMC HID Only/Rear Fog Lamps-China Only DSPLY Display R
10-36 Vehicle Care Relays Usage LT/ PWR/SEAT Driver Side Power Seat Relay UNLCK RT/ PWR/SEAT Passenger Side Power Seat Relay DRL2 PWR/WNDW Power Windows Relay LT/UNLCK PWR/ COLUMN Power Steering Column Relay DRL L/GATE LCK Liftgate Relay Power Lock Relay Rear Window REAR/WSW Washer Relay Relay Side Relays SPARE FRT/WSW Usage Power Unlock Relay Daytime Running Lamps 2 Relay Driver Side Unlock Relay Daytime Running Lamps Relay Spare Front Windshield Washer Relay
Vehicle Care Wheels and Tires Tires Your new vehicle comes with high-quality tires made by a leading tire manufacturer. If you ever have questions about your tire warranty and where to obtain service, see your vehicle Warranty booklet for details. For additional information refer to the tire manufacturer. WARNING (Continued) . Underinflated tires pose the same danger as overloaded tires. The resulting accident could cause serious injury. Check all tires frequently to maintain the recommended pressure.
10-38 Vehicle Care and service description. See the “Tire Size” illustration later in this section for more detail. (B) TPC Spec (Tire Performance Criteria Specification): Original equipment tires designed to GM's specific tire performance criteria have a TPC specification code molded onto the sidewall. GM's TPC specifications meet or exceed all federal safety guidelines.
Vehicle Care (B) Temporary Use Only: The compact spare tire or temporary use tire has a tread life of approximately 5 000 km (3,000 miles) and should not be driven at speeds over 105 km/h (65 mph). The compact spare tire is for emergency use when a regular road tire has lost air and gone flat. If your vehicle has a compact spare tire, see Compact Spare Tire on page 10‑79 and If a Tire Goes Flat on page 10‑58.
10-40 Vehicle Care Tire Designations Tire Size The following illustration shows an example of a typical passenger vehicle tire size. (A) Passenger (P‐Metric) Tire: The United States version of a metric tire sizing system. The letter P as the first character in the tire size means a passenger vehicle tire engineered to standards set by the U.S. Tire and Rim Association. (B) Tire Width: The three‐digit number indicates the tire section width in millimeters from sidewall to sidewall.
Vehicle Care Accessory Weight: This means the combined weight of optional accessories. Some examples of optional accessories are, automatic transmission, power steering, power brakes, power windows, power seats, and air conditioning. Aspect Ratio: The relationship of a tire's height to its width. Belt: A rubber coated layer of cords that is located between the plies and the tread. Cords may be made from steel or other reinforcing materials.
10-42 Vehicle Care GAWR RR: Gross Axle Weight Rating for the rear axle. See Vehicle Load Limits on page 9‑12. Intended Outboard Sidewall : The side of an asymmetrical tire, that must always face outward when mounted on a vehicle. Kilopascal (kPa): The metric unit for air pressure. Light Truck (LT‐Metric) Tire: A tire used on light duty trucks and some multipurpose passenger vehicles. Load Index: An assigned number ranging from 1 to 279 that corresponds to the load carrying capacity of a tire.
Vehicle Care Radial Ply Tire: A pneumatic tire in which the ply cords that extend to the beads are laid at 90 degrees to the centerline of the tread. Rim: A metal support for a tire and upon which the tire beads are seated. Sidewall: The portion of a tire between the tread and the bead. Speed Rating: An alphanumeric code assigned to a tire indicating the maximum speed at which a tire can operate. Traction: The friction between the tire and the road surface. The amount of grip provided.
10-44 Vehicle Care Tire Pressure Tires need the correct amount of air pressure to operate effectively. If your tires have too much air (over‐inflation), you can get the following: . Unusual wear Notice: Do not let anyone tell . Poor handling you that under‐inflation or over‐inflation is all right. It is not. If your tires do not have enough air (under‐inflation), you can get the following: . Rough ride . Needless damage from road hazards . Too much flexing . Too much heat .
Vehicle Care How to Check Use a good quality pocket-type gauge to check tire pressure. You cannot tell if your tires are properly inflated simply by looking at them. Radial tires may look properly inflated even when they are under‐inflated. Check the tire's inflation pressure when the tires are cold. Cold means your vehicle has been sitting for at least three hours or driven no more than 1.6 km (1 mile). Remove the valve cap from the tire valve stem.
10-46 Vehicle Care Please note that the TPMS is not a substitute for proper tire maintenance, and it is the driver's responsibility to maintain correct tire pressure, even if under‐inflation has not reached the level to trigger illumination of the TPMS low tire pressure telltale. Your vehicle has also been equipped with a TPMS malfunction indicator to indicate when the system is not operating properly. The TPMS malfunction indicator is combined with the low tire pressure telltale.
Vehicle Care the driver. For additional information and details about the DIC operation and displays see Driver Information Center (DIC) on page 5‑25 and Tire Messages on page 5‑37. When a low tire pressure condition is detected, the TPMS illuminates the low tire pressure warning light located on the instrument panel cluster. If the warning light comes on, stop as soon as possible and inflate the tires to the recommended pressure shown on the tire loading information label.
10-48 Vehicle Care TPMS Malfunction Light and Message The TPMS will not function properly if one or more of the TPMS sensors are missing or inoperable. When the system detects a malfunction, the low tire warning light flashes for about one minute and then stays on for the remainder of the ignition cycle. A DIC warning message is also displayed. The low tire warning light and DIC warning message come on at each ignition cycle until the problem is corrected.
Vehicle Care TPMS Sensor Matching Process Each TPMS sensor has a unique identification code. Any time you rotate your vehicle's tires or replace one or more of the TPMS sensors, the identification codes will need to be matched to the new tire/wheel position. The sensors are matched to the tire/wheel positions in the following order: driver side front tire, passenger side front tire, passenger side rear tire, and driver side rear tire using a TPMS diagnostic tool. See your dealer/retailer for service.
10-50 Vehicle Care 8. Proceed to the driver side rear tire, and repeat the procedure in Step 5. The horn sounds two times to indicate the sensor identification code has been matched to the driver side rear tire, and the TPMS sensor matching process is no longer active. The TIRE LEARNING ACTIVE message on the DIC display screen goes off. 9. Turn the ignition switch to LOCK/OFF. 10. Set all four tires to the recommended air pressure level as indicated on the Tire and Loading Information label. 11.
Vehicle Care If the vehicle has a compact spare tire, do not include it in the tire rotation. After the tires have been rotated, adjust the front and rear inflation pressures as shown on the Tire and Loading Information label. See Tire Pressure on page 10‑44 and Vehicle Load Limits on page 9‑12. Reset the Tire Pressure Monitor System. See Tire Pressure Monitor Operation on page 10‑46. Make certain that all wheel nuts are properly tightened.
10-52 Vehicle Care The vehicle needs new tires if any of the following statements are true: . You can see the indicators at three or more places around the tire. . You can see cord or fabric showing through the tire's rubber. . The tread or sidewall is cracked, cut, or snagged deep enough to show cord or fabric. . The tire has a bump, bulge, or split. . The tire has a puncture, cut, or other damage that cannot be repaired well because of the size or location of the damage.
Vehicle Care See Tire Inspection on page 10‑50 and Tire Rotation on page 10‑50 for information on proper tire rotation. { WARNING Mixing tires could cause you to lose control while driving. If you mix tires of different sizes, brands, or types (radial and bias-belted tires), the vehicle may not handle properly, and you could have a crash. Using tires of different sizes, brands, or types may also cause damage to your vehicle. Be sure to use the correct size, brand, and type of tires on all wheels.
10-54 Vehicle Care Different Size Tires and Wheels If you add wheels or tires that are a different size than your original equipment wheels and tires, this could affect the way your vehicle performs, including its braking, ride and handling characteristics, stability, and resistance to rollover. Additionally, if your vehicle has electronic systems such as anti‐lock brakes, rollover airbags, traction control, and electronic stability control, the performance of these systems can be affected.
Vehicle Care The grades are molded on the sidewalls of most passenger car tires. The Uniform Tire Quality Grading (UTQG) system does not apply to deep tread, winter-type snow tires, space-saver, or temporary use spare tires, tires with nominal rim diameters of 10 to 12 inches (25 to 30 cm), or to some limited-production tires.
10-56 Vehicle Care Temperature – A, B, C The temperature grades are A (the highest), B, and C, representing the tire's resistance to the generation of heat and its ability to dissipate heat when tested under controlled conditions on a specified indoor laboratory test wheel. Sustained high temperature can cause the material of the tire to degenerate and reduce tire life, and excessive temperature can lead to sudden tire failure.
Vehicle Care { WARNING Using the wrong replacement wheels, wheel bolts, or wheel nuts on your vehicle can be dangerous. It could affect the braking and handling of your vehicle, make your tires lose air and make you lose control. You could have a collision in which you or others could be injured. Always use the correct wheel, wheel bolts, and wheel nuts for replacement.
10-58 Vehicle Care If a Tire Goes Flat It is unusual for a tire to blowout while you are driving, especially if you maintain your vehicle's tires properly. If air goes out of a tire, it is much more likely to leak out slowly. But if you should ever have a blowout, here are a few tips about what to expect and what to do: If a front tire fails, the flat tire creates a drag that pulls the vehicle toward that side. Take your foot off the accelerator pedal and grip the steering wheel firmly.
Vehicle Care WARNING (Continued) To be certain the vehicle will not move, put blocks at the front and rear of the tire farthest away from the one being changed. That would be the tire on the other side, at the opposite end of the vehicle. This vehicle may come with a jack and spare tire or a tire sealant and compressor kit. To use the jacking equipment to change a spare tire safely, follow the instructions below. Then see Tire Changing on page 10‑67.
10-60 Vehicle Care { WARNING Over-inflating a tire could cause the tire to rupture and you or others could be injured. Be sure to read and follow the tire sealant and compressor kit instructions and inflate the tire to its recommended pressure. Do not exceed the recommended pressure. { WARNING Storing the tire sealant and compressor kit or other equipment in the passenger compartment of the vehicle could cause injury. In a sudden stop or collision, loose equipment could strike someone.
Vehicle Care Tire Sealant Read and follow the safe handling instructions on the label adhered to the sealant canister. A. Selector Switch (Sealant/Air or Air Only) B. On/Off Button C. Pressure Gage D. Pressure Deflation Button (If equipped) E. Tire Sealant Canister F. Sealant/Air Hose (Clear) G. Air Only Hose (Black) H. Power Plug Check the tire sealant expiration date on the sealant canister. The sealant canister should be replaced before its expiration date.
10-62 Vehicle Care 2. Unwrap the sealant/air hose (F) and the power plug (H). 3. Place the kit on the ground. Make sure the tire valve stem is positioned close to the ground so the hose will reach it. 4. Remove the valve stem cap from the flat tire by turning it counterclockwise. When using the tire sealant and compressor kit during cold temperatures, warm the kit in a heated environment for 5 minutes. This will help to inflate the tire faster. Always do a safety check first.
Vehicle Care 10. Inflate the tire to the recommended inflation pressure using the pressure gauge (C). The recommended inflation pressure can be found on the Tire and Loading Information label. See Tire Pressure on page 10‑44. The pressure gauge (C) may read higher than the actual tire pressure while the compressor is on. Turn the compressor off to get an accurate pressure reading. The compressor may be turned on/off until the correct pressure is reached.
10-64 Vehicle Care 19. Stop at a safe location and check the tire pressure. Refer to Steps 1 through 11 under “Using the Tire Sealant and Compressor Kit without Sealant to Inflate a Tire (Not Punctured).” If the tire pressure has fallen more than 10 psi (68 kPa) below the recommended inflation pressure, stop driving the vehicle. The tire is too severely damaged and the tire sealant cannot seal the tire. See Roadside Assistance Program on page 13‑6.
Vehicle Care Always do a safety check first. See If a Tire Goes Flat on page 10‑58. 1. Remove the tire sealant and compressor kit from its storage location. See Storing the Tire Sealant and Compressor Kit on page 10‑67. 2. Unwrap the air only hose (G) and the power plug (H). 3. Place the kit on the ground. Make sure the tire valve stem is positioned close to the ground so the hose will reach it. 10-65 4. Remove the tire valve stem cap from the flat tire by turning it counterclockwise. 8.
10-66 Vehicle Care If you inflate the tire higher than the recommended pressure you can adjust the excess pressure by pressing the pressure deflation button (D), if equipped, until the proper pressure reading is reached. This option is only functional when using the air only hose (G). 14. Replace the air only hose (G) and the power plug (H) and cord back in its original location. Removal and Installation of the Sealant Canister 15. Place the equipment in the original storage location in the vehicle.
Vehicle Care Storing the Tire Sealant and Compressor Kit The tire sealant and compressor kit is located in the storage compartment on the driver side, at the rear of the vehicle. 10-67 2. Press the two tabs on the quick release buckle to release the tire sealant and compressor kit strap. 3. Remove the sealant and compressor kit from its tray. To store the tire sealant and compressor kit, reverse the steps. Tire Changing 1.
10-68 Vehicle Care 1. Open the storage compartment door of the convenience center that is nearest the liftgate and remove the cap on the bottom of the storage compartment. 2. Open the carpet cutout that is located through the hole of the storage compartment. 3. Attach the lug wrench into the hoist shaft. The tools you will be using include the jack (A) and lug wrench (B). A. Rear Convenience Center Removing the Spare Tire C.
Vehicle Care 6. Turn the wrench clockwise to raise the cable back up after removing the spare tire. Do not store a full‐size or a flat road tire under the vehicle. See “Storing a Flat or Spare Tire and Tools” later in this section. To continue changing the flat tire, see “Removing the Flat Tire and Installing the Spare Tire” later in this section. 10-69 Do the following to check the cable: 1. Check under the vehicle to see if the cable is visible. 2.
10-70 Vehicle Care 5. If you still cannot lower the spare tire to the ground, see Secondary Latch System on page 10‑77. If the vehicle has aluminum wheels, remove the wheel nut caps using the wheel wrench. Removing the Flat Tire and Installing the Spare Tire 1. Do a safety check before proceeding. See If a Tire Goes Flat on page 10‑58 for more information. 2. If the vehicle has a wheel cover, loosen the plastic nut caps with the wheel wrench. They will not come off.
Vehicle Care Notice: If a jack is used to raise the vehicle without positioning it correctly, the vehicle could be damaged. When raising the vehicle on a jack, avoid contact with the rear axle control arms. 5. Do not raise the vehicle yet. Put the compact spare tire near you. { WARNING Getting under a vehicle when it is jacked up is dangerous. If the vehicle slips off the jack, you could be badly injured or killed. Never get under a vehicle when it is supported only by a jack.
10-72 Vehicle Care { WARNING 9. Remove the plastic spare tire heat shield by pulling the rubber latch. Store the plastic spare tire heat shield. See “Storing a Flat or Spare Tire and Tools” later in this section for more information. Rust or dirt on a wheel, or on the parts to which it is fastened, can make wheel nuts become loose after time. The wheel could come off and cause an accident. When changing a wheel, remove any rust or dirt from places where the wheel attaches to the vehicle.
Vehicle Care 12. Put the nuts on by hand by turning them clockwise until the wheel is held against the mounting surface. Make sure the rounded end is toward the wheel. 13. Lower the vehicle by attaching the lug wrench to the jack and turning the wrench counterclockwise. Lower the jack completely. 10-73 { WARNING Wheel nuts that are improperly or incorrectly tightened can cause the wheels to become loose or come off.
10-74 Vehicle Care Storing the Spare Tire { WARNING The underbody-mounted spare tire needs to be stored with the valve stem pointing down. If the spare tire is stored with the valve stem pointing upwards, the secondary latch will not work properly and the spare tire could loosen and suddenly fall from the vehicle. If this happened when the vehicle was being driven, the tire might contact a person or another vehicle, causing injury and damage to itself.
Vehicle Care 10-75 3. Put the flat tire in the rear storage area with the valve stem pointing toward the rear of the vehicle. 6. Make sure the tire is stored securely. Push, pull (A), and then try to turn (B) the tire. If the tire moves, use the lug wrench to tighten the cable. Storing the Flat Tire 1. Remove the cable package from the jack storage area. 2. Remove the small center cap by tapping the back of the cap with the extension of the shaft, if the vehicle has aluminum wheels. 5.
10-76 Vehicle Care Storing the Tools 3. Reinstall the wing bolt (B) by turning clockwise. 4. To replace the cover, line up the tab at the front of the cover with the notch in the cover opening. Push the cover in place and make sure that the rear clips are in the slots and push the cover closed. 8. Make sure the metal tube is centered at the striker. Push the tube toward the front of the vehicle. A. Tool Bag 9. Close the liftgate and make sure it is latched properly. C. Jack B.
Vehicle Care Secondary Latch System This vehicle has an underbody mounted tire hoist assembly that has a secondary latch system. It is designed to stop the compact spare tire from suddenly falling off the vehicle if the cable holding the spare tire is damaged. For the secondary latch to work, the tire must be stowed with the valve stem pointing down. See Tire Changing on page 10‑67 for instructions on storing the spare tire correctly. { WARNING Before beginning this procedure read all the instructions.
10-78 Vehicle Care 9. Tilt the retainer and slip it through the wheel opening when the spare tire has been completely lowered. 5. Turn the lug wrench clockwise to raise the jack until it lifts the secondary latch spring. 6. Keep raising the jack until the spare tire stops moving upward and is held firmly in place. This lets you know that the secondary latch has released and the spare tire is balancing on the jack. 10. Turn the lug wrench clockwise to raise the cable back up if the cable is hanging. 8.
Vehicle Care Compact Spare Tire { WARNING Driving with more than one compact spare tire at a time could result in loss of braking and handling. This could lead to a crash and you or others could be injured. Use only one compact spare tire at a time. The compact spare tire, if the vehicle has one, was fully inflated when the vehicle was new, however, it can lose air after a time. Check the inflation pressure regularly. It should be 60 psi (420 kPa).
10-80 Vehicle Care Jump Starting If the vehicle's battery has run down, you may want to use another vehicle and some jumper cables to start your vehicle. Be sure to use the following steps to do it safely. { WARNING Batteries can hurt you. They can be dangerous because: . They contain acid that can burn you. . They contain gas that can explode or ignite. . They contain enough electricity to burn you. If you do not follow these steps exactly, some or all of these things can hurt you.
Vehicle Care 4. Open the hoods and locate the positive (+) and negative (−) terminal locations on the other vehicle. Your vehicle has a remote positive (+) and a remote negative (−) jump starting terminal. See Engine Compartment Overview on page 10‑6 for more information on the terminal locations. { WARNING Using a match near a battery can cause battery gas to explode. People have been hurt doing this, and some have been blinded. Use a flashlight if you need more light.
10-82 Vehicle Care 8. Now connect the black negative (−) cable to the negative (−) terminal of the good battery. Use a remote negative (−) terminal if the vehicle has one. 6. Connect the red positive (+) cable to the positive (+) terminal of the dead battery. Use a remote positive (+) terminal if the vehicle has one. 7. Do not let the other end touch metal. Connect it to the positive (+) terminal of the good battery. Use a remote positive (+) terminal if the vehicle has one.
Vehicle Care 10. Now start the vehicle with the good battery and run the engine for a while. To disconnect the jumper cables from both vehicles, do the following: 1. Disconnect the black negative (−) cable from the vehicle that had the dead battery. 11. Try to start the vehicle that had the dead battery. If it will not start after a few tries, it probably needs service. Notice: If the jumper cables are connected or removed in the wrong order, electrical shorting may occur and damage the vehicle.
10-84 Vehicle Care Towing Towing the Vehicle To avoid damage, the disabled vehicle should be towed with all four wheels off the ground. Consult your dealer/retailer or a professional towing service if the disabled vehicle must be towed. dolly towing. Dinghy towing is towing the vehicle with all four wheels on the ground. Dolly towing is towing the vehicle with two wheels on the ground and two wheels up on a device known as a dolly.
Vehicle Care If the vehicle is all‐wheel‐drive, it can be dinghy towed from the front. These vehicles can also be towed by placing them on a platform trailer with all four wheels off of the ground. These vehicles cannot be towed using a dolly. For vehicles being dinghy towed, the vehicle should be run at the beginning of each day and at each RV fuel stop for about five minutes. This will ensure proper lubrication of transmission components. Re-install the fuse to start the vehicle.
10-86 Vehicle Care Dolly Towing (All-Wheel‐Drive Vehicles) Dolly Towing (Front-Wheel‐Drive Vehicles Only) 4. Clamp the steering wheel in a straight-ahead position with a clamping device designed for towing. 5. Remove the key from the ignition. 6. Secure the vehicle to the dolly. 7. Release the parking brake. Towing the Vehicle From the Rear All-wheel‐drive vehicles must not be towed with two wheels on the ground.
Vehicle Care Appearance Care Exterior Care Cleaning Exterior Lamps/ Lenses Use only lukewarm or cold water, a soft cloth and a car washing soap to clean exterior lamps and lenses. Follow instructions under “Washing the Vehicle” later in this section. Notice: Towing the vehicle from the rear could damage it. Also, repairs would not be covered by the vehicle warranty. Never have the vehicle towed from the rear. Do not tow the vehicle from the rear.
10-88 Vehicle Care Protecting Exterior Bright Metal Parts Bright metal parts should be cleaned regularly to keep their luster. Wash with water or use chrome polish on chrome or stainless steel trim, if necessary. Use special care with aluminum trim. To avoid damaging protective trim, never use auto or chrome polish, steam or caustic soap to clean aluminum. A coating of wax, rubbed to high polish, is recommended for all bright metal parts.
Vehicle Care Wheels and Trim — Aluminum or Chrome The vehicle may have either aluminum or chrome-plated wheels. Keep the wheels clean using a soft clean cloth with mild soap and water. Rinse with clean water. After rinsing thoroughly, dry with a soft clean towel. A wax may then be applied. Notice: Chrome wheels and other chrome trim may be damaged if the vehicle is not washed after driving on roads that have been sprayed with magnesium, calcium or sodium chloride.
10-90 Vehicle Care Wipers can be damaged by: . Extreme dusty conditions . Sand and salt . Heat and sun . Snow and ice, without proper removal Tires Use a stiff brush with tire cleaner to clean the tires. Notice: Using petroleum-based tire dressing products on the vehicle may damage the paint finish and/or tires. When applying a tire dressing, always wipe off any overspray from all painted surfaces on the vehicle.
Vehicle Care Chemical Paint Spotting Some weather and atmospheric conditions can create a chemical fallout. Airborne pollutants can fall upon and attack painted surfaces on the vehicle. This damage can take two forms: blotchy, ring-shaped discolorations, and small, irregular dark spots etched into the paint surface. Interior Care The vehicle's interior will continue to look its best if it is cleaned often.
10-92 . Vehicle Care Use only mild, neutral-pH soaps. Avoid laundry detergents or dishwashing soaps with degreasers. Using too much soap will leave a residue that leaves streaks and attracts dirt. For liquid cleaners, about 20 drops per 3.78 L (1 gal) of water is a good guide. . Do not heavily saturate the upholstery while cleaning. . Damage to the vehicle's interior may result from the use of many organic solvents such as naptha, alcohol, etc.
Vehicle Care If any of the soil remains, a commercial fabric cleaner or spot lifter may be necessary. Test a small hidden area for colorfastness before using a commercial upholstery cleaner or spot lifter. If the locally cleaned area gives any impression that a ring formation may result, clean the entire surface. A paper towel can be used to blot excess moisture from the fabric or carpet after the cleaning process. Leather To remove dust, a soft cloth dampened with water can be used.
10-94 Vehicle Care Some commercial products may increase gloss on the instrument panel. The increase in gloss may cause annoying reflections in the windshield and even make it difficult to see through the windshield under certain conditions. Care of Safety Belts Keep belts clean and dry. { WARNING Do not bleach or dye safety belts. It may severely weaken them. In a crash, they might not be able to provide adequate protection. Clean safety belts only with mild soap and lukewarm water.
Service and Maintenance Service and Maintenance General Information General Information . . . . . . . . . . 11-1 Scheduled Maintenance Scheduled Maintenance . . . . . 11-2 Recommended Fluids, Lubricants, and Parts Recommended Fluids and Lubricants . . . . . . . . . . . . . . . . . . 11-7 Maintenance Replacement Parts . . . . . . . . . . . . . . . . . . . . . . . 11-9 Maintenance Records Maintenance Records . . . . . .
11-2 Service and Maintenance { WARNING Performing maintenance work can be dangerous. Some jobs can cause serious injury. Perform maintenance work only if you have the required know-how and the proper tools and equipment. If in doubt, see your dealer/ retailer to have a qualified technician do the work. See Doing Your Own Service Work on page 10‑4. At your General Motors dealer/ retailer, you can be certain that you will receive the highest level of service available.
Service and Maintenance . 11-3 Brake system inspection (or every 12 months, whichever occurs first). If the engine oil life system is reset accidentally, service the vehicle within 5 000 km/3,000 miles since the last service. Reset the oil life system whenever the oil is changed. See Engine Oil Life System on page 10‑10. Maintenance I . Engine coolant level check. See Engine Coolant on page 10‑13. . Perform all services described in Maintenance I.
11-4 . . . Service and Maintenance Body hinges and latches, key lock cylinders, hood latch assemblies, secondary latches, pivots, spring anchor and release pawl, hood and door hinges, rear folding seats, and liftgate hinges lubrication. See Recommended Fluids and Lubricants on page 11‑7. More frequent lubrication may be required when vehicle is exposed to a corrosive environment. Applying silicone grease on weatherstrips with a clean cloth makes them last longer, seal better, and not stick or squeak.
Service and Maintenance First Engine Oil Change After Every 40 000 km/25,000 Miles . or delivery service. During any maintenance, if a power washer is used to clean mud and dirt from the underbody, care should be taken to not directly spray the transfer case output seals. High pressure water can overcome the seals and contaminate the transfer case fluid. Contaminated fluid will decrease the life of the transfer case and should be replaced. Fuel system inspection for damage or leaks.
11-6 Service and Maintenance Service Maintenance I Maintenance II Change engine oil and filter. Reset oil life system. • • Engine coolant level check. • • Windshield washer fluid level check. • • Tire inflation pressures check. • • Tire wear inspection. • • Rotate tires. • • Fluids visual leak check. • • Engine air cleaner filter inspection (vehicles driven in dusty conditions only). • • Brake system inspection. • • Steering and suspension inspection.
Service and Maintenance Recommended Fluids, Lubricants, and Parts Recommended Fluids and Lubricants Usage Engine Oil Engine Coolant Hydraulic Brake System Windshield Washer Hydraulic Power Steering System Automatic Transmission Carrier Assembly — Differential (Rear Drive Module) and Transfer Case (Power Transfer Unit) Fluid/Lubricant Engine oil which meets GM Standard GM6094M and displays the American Petroleum Institute Certified for Gasoline Engines starburst symbol.
11-8 Service and Maintenance Usage Key Lock Cylinders Hood Latch Assembly, Secondary Latch, Pivots, Spring Anchor, and Release Pawl Hood and Door Hinges and Rear Folding Seat Weatherstrip Conditioning Fluid/Lubricant Multi-Purpose Lubricant, Superlube (GM Part No. U.S. 12346241, in Canada 10953474). Lubriplate Lubricant Aerosol (GM Part No. U.S. 12346293, in Canada 992723) or lubricant meeting requirements of NLGI #2, Category LB or GC-LB. Multi-Purpose Lubricant, Superlube (GM Part No. U.S.
Service and Maintenance 11-9 Maintenance Replacement Parts Replacement parts identified below by name, part number, or specification can be obtained from your dealer/retailer. Part GM Part Number ACDelco Part Number Engine Air Cleaner/Filter 15278634 A3083C Engine Oil Filter 89017524 PF48 Spark Plugs 12611882 41-107 Front Driver – 62.5 cm (24.6 in) 15254805 — Front Passenger – 53.0 cm (20.8 in) 15254804 — Rear – 30.0 cm (11.
11-10 Service and Maintenance Maintenance Records After the scheduled services are performed, record the date, odometer reading, who performed the service, and the type of services performed in the boxes provided. Retain all maintenance receipts.
Service and Maintenance Maintenance Record (cont'd) Date Odometer Reading Serviced By Services Performed 11-11
11-12 Service and Maintenance Maintenance Record (cont'd) Date Odometer Reading Serviced By Services Performed
Technical Data Technical Data Vehicle Identification Vehicle Identification Vehicle Identification Number (VIN) Vehicle Identification Number (VIN) . . . . . . . . . . . . . . 12-1 Service Parts Identification Label . . . . . . . . . . . . . . . . . . . . . . . 12-1 Vehicle Data Capacities and Specifications . . . . . . . . . . . . . . 12-2 Engine Drive Belt Routing . . . 12-3 This legal identifier is in the front corner of the instrument panel, on the left side of the vehicle.
12-2 Technical Data Vehicle Data Capacities and Specifications The following approximate capacities are given in metric and English conversions. See Recommended Fluids and Lubricants on page 11‑7 for more information. Capacities Application Air Conditioning Refrigerant R134a Metric English For the air conditioning system refrigerant charge amount, see the refrigerant caution label located under the hood. See your dealer/retailer for more information. Cooling System 10.8 L 11.
Technical Data Engine Specifications Engine 3.6L V6 Engine Engine Drive Belt Routing 3.6L V6 Engine VIN Code Transmission Spark Plug Gap D Automatic 1.10 mm (0.
12-4 Technical Data 2 NOTES
Customer Information Customer Information Customer Information Customer Satisfaction Procedure . . . . . . . . . . . . . . . . . . 13-1 Customer Assistance Offices (US, Can) . . . . . . . . . . . . . . . . . . 13-3 Customer Assistance for Text Telephone (TTY) Users (US, Can) . . . . . . . . . . . . . . . . . . 13-4 Online Owner Center . . . . . . . . 13-4 GM Mobility Reimbursement Program . . . . . . . . . . . . . . . . . . . . 13-5 Roadside Assistance Program . . . . . . . . . . . . . . . . . . . .
13-2 Customer Information STEP TWO : If after contacting a member of dealership management, it appears your concern cannot be resolved by the dealership without further help, in the U.S., contact the Buick Customer Assistance Center by calling 1-800-521-7300. In Canada, contact General Motors of Canada Customer Communication Centre by calling 1‐800-263-3777 (English) or 1-800-263-7854 (French). We encourage you to call the toll-free number in order to give your inquiry prompt attention.
Customer Information STEP THREE — Canadian Owners: In the event that you do not feel your concerns have been addressed after following the procedure outlined in Steps one and two, General Motors of Canada Limited wants you to be aware of its participation in a no-charge Mediation/Arbitration program. General Motors of Canada Limited has committed to binding arbitration of owner disputes involving factory-related vehicle service claims.
13-4 Customer Information Canada — Customer Assistance General Motors of Canada Limited Customer Communication Centre, CA1-163-005 1908 Colonel Sam Drive Oshawa, Ontario L1H 8P7 www.gmcanada.com 1-800-263-3777 (English) 1-800-263-7854 (French) 1-800-263-3830 (For Text Telephone devices (TTYs)) Roadside Assistance: 1-800-268-6800 Overseas — Customer Assistance Please contact the local General Motors Business Unit. Mexico, Central America and Caribbean Islands/Countries (Except Puerto Rico and U.S.
Customer Information Other Helpful Links: Buick — www.buick.com Buick Merchandise — www.buickmerchandise.com Help Center — www.buick.com/ helpcenter . FAQ . Contact Us My GM Canada (Canada) — www.gm.ca My GM Canada is a password-protected section of www.gm.ca where you can save information on GM vehicles, get personalized offers, and use handy tools and forms with greater ease. Here are a few of the valuable tools and services you will have access to: .
13-6 Customer Information General Motors of Canada also has a Mobility Program. Call 1-800-GM-DRIVE (463-7483) for details. TTY users call 1-800-263-3830. . Model, year, color, and license plate number of the vehicle . Odometer reading, Vehicle Identification Number (VIN), and delivery date of the vehicle Roadside Assistance Program . Description of the problem For U.S. purchased vehicles, call 1-800-252-1112; (Text Telephone (TTY): 1‐888‐889‐2438).
Customer Information . . Flat Tire Change: Service is provided to change a flat tire with the spare tire. The spare tire, if equipped, must be in good condition and properly inflated. It is the owner's responsibility for the repair or replacement of the tire if it is not covered by the warranty. Services Specific to Canadian Purchased Vehicles . Fuel delivery: Reimbursement is approximately $5 Canadian. Diesel fuel delivery may be restricted.
13-8 Customer Information Scheduling Service Appointments Courtesy Transportation Program When your vehicle requires warranty service, contact your dealer/retailer and request an appointment. By scheduling a service appointment and advising your service consultant of your transportation needs, your dealer/ retailer can help minimize your inconvenience.
Customer Information Public Transportation or Fuel Reimbursement If your vehicle requires overnight warranty repairs, and public transportation is used instead of the dealer's shuttle service, the expense must be supported by original receipts and can only be up to the maximum amount allowed by GM for shuttle service. In addition, for U.S. customers, should you arrange transportation through a friend or relative, limited reimbursement for reasonable fuel expenses may be available.
13-10 Customer Information Collision Damage Repair If your vehicle is involved in a collision and it is damaged, have the damage repaired by a qualified technician using the proper equipment and quality replacement parts. Poorly performed collision repairs diminish your vehicle's resale value, and safety performance can be compromised in subsequent collisions.
Customer Information Many insurance policies provide reduced protection to your GM vehicle by limiting compensation for damage repairs by using aftermarket collision parts. Some insurance companies will not specify aftermarket collision parts. When purchasing insurance, we recommend that you assure your vehicle will be repaired with GM original equipment collision parts. If such insurance coverage is not available from your current insurance carrier, consider switching to another insurance carrier.
13-12 Customer Information Managing the Vehicle Damage Repair Process In the event that your vehicle requires damage repairs, GM recommends that you take an active role in its repair. If you have a pre-determined repair facility of choice, take your vehicle there, or have it towed there. Specify to the facility that any required replacement collision parts be original equipment parts, either new Genuine GM parts or recycled original GM parts.
Customer Information Owner Information Owner publications are written specifically for owners and intended to provide basic operational information about the vehicle. The owner manual includes the Maintenance Schedule for all models. ORDER TOLL FREE: 1-800-551-4123 Monday-Friday 8:00 AM - 6:00 PM Eastern Time For Credit Card Orders Only (VISA-MasterCard-Discover), visit Helm, Inc. on the World Wide Web at: helminc.
13-14 Customer Information of vehicles, it may order a recall and remedy campaign. However, NHTSA cannot become involved in individual problems between you, your dealer, or General Motors. To contact NHTSA, you may call the Vehicle Safety Hotline toll-free at 1-888-327-4236 (TTY: 1-800-424-9153); go to http://www.safercar.gov; or write to: Administrator, NHTSA 1200 New Jersey Avenue, S.E. Washington, D.C. 20590 You can also obtain other information about motor vehicle safety from http://www.safercar.gov.
Customer Information Vehicle Data Recording and Privacy Your GM vehicle has a number of sophisticated computers that record information about the vehicle’s performance and how it is driven. For example, your vehicle uses computer modules to monitor and control engine and transmission performance, to monitor the conditions for airbag deployment and deploy airbags in a crash and, if so equipped, to provide antilock braking to help the driver control the vehicle.
13-16 Customer Information GM will not access this data or share it with others except: with the consent of the vehicle owner or, if the vehicle is leased, with the consent of the lessee; in response to an official request of police or similar government office; as part of GM's defense of litigation through the discovery process; or, as required by law.
INDEX A Accessories and Modifications . . . . . . . . . . . . . . . . . 10-3 Accessory Power . . . . . . . . . . . . . . 9-19 Adaptive Forward Lighting (AFL) . . . . . . . . . . . . . . . . . 6-4 Add-On Electrical Equipment . . . . . . . . . . . . . . . . . . . 9-58 Adding Equipment to the Airbag-Equipped Vehicle . . . . . 3-42 Adjustments Lumbar, Front Seats . . . . . . . . . . . 3-4 Air Cleaner/Filter, Engine . . . . . 10-11 Air Vents . . . . . . . . . . . . . . . . . . . . . . .
i-2 INDEX B Battery . . . . . . . . . . . . . . . . . . . . . . . 10-23 Jump Starting . . . . . . . . . . . . . . . 10-80 Load Management . . . . . . . . . . . . . 6-7 Power Protection . . . . . . . . . . . . . . 6-8 Voltage and Charging Messages . . . . . . . . . . . . . . . . . . .5-31 Blade Replacement, Wiper . . . 10-26 Bluetooth . . . . . . . . . . . . . . . . . . . . . . 7-46 Brakes . . . . . . . . . . . . . . . . . . . . . . . . 10-21 Antilock . . . . . . . . . . . . . . . . . . . . . . .
INDEX Circuit Breakers . . . . . . . . . . . . . . 10-31 Cleaning Exterior Care . . . . . . . . . . . . . . . 10-87 Interior Care . . . . . . . . . . . . . . . . 10-91 Climate Control Systems Dual Automatic . . . . . . . . . . . . . . . . 8-1 Rear . . . . . . . . . . . . . . . . . . . . . . 8-7, 8-8 Clock . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-9 Cluster, IP . . . . . . . . . . . . . . . . . . . . . 5-13 Collision Damage Repair . . . . . 13-10 Compact Spare Tire . . . . . . . . . .
i-4 INDEX Drive Systems All-Wheel Drive . . . . . . . 10-24, 9-28 Driver Information Center (DIC) . . . . . . . . . . . . . . . . . 5-25 Driving Characteristics and Towing Tips . . . . . . . . . . . . . . . . .9-47 Defensive . . . . . . . . . . . . . . . . . . . . . . 9-2 Drunk . . . . . . . . . . . . . . . . . . . . . . . . . . 9-2 Highway Hypnosis . . . . . . . . . . . . . 9-8 Hill and Mountain Roads . . . . . . . 9-8 If the Vehicle is Stuck . . . . . . . . . 9-11 Loss of Control . . . . . . . . . . . .
INDEX F Filter Engine Air Cleaner . . . . . . . . . .10-11 Flash-to-Pass . . . . . . . . . . . . . . . . . . . 6-3 Flashers, Hazard Warning . . . . . . 6-4 Flat Tire . . . . . . . . . . . . . . . . . . . . . . 10-58 Flat Tire, Changing . . . . . . . . . . . 10-67 Floor Console Storage . . . . . . . . . . 4-2 Floor Mats . . . . . . . . . . . . . . . . . . . . 10-94 Fluid Automatic Transmission . . . . .10-11 Brakes . . . . . . . . . . . . . . . . . . . . . . 10-22 Power Steering . . . . . . . . . . . . .
i-6 INDEX H Halogen Bulbs . . . . . . . . . . . . . . . . 10-28 Hazard Warning Flashers . . . . . . . 6-4 Head Restraints . . . . . . . . . . . . . . . . 3-2 Headlamps Adaptive Forward Lighting (AFL) . . . . . . . . . . . . . . . . 6-4 Aiming . . . . . . . . . . . . . . . . . . . . . . 10-28 Bulb Replacement . . . . . . . . . . 10-28 Daytime Running Lamps/ Automatic Headlamp System . . . . . . . . . . . . . . . . . . . . . . . 6-3 Delayed . . . . . . . . . . . . . . . . . . . . . . . 6-3 Flash-to-Pass . .
INDEX Lighting Adaptive Forward . . . . . . . . . . . . . . 6-4 Delayed Entry . . . . . . . . . . . . . . . . . 6-6 Delayed Exit . . . . . . . . . . . . . . . . . . . 6-6 Entry . . . . . . . . . . . . . . . . . . . . . . . . . . 6-6 Illumination Control . . . . . . . . . . . . 6-5 Parade Dimming . . . . . . . . . . . . . . . 6-7 Lights Airbag Readiness . . . . . . . . . . . . .5-16 Antilock Brake System (ABS) Warning . . . . . . . . . . . . . .5-22 Charging System . . . . . . . . . . . . .
i-8 INDEX Mirrors Automatic Dimming Rearview . . . . . . . . . . . . . . . . . . . .2-18 Convex . . . . . . . . . . . . . . . . . . . . . . .2-15 Folding . . . . . . . . . . . . . . . . . . . . . . .2-16 Heated . . . . . . . . . . . . . . . . . . . . . . .2-17 Park Tilt . . . . . . . . . . . . . . . . . . . . . .2-17 Power . . . . . . . . . . . . . . . . . . . . . . . .2-16 Monitor System, Tire Pressure . . . . . . . . . . . . . . . . . . . . 10-45 MP3 . . . . . . . . . . . . . . . . . . . . .
INDEX Power (cont.) Seat Adjustment . . . . . . . . . . . . . . . 3-3 Steering Fluid . . . . . . . . . . . . . . . 10-19 Windows . . . . . . . . . . . . . . . . . . . . .2-19 Pregnancy, Using Safety Belts . . . . . . . . . . . . . . . . . . . . . . . . . 3-27 Privacy Radio Frequency Identification (RFID) . . . . . . . 13-16 Program Courtesy Transportation . . . . . .13-8 Proposition 65 Warning, California . . . . . . . . . . . . . . . . . . . . . 10-3 R Radio Frequency Identification (RFID) . . . . . . . .
i-10 INDEX S Safety Belts . . . . . . . . . . . . . . . . . . . 3-13 Care . . . . . . . . . . . . . . . . . . . . . . . . . .3-28 Extender . . . . . . . . . . . . . . . . . . . . . .3-28 How to Wear Safety Belts Properly . . . . . . . . . . . . . . . . . . . . .3-17 Lap-Shoulder Belt . . . . . . . . . . . .3-22 Reminders . . . . . . . . . . . . . . . . . . . .5-16 Replacing After a Crash . . . . . .3-29 Use During Pregnancy . . . . . . . .3-27 Safety Defects Reporting Canadian Government . . . . . .
INDEX Storage Areas (cont.) Convenience Net . . . . . . . . . . . . . . 4-3 Floor Console . . . . . . . . . . . . . . . . . 4-2 Glove Box . . . . . . . . . . . . . . . . . . . . . 4-1 Instrument Panel . . . . . . . . . . . . . . 4-1 Roof Rack System . . . . . . . . . . . . . 4-4 Storing the Tire Sealant and Compressor Kit . . . . . . . . . 10-67 Stuck Vehicle . . . . . . . . . . . . . . . . . . 9-11 Sun Visors . . . . . . . . . . . . . . . . . . . . . 2-21 Sunroof . . . . . . . . . . . . . . . . . . . . . .
i-12 INDEX U Ultrasonic Parking Assist . . . . . . 9-35 Uniform Tire Quality Grading . . . . . . . . . . . . . . . . . . . . . 10-54 Universal Remote System . . . . . 5-47 Operation . . . . . . . . . . . . . . . . . . . . .5-51 Programming . . . . . . . . . . . . . . . . .5-47 Using this Manual . . . . . . . . . . . . . . . . iv V Vehicle Canadian Owners . . . . . . . . . . . . . . .iii Control . . . . . . . . . . . . . . . . . . . . . . . . 9-3 Load Limits . . . . . . . . . . . . . . . . . . .
