Installation Guide

ManualsBrandsBuilders Edge ManualsBuilding materials9 in. Flat Panel Window Header Keystone in 023 Wicker

9" Window Header

Keystone Installation & Cutting Instructions

Kit Contains:

1 pc. Keystone

1 pc. Keystone Base

4 pcs. Screws

Keystone

Keystone Base

Step 2

Measure the width of the window across the

largest measurement to create Dim. "A".

Also, draw a horizontal line 1/8" above the

window trim. This line will be used to

properly space the Window Header from the

window trim. See Figure 1 at right.

Fig. 1

Dim "A"

Draw horizontal line 1/8"

above window trim

Step 3A

If your window doesn't match the exact size of

the Window Header right from the box, the

Window Header will need to be cut. With the

Window Header and Window Header Base

assembled, mark the center on the assembly.

See Figure 2A at right.

Dim "B"

Window Header and Base

assembly right from box.

Fig. 2A

8-7-01

PAPC9414

I-0068

Step 3B

Next, subtract Dim. "A" from Dim. "B" and

divide the measurement by 2. This will give

you Dim. "C". See Figure 2B at right.

Dim. "A"

Dim. "B"

Dim. "C"

Step 3C

Transfer Dim. "C" to the Window Header

Assembly. Dim. "C" will be transferred 2

times; once on each side of the centerline.

See Figure 2C at right.

Dim "C"

Fig. 2B

Fig. 2C

NOTE: IF HEADER IS NOT BEING CUT, COMPLETE STEP 1 AND PROCEED TO STEP 7

Step 1

Remove the Keystone and Keystone Base

from the Window Header Assembly. This is

done by disengaging the locking tabs of the

Keystone and removing the screws from the

Keystone Base. See figure above.

Fig. 4

Fig. 5

Step 5

Once the Window Header has been cut to the

correct length, disengage the locking tabs and

remove the Window Header from the Window

Header Base. To release the locks, start at

the open end of the cut Header Assembly and

pull the wall of the Header away from the

Header Base. Continue this process, working

your way to the end of the cut Window Header

Assembly. See Figure 4 at right.

Step 4

Cut the Window Header and Window Header

Base assembly at the lines created by Dim. "C".

See Figure 3 at right.

Line created from Dim. "C"

Fig. 3

Remove shaded area

Step 6

Align the bottom of the Window Header Base to

the line drawn 1/8" above the window trim. Mate

the two cut ends of the Window Header Base to

each other. The preferred method of attaching

the Window Header Base to the house is to use

the Shutter Loks that are enclosed with the

Window Header Kit. In order to install the

Shutter Loks, 1/4" holes must be drilled into the

wall to accept the Shutter Loks. Another method

is to use screws. Use the elongated slots in the

Header Base and attach the tray to the house

using the screws provided with the Window

Header Kit. Be sure not to fasten the screws too

tightly to allow for expansion and contraction.

See Figure 5 at right.

slots for optional

screw application

Fig. 6

Step 7

With the Window Header Bases securely

fastened to the wall, the Window Header can be

snapped into place by engaging the locks. See

Figure 6 at right.

Summary of content (2 pages)

PAGE 1
9" Window Header Step 4 Cut the Window Header and Window Header Base assembly at the lines created by Dim. "C". See Figure 3 at right. Keystone Installation & Cutting Instructions Kit Contains: 1 pc. Keystone 1 pc. Keystone Base 4 pcs. Screws Line created from Dim. "C" CL Line created from Dim. "C" Keystone Base Remove shaded area Fig.
PAGE 2
Step 8 Center the Keystone Base over the Window Header Assembly. The tab at the bottom of the Keystone Base is to aid in installation. The bottom of the tab and the bottom of the Window Header should be flush. Screw the Keystone Base into place using the enclosed screws. See Figure 7 at right. Fig. 7 Note: Shutter Loks may be used to secure the Keystone Base to the Window Header. If Shutter Loks are being used, drill two 1/4" holes through the Window Header and Tray to accept the Shutter Loks.