Installation guide

ManualsBrandsBulldog Security ManualsHome building and Decor721

CONTENTS

REMOTE STARTER MODELS RS92 / RS92E

INSTALLATION GUIDE

•

OWNER’S GUIDE

Technical Assistance

All tech personnel are expertly qualified to answer any technical questions.

Technicians are available Monday through Friday from 9:00 a.m. until 8:00 p.m. and Saturday 10:00 a.m. until 4:00 p.m.

Address

288 Canton Avenue • Wintersville, Ohio 43953

Telephone

Phone: 740-264-4710 • 800-878-8007 • Fax: 740-264-7306

System Features ....................................... 1

System Components ..................................... 1

Required Tools ........................................ 1

Technical Assistance .................................. 1

Before You Begin .................................... 1-2

Precautions........................................... 2

Testing Your Wires .................................... 2

Making Wiring Connections............................ 2-4

Locating & Making Connections........................ 4-5

Connecting the 12-Pin Harness and the 4-Relay Harness...6

Neutral Safety Switch ................................. 6

Antenna Placement (E Models)........................... 7

Anti-Theft System ..................................... 7

Factory Anti-Theft System.............................. 7

How to use Your Remote Transmitter ..................... 7

Programming Instructions .............................. 8

Summary of content (9 pages)

PAGE 1
INSTALLATION GUIDE • OWNER’S GUIDE REMOTE STARTER MODELS RS92 / RS92E CONTENTS System Features ....................................... 1 System Components ..................................... 1 Required Tools ........................................ 1 Technical Assistance .................................. 1 Before You Begin .................................... 1-2 Precautions ........................................... 2 Testing Your Wires ....................................
PAGE 2
SYSTEM FEATURES Four-Button Extended Range Remote Control Remotely start your car to run the heater or air conditioning from an extended distance. Instant Panic Works as personal protection. The horn sounds and the lights flash for 30 seconds. Car Finder The horn will sound and the lights will flash to help you locate your vehicle in a crowded parking lot. Remote Programmable Run Time Remotely program your vehicle to run 5 to 15 minutes.
PAGE 3
Since there are many different makes and models of vehicles, look at the wiring chart on or our website, www.bulldogsecurity.com/wires.htm. Read this manual thoroughly before starting the installation. You must decide if the parking light option is desired. An optional part #775 will be needed. Please do not skip any steps. TACH/TACHLESS OPERATION In most cases the decision to go with tachless mode will save time during the installation. If your vehicle is hard-starting then you should use tach mode.
PAGE 4
3. Separate the vehicle wire as shown. Make the separation large enough to fit the other wire through. 4. Insert the wire from the unit through the hole as shown. 5. Wrap the wire around one side then the other and finally around itself as shown. 1 2 3 6. Use electrical tape to wrap. Be sure to cover the wire about two inches on either side of the connection. First pull the wire that you have just connected along side the wire you connected to, tape and wire tie them together.
PAGE 5
4. Use electrical tape to wrap, be sure to cover about 2 inches on either side of connection. Secure with wire ties as shown. Electrical Tape Wire Tie Wire Tie Use this method ONLY when connecting two separate wires end to end. LOCATING & MAKING CONNECTIONS Please see the wiring chart on our website, www.bulldogsecurity.com.
PAGE 6
CHASSIS GROUND Factory Bolt Locate an easy to get to bolt or screw located under the driver’s side of the dash and attach the BLACK ground wire from the 11-pin Spade Connector harness securely as pictured. PARKING LIGHTS (+12V only with parking lights on) Turn the parking lights to the ON position. (NOT YOUR HEADLAMPS). Probe the wire(s) coming from your headlamp control switch. Find a wire that will show +12V only when the parking lights are ON. Connect the BROWN wire from the 12-pin harness to this wire.
PAGE 7
AUXILIARY INPUT If you wish to use this starter with an aftermarket alarm, connect the BLUE wire from the 12-pin harness to the second or third channel (-) output of your existing alarm. When the output is activated, a (-) signal will be supplied to the remote starter. CONNECTING THE 12-PIN HARNESS & 4-RELAY HARNESS GREEN/BLACK (-) Tach Input BLUE/WHITE (-) To hood pin switch BLUE (-) Aux.
PAGE 8
ANTENNA PLACEMENT ANTENNA For best results, run the antenna (YELLOW WIRE WITH BLACK TIP from the back of the unit) as straight as possible. Do not place the antenna next to any metal parts or the vehicle’s main computer control module. Range is up to 400 feet. Antenna Wire Antenna Tube E MODEL REMOTE STARTERS Run the antenna up the windshield pillar on the Control Module driver’s side and across the top of the windshield to the center, behind the rearview mirror.
PAGE 9
PROGRAMMING INSTRUCTIONS ENTERING PROGRAMMING MODE Make sure your vehicle is not running and the brake is pressed. The brake is to remain pressed as long as you want to remain in programming mode. Adding New Transmitters Press and hold the brake, then press and hold Button #1 (start) on the working transmitter until the parking lights flash once. Release Button #1. Press any button on the new remote, the parking lights will flash three (3) times, the new remote is now programmed.