Creating A Higher Standard JBS Technologies produces the world's most innovative and reliable car alarms, remote starters, keyless entry systems and starter immobilizers. JBS Technologies is not an importing or distribution company. Our products are designed with patented technology and produced in the United States with robotics to insure flawless performance and the highest quality control.
YOUR WARRANTY Thank you for purchasing American made products by JBS Technologies. To order additional transmitters or other accessories, visit our website at wwww.jbstech.com or contact JBS Technologies at the following address: JBS Technologies 225 Technology Way Steubenville, OH 43952 FOR TECHNICAL ASSISTANCE Here's how your warranty works: JBS Technologies warrants to the original customer, and the original car a limited lifetime warranty.
WARRANTY VALIDATION CONTENTS PLEASE FILL OUT THIS FORM AND MAIL IT IN TO REGISTER YOUR WARRANTY System Features .......................... 4 Your Name ________________________________________ System Components........................ 5 Address ________________________________________ Required Tools ........................... 5 ________________________________________ Technical Assistance .................... 5 5-6 Dealer Name ____________________________________ Precautions ..................
SYSTEM FEATURES Four-Button Extended Range Remote Control Remotely start your car to run the heater or air conditioning from an extended distance. Keyless Entry Remotely locks and unlocks your power door locks. Trunk Release Remotely opens your trunk with a push of a button. (Optional part #775 required) Remote Programmable Run Time Remotely program your vehicle to run 5 to 15 minutes. Run Time Confirmation Lets you check the run time that the unit is programmed for.
VEHICLES WITH FACTORY ANTI-THEFT SYSTEMS (CONT.
BEFORE YOU BEGIN cont. It is recommended that a carbon monoxide detector be installed in the living area near the location where the vehicle may be garaged. VEHICLES WITH FACTORY ANTI-THEFT SYSTEMS (CONT.) Manufacturer Since there are many different makes and models of vehicles, look at the wiring chart on our website, www.jbstech.com. Read this manual thoroughly before starting the installation. You must also decide if any options are desired such as trunk release and dome light supervision.
VEHICLES WITH FACTORY ANTI-THEFT SYSTEMS Manufacturer CHRYSLER Make/ Year MALIBU 97+ MONTE CARLO 96-99 MONTE CARLO 2000+ FULL-SIZE PU 98+ S-10 98+ SAVANNAH 98+ SUBURBAN 98+ TAHOE 98+ VAN 98+ VENTURE 99+ CONCORD 98+ LHS 98+ SEBRING CONTV.
MAKING CONNECTIONS cont. MAKING END TO END CONNECTIONS FOLLOW THESE INSTRUCTIONS VEHICLES WITH FACTORY ANTI-THEFT SYSTEMS Manufacturer Acura 1. When tying two separate wires together at their ends, strip back one inch of insulation on both wires and separate the strands of wire as shown below. AUDI 2. Twist upper wires together, twist lower wires together as shown. 3. Lay upper twisted pair of wires over right wire as shown. Bring lower twisted pair of wires up to meet the left wire as shown. 4.
HOW TO USE YOUR REMOTE TRANSMITTER Start BUTTON #1 Starts your vehicle from 400 feet away. (E-Model, up to 800 feet) Lock Unlock BUTTON #2 Locks and unlocks your power door locks. Trunk BUTTON #3 Pops your trunk Stop BUTTON #4 Shuts engine off and programs runtime. Starting the Vehicle with the Remote Transmitter Press and release button #1 (start). The parking lights will flash once, confirming the car starter received the signal.
LOCATING & MAKING CONNECTIONS ACCESSORY WIRE(S) THAT POWER THE HEATER/BLOWER MOTOR (+12V in run or on positions) This wire is also in the main ignition switch harness usually located in the steering column. Make all connections as close to the ignition switch harness as possible. Most vehicles will have (1) accessory wire; however some Fords, newer GM vehicles and Chrysler 94 and up will have (2) or more accessory wires.
OPTIONAL CONNECTIONS LOCATING & MAKING CONNECTIONS TRUNK RELEASE OUTPUT (-) (Optional Part #775 required) Locate the trunk release wire coming from the back of the trunk release switch. To determine if your trunk release is tripped by a (+) positive or a (-) negative (most trunk release switches are (+) positive), place the clip end of your test light to ground, probe the wire. Press the “Trunk” button, if the test light illuminates, you have a (+) positive trunk release.
NEUTRAL SAFETY SWITCH OPTIONAL CONNECTIONS MECHANICAL NEUTRAL SAFETY SWITCH (Rear Wheel Drive Only) When installing a Bulldog remote starter on GM vehicles or Dodge Dakotas built prior to 1996, you must: “Type C” (continued) Use the diagram below to create a circuit that will prevent the remote starter from starting the vehicle unless the key is removed from the ignition switch. PRE-1996 GM REAR WHEEL DRIVES WITH PURPLE CRANK WIRE Optional part #775 required.
OPTIONAL CONNECTIONS CONNECTING DOOR LOCKS CONNECTING THE 18-PIN HARNESS & 4-RELAY HARNESS (Optional) CONNECTING “TYPE A LOCKS” •If your vehicle has a “Type A” door locking system, connect the BROWN WITH BLACK STRIPE wire from the 18-pin harness to the door lock wire. Connect the GREEN WITH BLACK STRIPE wire to the unlock wire. See diagram below.
ANTENNA PLACEMENT OPTIONAL CONNECTIONS ANTENNA For best results, run the antenna (YELLOW WIRE WITH BLACK TIP from the back of the unit) as high up in the dash and as straight as possible. Do not place the antenna next to any metal parts or the vehicle’s main computer control module. Range is up to 400 feet. TESTING: Door Locks E MODEL REMOTE STARTERS Run the antenna up the windshield pillar on the driver’s side and across the top of the windshield to the center, behind the rearview mirror.