Installation manual

ManualsBrandsBulldog Security ManualsAutomotiveINSTALLATION GUIDE

, Inc.

PEDESTRIAN GATE LOCK

Installation Manual

PLEASE NOTE ... due to the variety of possible mounting applications, no mount-

ing hardware for the lock is provided. All necessary mounting hardware can be

obtained at a local hardware store; all other hardware is provided. If you need assis-

tance please call GTO

Technical Service at 800-543-1236.

RB920 … rev- 5/20/03

Contents

• Before You Start ----------------------------------- page 1

• Parts Identification -------------------------------- page 2

• Mounting the Lock -------------------------------- page 3

• Wiring the Control Board------------------------- page 6

• Accessory and Warranty Information ----------- inside back cover

Summary of content (8 pages)

PAGE 1
® , Inc. TM PEDESTRIAN GATE LOCK Installation Manual PLEASE NOTE ... due to the variety of possible mounting applications, no mounting hardware for the lock is provided. All necessary mounting hardware can be obtained at a local hardware store; all other hardware is provided. If you need assistance please call GTO® Technical Service at 800-543-1236.
PAGE 2
Before You Start ... Materials you will need before you begin the installation. • For all installations use mounting hardware (not included) no greater than 5/16” diameter. Note: for a more secure installation, we suggest you use lock washers and/or lock nuts on all mounting hardware. • For most IRON and ALUMINUM TUBE gates (see Illustration C, page 4) use bolts, washers, and nuts to mount both the lock and the receiver.
PAGE 3
Parts Identification H K G J I F E A , Inc. Q L AUTOMATIC SOLENOID SECURITY GATE LOCK B R P (top) P (side) O (top) M C A - Lock w/ 20' of Low Voltage Wire B - Lock Receiver C - Clevis Pin D - Locking Cap E - Control Box F - Lock Control Board G -12 Volt DC Charger H -Battery Lead Wires I - Ten (10) ft. of Low Voltage Wire to connect Entry Device (push button or keypad) to Control Board J - Push Button Entry Control and mounting screws K -12 Volt Battery / 1.
PAGE 4
Mounting The Lock: Step 1: With the gate in the closed position determine the best location for the lock and receiver. Attach the lock to a solid surface or cross member to provide stability. Step 2: Hold receiver and lock together (with receiver pin hole and lock slot aligned) against the gate post and mark positions to drill receiver holes (see Illustration C & D, page 4). The receiver must be mounted with bolts (not u-bolts) to allow lock to seat properly. Secure the receiver to the gate post.
PAGE 5
Illustration C Iron or Aluminum Tube Fence and Gate Installation Remember to check the alignment and mark positions before drilling holes in fence post and gate. Clevis Pin Bulldog Lock Receiver , Inc. ID NO LE CK SO LO TIC TE MA Y GA TO AUCURIT , Inc. SE ID NO LE CK SO LO TIC TE MA Y GA TO AUCURIT SE Locking Cap Carriage bolts, washers & nuts (not provided ...
PAGE 6
Control Box Assembly 1 Press the strain relief into the control box until it clicks securely in place. 2 Press the control board standoffs into the stand-off receivers in the control box. 3 4 Secure the control board to the stand-offs (terminal block down) by placing stand-off pins into holes on control board and pressing board until it snaps securely in place. Battery Terminals 4 Place the battery into control box (battery terminals UP).
PAGE 7
Wiring the Control Board WARNING: DO NOT CONNECT BATTERY LEAD WIRES OR PLUG IN 12 VOLT DC CHARGER UNTIL ALL OTHER WIRES ARE CONNECTED IN THE CONTROL BOX. Step 1: Attach the RED (+) battery lead wire to control board terminal #5 and the BLACK (–) battery wire to control board terminal #2. DO NOT connect battery lead wires to the battery until all other wiring is complete.
PAGE 8
Available Accessories: GTO DIGITAL KEYPAD ... The weatherproof digital keypad for the Bulldog Security Lock can be programmed to use up to fifteen different personal identification number (PIN) codes. Each code is face programmable with additional security features built in. Installation is easy, using 16 gauge, multi-stranded, direct burial low voltage wire. Requires three (3) AA batteries (not included).