Installation guide

ManualsBrandsBulldog Security ManualsHome building and DecorPRO_SERIES 6002

CONTENTS

INSTALLATION GUIDE

•

OWNER’S GUIDE

Technical Assistance

All tech personnel are expertly qualified to answer any technical questions.

Technicians are available Monday through Friday from 9:00 a.m. until 8:00 p.m. and Saturday 10:00 a.m. until 4:00 p.m.

Address

288 Canton Avenue • Wintersville, Ohio 43953

Telephone

Phone: 740-264-4710 • 800-878-8007 • Fax: 740-264-7306

SECURITY SYSTEM

PRO-SERIES 6002

System Features ........................................... 1-2

System Components ........................................... 2

Technical Assistance ........................................ 2

Before You Begin ............................................ 2

Precautions ............................................... 2-3

Making Connections ........................................ 3-4

Locating & Making Connections .............................. 4-6

Optional Connections ........................................ 7

Wiring Diagram .............................................. 8

How to use Your Remote Transmitter ........................... 8

Operating Instructions ................................... 9-10

Summary of content (11 pages)

PAGE 1
INSTALLATION GUIDE • OWNER’S GUIDE SECURITY SYSTEM PRO-SERIES 6002 CONTENTS System Features ........................................... 1-2 System Components ........................................... 2 Technical Assistance ........................................ 2 Before You Begin ............................................ 2 Precautions ............................................... 2-3 Making Connections ........................................ 3-4 Locating & Making Connections ..........
PAGE 2
SYSTEM FEATURES 2 Long Range Four-Button Remotes Hand-held, easy to use and lets you operate the system from an extended distance. Keyless Entry with onboard relays Two onboard relays are provided to work any vehicle’s door locks without additional parts. This feature will remotely lock or unlock your power door locks even if the engine is running or the alarm is in valet mode. Trunk Release Remotely opens your trunk with a single push of a button.
PAGE 3
Ignition Detection Adds protection by sounding the siren and flashing the lights if the ignition wire is hotwired or turned on when the system is armed, even if the current sensor or door switch wires have been cut. Computer Controlled Fan Sensor Override No additional wiring needed. This model distinguishes between an electric fan turning on and a light bulb. Code Learning Allows your alarm to learn new remotes, should you want to add remotes, or if remotes are lost.
PAGE 4
airbag. Doing so may cause a warning light to be displayed which may require a trip to the dealer to be corrected. DO NOT leave the interior or exterior lights on for an extended period of time as it may cause battery drain. Remove the dome light fuse from the vehicle’s fuse box. NOTE: Alarm systems do not work well with a partially discharged battery. NOTE: A volt meter must be used when testing. DO NOT USE A TEST LIGHT unless it is computer-friendly.
PAGE 5
CAUTION: All wires must be wrapped with tape and wire tied. MAKING END TO END CONNECTIONS Use this method ONLY when connecting two separate wires end to end. 1. When tying two separate wires together at their ends, strip back one inch of insulation on both wires and separate the strands of wire as shown below. 2. Twist upper wires together, twist lower wires together as shown. 3. Lay upper twisted pair of wires over right wire as shown. Bring lower twisted pair of wires up to meet the left wire as shown.
PAGE 6
4.Connect the siren's BLACK wire to the third mounting screw, using the spade connector. Make sure this is a solid ground. 5.Connect the siren's RED wire to the module's GREY wire. FINDING CONSTANT AND IGNITION POWER Your system requires 12 volts constant and ignition 12 volt that is only on when the ignition is on. 1.There is usually a large gauge wire going to your ignition switch. Probe this wire. Confirm that the light comes on or the meter indicates 12 volts.
PAGE 7
INSTALLING THE FLASHING LED STATUS INDICATOR The LED indicator installs inside your vehicle and should be installed as high as possible and be visible from all windows. Drill a 1/4" mounting hole in the dash panel or use the supplied mounting bracket. BLUE PLUG WHITE PLUG ON THE LEFT OF MODULE : : CONNECTING THE LED STATUS INDICATOR Insert the blue plug of the LED status indicator into the blue plug next to the main connector. TEST: Press transmitter Button #1, the LED should flash.
PAGE 8
OPTIONAL CONNECTIONS TESTING: Door Locks There are three basic types: “Type A” Door Lock Test (Most GMs and some Chryslers) Probe both of your door lock wires going to the door lock switch usually located in the driver’s kick panel. Probe the lock and the unlock wires, the test probe will show a (-) negative and the GREEN light will glow bright on both the lock and the unlock wires. Press and hold the lock button on the switch and test the lock wire.
PAGE 9
HOW TO USE YOUR REMOTE TRANSMITTER WIRING DIAGRAMS FIGURE 1 5-Pin Door Lock Harness Connector 1. Red (+) 12 Volt Constant 2. Black Chassis Ground 3. Grey (+) Siren Output 4. White/Red Button #3 / Channel #3 (-) Output: Window Rollup, etc. 200 mA Max 5. White/Yellow Button #2 / Channel #2 (-) Output: Remote Starter, etc. 200 mA Max 6. Brown/Black Not Used 7. Green/Black Not Used 8. Orange (-) Output when armed: Starter Disable 9.
PAGE 10
OPERATING INSTRUCTIONS LED Status Indicator The LED (red light) provides valuable information about the system and is also a theft deterrent.
PAGE 11
Lock/Unlock with Ignition On Disarm the system and press and hold Button #3 for (10) ten seconds or until the unit chirps once. Release Button #3 then press and release Button #2 within (2) two seconds. The unit will chirp once indicating that the unit is programmed to Lock/Unlock the doors with Ignition. NOTE: Factory setting is Lock/Unlock with Ignition Off. NOTE: When this feature is programmed, the system will Lock the doors (5) five seconds after the ignition key is turned on.