User's Manual

ManualsBrandsBulldog Security ManualsGarage Door OpenerBulldog Security Remote Starter RS82

CONTENTS

REMOTE STARTER MODEL RS82

INSTALLATION GUIDE

•

OWNER’S GUIDE

Technical Assistance

All tech personnel are expertly qualified to answer any technical questions.

Technicians are available Monday through Friday from 9:00 a.m. until 8:00 p.m. and Saturday 10:00 a.m. until 4:00 p.m.

Address

288 Canton Avenue • Wintersville, Ohio 43953

Telephone

Phone: 740-264-4710 • 800-878-8007 • Fax: 740-264-7306

System Features ....................................... 1

System Components ..................................... 1

Required Tools ........................................ 1

Technical Assistance .................................. 1

Before You Begin .................................... 1-2

Precautions........................................... 2

Making Wiring Connections............................ 2-4

Locating & Making Connections........................ 4-5

Connecting the 11-Pin Harness and the 4-Relay Harness...6

Neutral Safety Switch ................................. 6

Factory Anti-Theft System.............................. 7

How to use Your Remote Transmitter ..................... 7

Programming Instructions .............................. 7

Summary of content (8 pages)

PAGE 1
INSTALLATION GUIDE • OWNER’S GUIDE REMOTE STARTER MODEL RS82 CONTENTS System Features ....................................... 1 System Components ..................................... 1 Required Tools ........................................ 1 Technical Assistance .................................. 1 Before You Begin .................................... 1-2 Precautions ........................................... 2 Making Wiring Connections............................
PAGE 2
SYSTEM FEATURES Two-Button Extended Range Remote Control Remotely start your car to run the heater or air conditioning from an extended distance. Parking Light Confirmation signal and will remain on if the engine is remotely Confirms that your vehicle has received a remote signal and will remain on if the engine is remotely started. (Optional part #775 required.) Code Learning Allows your remote starter to learn new remotes, should you want to add remotes, or if remotes are lost.
PAGE 3
Since there are many different makes and models of vehicles, look at the wiring chart on or our website, www.bulldogsecurity.com/wires.htm. Read this manual thoroughly before starting the installation. You must decide if the parking light option is desired. An optional part #775 will be needed. Please do not skip any steps. TACH/TACHLESS OPERATION In most cases the decision to go with tachless mode will save time during the installation. If your vehicle is hard-starting then you should use tach mode.
PAGE 4
. Insert the wire from the unit through the hole as shown. 5. Wrap the wire around one side then the other and finally around itself as shown. 1 2 3 6. Use electrical tape to wrap. Be sure to cover the wire about two inches on either side of the connection. First pull the wire that you have just connected along side the wire you connected to, tape and wire tie them together. Use this method for all connections. Wire Tie Electrical Tape CAUTION: All wires must be wrapped and taped.
PAGE 5
4. Use electrical tape to wrap, be sure to cover about 2 inches on either side of connection. Secure with wire ties as shown. Electrical Tape Wire Tie Wire Tie Use this method ONLY when connecting two separate wires end to end. LOCATING & MAKING CONNECTIONS Please see the wiring chart on our website, www.bulldogsecurity.com.
PAGE 6
CHASSIS GROUND Factory Bolt Locate an easy to get to bolt or screw located under the driver’s side of the dash and attach the BLACK ground wire from the 11-pin Spade Connector harness securely as pictured. Parking Light Output (-) (Optional part #775 required) Turn the parking lights to the ON position. (NOT YOUR HEADLAMPS). Probe the wire(s) coming from your headlamp switch. Find the wire that will show +12V only when the parking lights are ON and ground when the lights are OFF.
PAGE 7
CONNECTING THE 11-PIN HARNESS & 4-RELAY HARNESS RED To +12V constant BLACK Ground BROWN (-) Parking Light Output 250ma (Requires optional part #775) BLUE/BLACK (+) Brake Switch YELLOW/BLACK Ignition Input BLUE (-) Aux. Alarm Channel Input BLACK/BLUE (-) To Hood Pin Switch BLACK/WHITE Tach to (-) Neg.
PAGE 8
FACTORY ANTI-THEFT SYSTEMS FOR GENERAL MOTORS CARS ONLY System 1: PASSKEY I and II system (1985 and up). This system has a resistor pill in the key. Measure resistance of the pill using a volt/ohm meter. A bypass module is available, part #VATS-WR module. System 2: PASSLOCK I and II system (1995 and up). Passlock does not have a pill in the key. It has a light on the dash that states ANTITHEFT OR SECURITY system. A bypass module is available, part #GMBP-721 module.