Installation guide

ManualsBrandsBulldog Security ManualsAutomotiveRS1300E

CONTENTS

ALARM AND REMOTE CONTROL STARTER

MODEL RS1300E

INSTALLATION GUIDE

•

OWNER’S GUIDE

Technical Assistance

All tech personnel are expertly qualified to answer any technical questions.

Technicians are available Monday through Friday from 9:00 a.m. until 8:00 p.m. and Saturday 10:00 a.m. until 4:00 p.m.

Address

288 Canton Avenue • Wintersville, Ohio 43953

Telephone

Phone: 740-264-4710 • 800-878-8007 • Fax: 740-264-7306

System Features ...................................... 1

System Components .................................... 1

Required Tools ....................................... 1

Technical Assistance.................................. 2

Before You Begin...................................... 2

Precautions .......................................... 2

Using your Test Probe................................. 3

Making Connections.................................. 3-4

Locating & Making Connections ....................... 4-6

Neutral Safety Switch............................... 6-7

Connecting Wiring Harness............................. 7

Antenna Placement .................................... 7

Optional Connections................................ 7-9

OOperator Programming Instructions .................. 9-10

How to use Your Remote Transmitter .................... 10

Summary of content (12 pages)

PAGE 1
INSTALLATION GUIDE • OWNER’S GUIDE ALARM AND REMOTE CONTROL STARTER MODEL RS1300E CONTENTS System Features ...................................... 1 System Components .................................... 1 Required Tools ....................................... 1 Technical Assistance .................................. 2 Before You Begin...................................... 2 Precautions .......................................... 2 Using your Test Probe .................................
PAGE 2
SYSTEM FEATURES 2 Four-Button Extended Range Remote Controls Remotely start your car to run the heater, air conditioning or defroster from an extended distance. Keyless Entry Remotely locks and unlocks your power door locks. Built In Alarm Features Provides door, hood and impact protection. Horn and Siren Output Lets you choose between the vehicle’s factory horn or an optional six tone siren.
PAGE 3
TECHNICAL ASSISTANCE Should you need help. First check our website at www.bulldogsecurity.com or call our toll-free Tech Support Hotline Monday through Friday 9AM-8PM and Saturday 10AM-4PM EST at 800-878-8007. You must give the following information: •Name •Telephone Number with Area Code (Fax number if applicable) •Year, Make, and Model of the vehicle •The model you are installing •The type of assistance you are requesting If you give the above information you will be called back as soon as possible.
PAGE 4
USING YOUR TEST PROBE To operate your test probe, connect the black clip to a good chassis ground. Connect the red clip to a good 12V positive source. If the test probe is connected correctly, both the green and the red lights will be dimly illuminated. If a positive source is probed, the red light will glow bright and the green light will go out. If a negative source is probed, the green light will glow bright and the red light will go out.
PAGE 5
2. Twist upper wires together, twist lower wires together as shown. 3. Lay upper twisted pair of wires over right wire as shown. Bring lower twisted pair of wires up to meet the left wire as shown. 4. Use electrical tape to wrap, be sure to cover about 2 inches on either side of connection. Secure with wire ties as shown. Electrical Tape Wire Tie Wire Tie Use this method ONLY when connecting two separate wires end to end. LOCATING & MAKING CONNECTIONS Please see the wiring chart on this website.
PAGE 6
1. If your vehicle has only one (1) ignition wire, as most 1993 and older domestic and import vehicles do, connect the heavy gauge WHITE wire to it. 2. If your vehicle has two (2) ignition wires, as most 1994 and newer vehicles do, connect the heavy gauge RED with WHITE stripe wire to the Ignition 2 wire. 3. If your vehicle has three (3) ignition wires, as some newer GMs, Fords and Chryslers do, connect the heavy gauge WHITE wire to the third ignition along with the Ignition 1 wire.
PAGE 7
PARKING LIGHTS (+12V only with parking lights on) Turn the parking lights to the ON position. (NOT YOUR HEADLAMPS). Probe the wire(s) coming from your headlamp control switch. The correct wire will show +12V and the RED light will glow bright only when the parking lights are ON. Connect the BROWN wire from the 16-pin harness to this wire. If this wire tests as a (-) negative, the GREEN light glows bright. See negative parking light diagram. NEGATIVE PARKING LIGHT DIAGRAM ONLY Optional part #775 required.
PAGE 8
PRE-1996 GM REAR WHEEL DRIVES WITH PURPLE CRANK WIRE Optional part #775 required. YELLOW PRE-1996 DODGE DAKOTAS Optional part #775 required. Driver’s Door Switch WHITE TAN Ground Key Cylinder Tie into heavy white wire on 4-relay harness FUSE 86 85 Ground Ground Key Cylinder Tie into heavy white wire on 4-relay harness 30 BLUE GREEN BLACK 87a 5 Amp fuse WHITE BLACK/LT.BLUE 87 RED Not Used FUSE 86 87 85 87a 5 Amp fuse LT.
PAGE 9
light will glow bright on both the lock and the unlock wires. Press and hold the lock button on the switch and test the lock wire. The correct wire will test (+) positive and the RED light will glow bright. Release the lock button and this wire should show a (-) negative and the GREEN light will glow bright. Now press and hold the unlock button on the switch and test the unlock wire. The correct wire will test (+) positive and the RED light will glow bright.
PAGE 10
DOME LIGHT To determine if your dome light is turned on with (+) positive or (-) negative trigger, probe for a wire in the driver’s side kick panel that switches polarity when the door is closed, then opened. You can also find this wire going to the under dash courtesy lights. •If this wire tests (+) positive, the RED light glows bright when the door is open (as with most Fords) and when the door is closed, this wire tests as a (-) negative, the GREEN light glows bright, this is (+) positive dome light.
PAGE 11
Automatic Start - On Press and hold brake. Press and hold Button #2 until the parking lights flash twice. Release. Press and release Button #1. The parking lights will flash once. The automatic start is programmed ON. Release the brake, the parking lights will flash three (3) times. NOTE: Factory setting is OFF. Automatic Start - Off Press and hold brake. Press and hold Button #2 until the parking lights flash twice. Release. Press and release Button #1. The parking lights will flash twice.
PAGE 12
Clearing the Memory of the Unit Press and hold the brake pedal, now cycle the key in the ignition switch from OFF to RUN (not start) five (5) times within four (4) seconds. Release the brake and try the remote. The unit should not function with the remote. If the unit does not function, unplug the unit from both harnesses, wait one (1) minute and plug it back in. Press Button #4 (stop) the parking lights will flash three (3) times, the unit is now back to factory default and ready to operate.