USER GUIDE Read Before Use! SST220 “Make the Cut!” SST226 Do not use on High Pressure Laminate or Solid Wood www.BulletTools.com • 208-772-0175 PRT-INS-0220 RevB.05.
WARNING: FAILURE TO FOLLOW THIS GUIDE MAY RESULT IN SERIOUS INJURY! USING THIS MACHINE WITH RESPECT AND CAUTION WILL CONSIDERABLY REDUCE THE RISK OF PERSONAL INJURY. SAFETY GUIDE FOR THE EZ SHEAR™ SST Series 1 �����READ AND UNDERSTAND THIS INSTRUCTION MANUAL BEFORE OPERATING THE EZ SHEAR™. 2 �����If you are not thoroughly familiar with the operation of the EZ Shear™, obtain advice from a qualified instructor or call 800-406-8998 (Intl.: 208-772-0175). 3 �����Stay alert.
You will need #2 & #3 Phillips head screwdrivers and a 1/2” (13mm) socket or wrench. SST220 Set up Please Review and Verify Parts Included in Box: 2. F. 1. Power Assembly 1a. Safety Lock pin 2. Handle Assembly 3. Fence 4. Table 5. Tail 6. Rails (2) 7. Hone Stone 8. Mounting Bracket (4) 9. HARDWARE KIT D. E. 1. 3. A. B. 4. 7. 8. Item A. Item B. Item C. Item D. Item E. Item F. D. E. F.
Assembly 1. Attach Rails Attach rails and mounting bracket to Power Assembly base using Item A machine screws, fitted with Item B star washers. 2. Attach Tail Attach tail and mounting bracket to rails using Item C machine screws. Make sure holes in tail are facing up. 1 3. Attach Table 2 3 3B A. Attach table to base starting with front, start screws with hand, use Item D screws. 3A B. Attach back of table to tail using Item E self tapping screws. Tighten with #2 Phillips. 4.
. Place the Fence 220 For 220: Your EZ Shear is equipped with an aluminum fence which may be set to common roof pitches. (4/12, 6/12, 8/12, and 12/12) Simply align with desired position and press pins into place. Note: The fence is friction fit (requires effort to insert or remove). For 226: Slide fixed clamp into the front quick alignment notch. For 90° cuts, slide loose clamp into rear alignment notch and tighten star knob.
The 226 Shear has two Leverage Modes Mode 1: Use the long-stroke cams (black lobes) only for lightweight products thicker than 1/2 inch. Mode 2: For all other recommended products, use the short-stroke cams (grey lobes). Leverage Switch Instructions Engaging the Short-Stroke Cams 1) Remove any obstructions from under the blade. 2) Push handle to the closed position. 3) Ensure that the camlock pin is disengaged.
Your EZ Shear cuts a wide variety of products. Please refer to this cut guide for recommended products and thicknesses. SST CUT GUIDE MAINTENANCE Honing the Blade Maximum Thickness = 25mm or 1” Material Siding, Fiber Cement Board Siding, Pressboard Lap Siding, Vinyl Siding, Wood Trim, OSB Trim, Fiber Cement Trim, Vinyl Hone every 100 cuts Push the handle down until blade is 1/4” (6mm) open. Lay the hone stone against the flat face of the blade (side toward the table).
WARRANTY 30 Day Satisfaction Guarantee Bullet Tools™ is confident that you will be absolutely pleased with the purchase of our product. If, for any reason, you are not completely satisfied with your tool, we will refund your purchase price at any time within 30 days of your original purchase (receipt required). If you want to return your product under our 30-day no risk trial offer (valid only for purchases made in the US), please contact us at 1-800-406-8998 or 208-772-0175 for return instructions.
