USER GUIDE Read Before Use! 909 913 920 Applies to Model Numbers: 909, 913 & 920 www.BulletTools.com • 208-772-0175 PRT-INS-9000Rev.B.4.
! WARNING Very Sharp Blade Warning: Failure to Follow These Rules May Result in Serious Injury! Using This Machine With Respect And Caution Will Considerably Reduce The Risk Of Personal Injury. Safety Rules for the Magnum™ FLOORING Shear 1. Read and understand this instruction manual before operating the MAGNUM™ Flooring Shear. 2. If you are not thoroughly familiar with the operation of the MAGNUM™ Flooring Shear, obtain advice from a qualified instructor or call 800-406-8998. 3. Stay alert.
IN THE BOX You will need #2 & #3 Phillips head screwdrivers Please Review and Verify Parts Included: 1. 2. 3. 4. 5. 6. 7. 8. Power Assembly Handle Assembly Fence Table Tail Rails (2) Hone Stone Hardware Kit D 2 1 E C 3 F A 4 7 5 B 6 Hardware kit*: Item A. Item B. Item C. Item D. Item E. Item F. Item G.
Set Up 3 3. Attach Table A. Attach table to base starting with front, start screws with hand, using Item D machine screws. 3A 3B B. Attach back of table to tail using Item E self tapping screws. Cam Shaft M16 x 50 Bolt 4 Back Stroke Stop dl e y Hansembl As 4. Attach Handle: Insert handle into cam shaft. Note: Backstroke Stop must be on top! Tighten Item F Bolt (pre-installed in cam shaft) with 10mm hex wrench Item G (Included).
Making Cuts The MAGNUM™ Flooring Shear is operated manually. The two-part extendable handle is grasped by the operator and pushed down to make a cut. ! USE EXTREME CAUTION! Blade is very sharp. Cutting 1. Unlock safety lock by sliding knob over and down. 2. Insert material. It is recommended that you HOLD MATERIAL IN PLACE until the cut is complete. ! Always keep hands away from blade. 3. PUSH HANDLE DOWN TO CUT. Some effort may be required depending on hardness of material. 4.
Custom Settings Factory Setting Set to cut over 3/4" or 19mm Backstroke Stop To cut approved products over 3/4" / 19mm thick, loosen Phillips head screw on the Backstroke Stop; turn the Backstroke Stop 180º and tighten screw. For more convenience when cutting thinner products, restore factory setting.
Maintenance WHEN TO HONE To Hone There are three situations when it is very important to hone the blade (remove burrs) on the flat side of the blade. With the blade in the machine, it is quick and easy to hone; Simply pull the handle down until the blade is just above the blade stop (approximately 1/8"). Then, lay the wide flat side of the hone stone against the flat side of the blade and move hone stone from end to end 2 to 3 times to remove any burrs. 1. After the first 30-100 cuts on a new blade 2.
Maintenance Changing the Blade ! 1 2 Warning Blade is extremely sharp! Use hand protection when removing, honing, or sharpening blade! Jack Screws 1. Turn Shear upside down Tip: put the shear on the edge of a sturdy table. 2. Loosen Blade Using a Phillips screwdriver, remove the Item D screws. 3. Remove Blade 3 Hold blade by each end and carefully lift out of pocket. 4.
Available Accessories 1 Replacement Blades 1 9" MAGNUM Flooring Blade 13" MAGNUM™ Flooring Blade 20" MAGNUM™ Flooring Blade #909B #913B #920B ™ 2 2 Hone Stone #701S Shear Stand #709 Keep your blade honed for longer use! 3 3 Provides a sturdy, raised platform for use or display. Mounting brackets sold separately (#900MB). 4 All Angle Fence #701AF Sets to any angle from 0 to 90 degrees. 4 5 Slickshot #701SL Dry lubricant for the MAGNUM Flooring Shear.
Material d Pecan n Rosewoo a i v i l Bo rry n Che Africa Bamboo ) (some Walnut n a c i r Af lle Sappe n Maple a i l i z Bra Maple Hard ahogany M t Royal ean Walnu s b s b e i r r Ca Cyp alian r t s u A Oak White e Oak g Vinta sh A e t i h ech W an Be Oak c i r e d Am e ern R North Birch Pine w Yello ean Heart b Carib ine P t r a e H h Larc tus Teak n Eucalyp a i l Brazi n Walnut ia Peruv alnut W k c a l B herry ine ican C Amer rn Yellow P e South cewood a L ny . A .
WARRANTY 30 Day Satisfaction Guarantee Bullet Tools™ is confident that you will be absolutely pleased with the purchase of our product. If, for any reason, you are not completely satisfied with your tool, we will refund your purchase price at any time within 30 days of your original purchase (receipt required). If you want to return your product under our 30-day no risk trial offer (valid only for purchases made in the US), please contact us at 1-800-4068998 or 208-772-0175 for return instructions.
