Owner`s manual
25
• Standard Mode (Std): maintains the desired temperature of
the spa. Std will appear on the display momentarily when
you switch into Standard mode.
• Economy Mode (Ecn): heats the spa to the set temperature
only during lter cycles. Ecn will appear solid in the display
when the spa is heating and will ash intermittently when
the spa is not heating. Press jets 1 while in Economy mode
to place the spa in Standard-In-Economy mode (SE), which
operates the same as Standard mode, however; it will revert
to Economy mode automatically after 1 hour.
• Sleep Mode (SLP): heats the spa to within 20
◦
F (11
◦
C) of the
set temperature only during lter cycles. SLP will appear on
the display until the mode is changed.
Standby Mode (Sby)
Standby Mode idles all of the spa’s functions. This is helpful
when changing a lter or a JetPak. Press temp then jets 2 or
aux to start mode. Press any button to exit this mode.
Jets 1
Press jets 1 to turn pump 1 on and off and to shift between
low and high speeds. If left running, the low speed will turn off
after 4 hours and the high speed will turn off after 30 minutes.
When the low speed turns on automatically, it cannot be
turned off from the control panel.
NOTE: When in standard mode, the low speed of pump 1 may
activate for at least 2 minutes every 30 minutes to detect the
spa temperature and will heat to set temperature (if
needed).
Jets 2 (optional)
With a two pump system, press jets 2 to turn pump 2 on or off
and to shift between low and high speeds. If left running, the
pump will turn off automatically after 15 minutes. NOTE: If the
spa does not have two pumps, the jets 2 button will be
labeled aux.
Auxiliary Jet(s) Control
An optional auxiliary control pad(s)
on the side of the spa can also
activate the pump(s). NOTE: This
option is not available on Tadpole
Hot Tub models.
Light
Press light to toggle the light on and off.
The light will turn off automatically after 4 hours.
LED Light (optional)
Press light to toggle the LED light on and off. Press light + light
to shift through the color options. The light will turn off
automatically after 4 hours.
Preset Filter Cycles
The pump and ozone purier* will run during ltration. At the
start of each lter cycle, pump 2 will run for 5 minutes to clean
out the JetPaks
™
and JetPods
™
associated with pump 2.
There are two lter cycles per day. The rst lter cycle begins 6
minutes after the spa is powered up. The second lter cycle
begins 12 hours later. Filter duration is programmable for 1-12
hours (F1-F12). The default lter time is 2 hours per cycle.
To program, press temp + jets 1. Press temp to select the lter
duration. Press jets 1 to select the number of lter cycles. The
display will show dn (day and night), d (day only), or n (night
only). Press temp to adjust. Press jets 1 to exit the program. For
continuous ltration, use F12 and dn. NOTE: Allowing the lter
pump to operate for extended periods of time with the cover
on the spa will result in a rise of the spa water temperature.
During warmer months of the year, it is advisable to set the
duration of the ltration cycle to the minimum level needed
to keep the water clean.
Freeze Protection
If the temperature drops to 44
◦
F (7
◦
C) within the heater, the
pump automatically activates to provide freeze protection.
The pump will stay on 4 minutes after the sensor has detected
the temperature has reached 45
◦
F (7
◦
C) or higher.
Cleanup Cycle (optional)
A cleanup cycle begins 30 minutes after the pump is turned
off or times out. The pump and ozone purier* will run for 1
hour. NOTE: To activate this feature, contact your authorized
Bullfrog Spa dealer.
*Ozone Purier (optional)
The ozone purier runs during lter cycles (except when pump
1 is operating on high speed or when pump 2 is running on
any speed) and during clean-up cycles.
Operation