Owner`s manual

27
Operation
Temp Set: 80
◦
F-104
◦
F (26
◦
C-40
◦
C)
The startup temperature is set to 100
◦
F (38
◦
C). The last
measured temperature is constantly displayed on the LCD.
NOTE: The spa temperature displayed is only current when
the pump has been running for at least 2 minutes.
Press warmer or cooler once to display the set temperature.
Press warmer or cooler again to increase or decrease the
temperature. After three seconds, the LCD will automatically
display the last measured spa temperature.
Spa Operating Modes
A multi-button sequence is used to switch between Standard,
Economy, and Sleep modes. Press mode/prog to enter mode,
press cooler to cycle through modes, press mode/prog to
conrm selection.
• Standard Mode (Std): maintains the desired temperature.
The Standard icon will display.
• Economy Mode (Ecn): heats the spa to the set temperature
only during lter cycles. Press jets 1 while in Economy mode
to put the spa in Standard-In-Economy mode (SE), which
operates the same as Standard mode, however, it will revert
to Economy mode automatically after 1 hour. The Economy
icon will display.
• Sleep Mode (SLP): heats the spa to within 20
◦
F (11
◦
C) of the
set temperature during lter cycles only. The Sleep icon
will display.
Standby Mode (Sby)
Standby Mode idles all of the spa’s functions. This is helpful
when changing a lter or a JetPak. Press temp then jets 2 or
aux to start mode. Press any button to exit this mode.
Jets 1
Press jets 1 to turn pump 1 on and off and to shift between
low and high speeds. The low speed will turn off after 4 hours
and the high speed will turn off after 30 minutes. When the
low speed turns on automatically, it cannot be turned off
from the control panel. NOTE: When in standard mode, the
low speed of pump 1 may activate for at least 2 minutes
every 30 minutes to detect the spa temperature and will
heat to set temperature if needed.
Jets 2 (optional)
Press jets 2 once to turn pump 2 on and off and to shift
between low and high speeds. If left running, the pump will
turn off after 30 minutes. NOTE: If the spa does not have two
pumps, the jets 2 button will be labeled aux.
Auxiliary Jet(s) Control
An optional auxiliary control pad(s) on the side of the spa
can also activate the pump(s).
Option
This button does nothing by itself; however, it is used as part of
the Invert sequence described as follows.
Invert Display
Press warmer or cooler + option to change the direction of
the information on the display.
Light
Press light to toggle the light on and off. The light will turn off
automatically after 4 hours.
LED Light (optional)
Press light to toggle the light on and off. Press light + light to
shift through color options. The light will turn off automatically
after 4 hours.
Freeze Protection
If the temperature drops to 44
◦
F (7
◦
C) within the heater, the
pump automatically activates to provide freeze protection.
The pump will stay on 4 minutes after the sensor has detected
the temperature has reached 45
◦
F (7
◦
C) or higher.
Cleanup Cycle (optional)
A cleanup cycle begins 30 minutes after the pump is turned
off or times out. The pump and ozone purier* will run for 1
hour. NOTE: To activate this feature, contact your authorized
Bullfrog Spa dealer.
Locking the Panel
Press time + jets 1 + warmer within 3 seconds. When locked,
the Panel Lock (PL) indicator light will light. All buttons will be
frozen except the time button. To unlock the panel, press time
+ jets 1 + cooler.
Locking the Set Temperature
Press warmer or cooler + time + jets 1 + warmer within 3
seconds to activate the lock. The TL indicator light will light
when the set temperature is locked. To unlock the set
temperature, press warmer or cooler + time + jets 1 + cooler.
*Ozone Purier (optional)
The ozone purier runs during lter cycles (except when pump
1 is operating on high speed or when pump 2 is running on
any speed) and during clean-up cycles.