Troubleshooting guide

16
NOTE: Your spa’s factory default lter cycle start times are 8:00am and
6:00pm daily. When using the most economical “rest” mode, it is recom-
mended that you adjust the ltration cycles to run just prior to the time of
your usual spa use.
Filter Cycle 1
Using the same navigation and adjustment as Setting the Time, Filter Cycles
are set using a start time and a duration. Each setting can be adjusted in
15-minute increments. e panel calculates the end time and displays it
automatically.
Filter Cycle 2
Simply navigate to the Filter Cycle 2 line by pressing the Right Navigation
Button, and when “Yes” is highlighted, press Up or Down to toggle Filter
Cycle 2 on and o. When Filter Cycle 2 is ON, it can be adjusted in the
same manner as Filter Cycle 1 by navigating to the right. It is possible to
overlap Filter Cycle 1 and Filter Cycle 2, which will shorten overall ltration
by the overlap amount.
Adjusting Filtration
Purge Cycles
In order to maintain sanitary conditions, as well as protect against freezing,
secondary water devices will purge water from their respective plumbing by
running briey at the beginning of each lter cycle. If the Filter Cycle 1
duration is set for 24 hours, enabling Filter Cycle 2 will initiate a purge when
Filter Cycle 2 is programmed to begin.
Adjusting Filtration
Filter Cycle 1
Using the same navigation and adjustment as Setting the Time, Filter Cycles are set using a start time and a duration. Each
setting can be adjusted in 15-minute increments. The panel calculates the end time and displays it automatically.
Filter Cycle 2
Simply navigate to the Filter Cycle 2 line by pressing the Right Navigation Button, and when “Yes” is highlighted, press
Up or Down to toggle Filter Cycle 2 on and off. When Filter Cycle 2 is ON, it can be adjusted in the same manner as Filter
Cycle 1 by navigating to the right.
It is possible to overlap Filter Cycle 1 and Filter Cycle 2, which will shorten overall fi ltration by the overlap amount.
Purge Cycles
In order to maintain sanitary conditions, as well as protect against freezing, secondary water devices will purge water from
their respective plumbing by running briefl y at the beginning of each fi lter cycle.
If the Filter Cycle 1 duration is set for 24 hours, enabling Filter Cycle 2 will initiate a purge when Filter Cycle 2 is pro-
grammed to begin.
Filter Cycles
Back
Filter Cycle 1
Starts at 12:00 AM
Runs 0 HR 0 Min
Ends at 12:00 AM
Filter Cycle 2 NO
Starts at 12:00 AM
Runs 0 HR 0 Min
Ends at 12:00 AM
Filter Cycles
Back
Filter Cycle 1
Starts at 6:15 AM
Runs 3 HR 0 Min
Ends at 9:15 AM
Filter Cycle 2 NO
Starts at 12:00 AM
Runs 0 HR 0 Min
Ends at 12:00 AM
Cancel
Save
Invert Panel
Selecting Invert Panel will fl ip the display and the buttons so the panel can be easily operated from inside or outside the
hot tub.
Restricting Operation
e control can be restricted to prevent unwanted use or temperature adjust-
ments. Locking the Panel prevents the controller from being used, but all au-
tomatic functions are still active. Locking the Settings allows Jets and other
features to be used, but the Set Temperature and other programmed settings
cannot be adjusted.
Restricting Operation
Unlocking
An Unlock Sequence using the navigation buttons can be used from the Lock Screen. The Unlock Sequence is the same for
both Panel Lock and Settings Lock.
The control can be restricted to prevent unwanted use or temperature adjustments.
Locking the Panel prevents the controller from being used, but all automatic functions are still active.
Locking the Settings allows Jets and other features to be used, but the Set Temperature and other programmed settings
cannot be adjusted.
Lock
Back
Settings
Panel
OFF
OFF
Lock
Back
Settings
Panel
OFF
ON
Set: 104°F
8:32 PM
Ozone
Filter 1
Unlock
High Range
102°F
Ready in Rest Mode
Heating