Troubleshooting guide

17
Unlocking
An Unlock Sequence using the navigation buttons can be used from the
Lock Screen. e Unlock Sequence is the same for both Panel Lock and Set-
tings Lock. You must enter and highlight “Unlock” then enter and highlight
panel “ON” before entering the unlock sequence.
Restricting Operation
Unlocking
An Unlock Sequence using the navigation buttons can be used from the Lock Screen. The Unlock Sequence is the same for
both Panel Lock and Settings Lock.
The control can be restricted to prevent unwanted use or temperature adjustments.
Locking the Panel prevents the controller from being used, but all automatic functions are still active.
Locking the Settings allows Jets and other features to be used, but the Set Temperature and other programmed settings
cannot be adjusted.
Lock
Back
Settings
Panel
OFF
OFF
Lock
Back
Settings
Panel
OFF
ON
Set: 104°F
8:32 PM
Ozone
Filter 1
Unlock
High Range
102°F
Ready in Rest Mode
Heating
Restricting Operation
Unlocking
An Unlock Sequence using the navigation buttons can be used from the Lock Screen. The Unlock Sequence is the same for
both Panel Lock and Settings Lock.
The control can be restricted to prevent unwanted use or temperature adjustments.
Locking the Panel prevents the controller from being used, but all automatic functions are still active.
Locking the Settings allows Jets and other features to be used, but the Set Temperature and other programmed settings
cannot be adjusted.
Lock
Back
Settings
Panel
OFF
OFF
Lock
Back
Settings
Panel
OFF
ON
Set: 104°F
8:32 PM
Ozone
Filter 1
Unlock
High Range
102°F
Ready in Rest Mode
Heating
Hold Mode
Hold Mode is used to disable the pumps during JetPak removal and service
functions like cleaning or replacing the lter. Hold Mode will last for 1 hour
unless the mode is exited manually. If spa service will require more than an
hour, it may be best to simply shut down power to the spa.
Additional Settings
Utilities
e Utilities Menu contains the following:
A/B Temps
When this is set to On, the temperature display will alternate to display
temperature from Sensor A and Sensor B in the heater.
Fault Log
e Fault Log is a record of the last
24 faults that can be reviewed by a
service tech.
GFCI Test
is screen allows the GFCI to be
tested manually from the panel and
can be used to reset the automatic
test feature. If the GFCI Test Feature
is reset, the device will trip within 7
days. (See page 31)
Additional Settings
Hold Mode
Hold Mode is used to disable the pumps during service functions like cleaning or replacing the fi lter. Hold Mode will last
for 1 hour unless the mode is exited manually. If spa service will require more than an hour, it may be best to simply shut
down power to the spa.
Utilities
The Utilities Menu contains the following:
A/B Temps
When this is set to On, the temperature display will alternate to display temperature from Sensor A and Sensor B in
the heater.
Fault Log
The Fault Log is a record of the last 24 faults that can be
reviewed by a service tech.
GFCI Test
This screen allows the GFCI to be tested manually from the panel
and can be used to reset the automatic test feature. If the GFCI
Test Feature is reset, the device will trip within 7 days. (See
Page 16)
Fault Log
Back
Entry 2
Message Code M026
1 Days Ago 2:21PM
Rest Mode
High Range
Set Temp 104°F
Sensors: A: 100 B: 96
Message:
Sensors are out of sync
Preferences
e Preferences Menu allows the user
to change certain parameters based on
personal preference.
Temp Display
Change the temperature between
Fahrenheit and Celsius.
Additional Settings
Preferences
The Preferences Menu allows the user to change certain parameters based
on personal preference.
Temp Display
Change the temperature between Fahrenheit and Celsius.
Time Display
Change the clock between 12 hr and 24 hr display.
Reminders
Turn the reminder messages (like “Clean Filter”) On or Off.
Cleanup
Cleanup Cycle Duration is not always enabled, so it may not appear. When it is available, set the length of time Pump
1 will run after each use. 0-4 hours are available.
Color
Pressing the Select Button when Color is highlighted will cycle through 5 background colors available in the control.
Language
Change the language displayed on the panel.
Preferences
Back
Temp Display
Time Display
Reminders
Cleanup
Color
Language
°F
12 HR
On
0.5 HR
`
Blue
English
`