Troubleshooting guide

27
Main Filtration
Filter cycles are set using a start time and
a duration. Start time is indicated by an
“A” (am) or “P” (pm) in the bottom right
corner of the display. Duration has no
“A” or “P” indication. Each setting can be
adjusted in 15-minute increments. e
panel calculates the end time and displays
it automatically.
Adjusting Filtration
Sets Filter 1 length in hours
Sets start hour Selects minutes
Selects part of an hour
SET
FLTR1 P
SET
FLTR1 P
SET
FLTR1 P
Sets 15-minute increments
SET
FLTR1 P
FLTR1
FLTR1 SET
FLTR1
SET
FLTR1
SET
FLTR1
Shows/ashes start time
FLTR1
to show RUN HRS
to show F1 ENDS xx:xx
Sets 15-minute increments
A
1
While the Temperature is
still ashing, press menu
repeatedly until FLTR 1
appears in the LCD.
SET
RANGE
Main Screen
READY
RANGE
FLTR1
Main Screen
READY
RANGE
FLTR1
Sets Filter 1 length in hours
Sets start hour Selects minutes
Selects part of an hour
SET
FLTR
2 P
SET
FLTR
2 P
SET
FLTR
2 P
Sets 15-minute increments
SET
FLTR
2 P
FLTR
2
FLTR
2
SET
FLTR
2
SET
FLTR
2
SET
FLTR
2
Shows/ashes start time
FLTR
2
to show RUN HRS
to show F1 ENDS xx:xx
Sets 15-minute increments
A
Main Screen
READY
RANGE
FLTR1
2
To next item in
Main Menu
Main Screen
READY
RANGE
FLTR1
SET
FLTR
2
SET
FLTR
2
To Set
To Set
To Set
To Set
To Set
Waiting
Several Seconds
Reverts to Original Setting
Waiting
Several Seconds
Reverts to Original Setting
Wait to
Revert
*****
Waiting
Several Seconds
Reverts to Original Setting
*****
Waiting several seconds
will lose any new Filter 1
Start Time and Run Hours and
revert to the previous Filter 1 settings.
*****
To Set
Waiting several seconds
will lose any new Filter 2 On/OFF,
Start Time and Run Hours and
revert to any previous Filter 2 settings.
*****
*****
Wait to
Revert
*****
*****
Main Filtration
Filter cycles are set using a start time and a duration. Start time is indicated by an “A” or “P” in the bottom right corner of
the display. Duration has no “A” or “P” indication. Each setting can be adjusted in 15-minute increments. The panel calcu-
lates the end time and displays it automatically.
Indicates Flashing or Changing Segment
Key
A temperature button, used for “Action”
menu or dedicated “Choose” button, depending on control panel
conguration
Indicates Alternating or Progressive Message - every 1/2 second
Waiting time that keeps the last change to a menu item.
Waiting time (depends on menu item) that reverts to original setting and
ignores any change to that menu item.
*****
Filter Cycle 2
It is possible to overlap Filter Cycle 1 and Filter Cycle 2, which will
.tnuoma palrevo eht yb noitartl if llarevo netrohs
Purge Cycles
In order to maintain sanitary conditions, secondary Pumps will purge water
if hcae fo gninnigeb eht ta y lfeirb gninnur yb gnibmulp evitcepser rieht morf
lter cycle.
If Filter Cycle 1 is set for 24 hours, enabling Filter Cycle 2 will initiate a purge
when Filter Cycle 2 is programmed to begin.
Filter Cycle 2
It is possible to overlap Filter Cycle 1 and
Filter Cycle 2, which will shorten overall
ltration by the overlap amount.
Purge Cycles
In order to maintain sanitary conditions,
secondary Pumps will purge water
from their respective plumbing by run-
ning briey at the beginning of each lter
cycle. If Filter Cycle 1 is set for 24 hours,
enabling Filter Cycle 2 will initiate a purge
when Filter Cycle 2 is programmed to
begin.
Adjusting Filtration
Main Menus
Main Screen
Menu Button
P
SET
RANGE
SET
While the Temperature is
still ashing, press Menu.
SET
RANGE
READY
RANGE
FLTR1
Main Screen
READY
RANGE
FLTR1
READYSET
1
2
Power-up Screens
Each time the System powers up, a series of numbers is displayed.
After the startup sequence of numbers, the system will enter Priming Mode (See Page 3).
Waiting 30 Seconds in the Main Menu
will allow the display to revert to the Main Screen.
Most changes are not saved unless Menu is pressed.
Refer to Key above.
If Time of Day is not set
“SET TIME” will
appear in this menu.
SET
Indicates Flashing or Changing Segment
Key
A temperature button, used for “Action”
Menu or dedicated “Choose” button, depending on control panel conguration
Indicates Alternating or Progressive Message - every 1/2 second
Waiting time that keeps the last change to a menu item.
Waiting time (depends on menu item) that reverts to original setting and
ignores any change to that menu item.
*****
Navigation
Navigating the entire menu structure is done with 3 buttons on the control panel.
Temperature buttons are indicated by a single button icon.
Warm and Cool can both be uesd to simplify navigation and
programming where a single Temperature icon is shown.
The MENU Button is also used to
choose the various menus and navigate each section. Pressing
the MENU button from the main screen (normal operation) will
enter the menus.
Typical use of the Temperature button(s) allows changing the Set
Temperature while the numbers are fl ashing in the LCD.
Pressing the MENU button while the numbers are fl ashing will also
enter the menus.
The menus can be exited with certain button
presses. Simply waiting for several seconds will also
return the panel to normal operation.
KEY