Troubleshooting guide

28
F / C (Temp Display)
Change the temperature between Fahrenheit and
Celsius.
12 / 24 (Time Display)
Change the clock between 12 hr and 24 hr
display.
RE-MIN-DERS (Reminders)
Turn the reminder messages (like “Clean Filter”)
On or O.
CLN-UP (Cleanup)
Cleanup Cycle Duration is not always enabled,
so it may not appear. When it is available, set the
length of time Pump 1 will run after each use. 0-4
hours are available.
DOL-PHIN AD-DRES - NOT OFFERED
ON BULLFROG SPA MODELS- (Dolphin II
and Dolphin III) Applies to RF Dolphin only.
When set to 0, no addressing is used. Use this set-
ting for a Dolphin Remote which is factory set for
no address by default. When set between 1 and
7, the number is the address. (See the Dolphin
manual for details.)
Preferences
Preferences
Toggle Yes and No
SET
SET
Toggle °F and °C
SET SET
Toggle 12-hour clock and 24-hour clock
SET
SET
Press Menu
To show rst item in Preferences menu
(F/C)
for 12-24
Press Menu for REMINDERS
Press Menu
Only if Cleanup
Cycle is enabled.
RF Dolphin only.
Press Menu for CLEAN UP
While the Temperature is
still ashing, press menu
repeatedly until PREF
appears in the LCD.
SET
RANGE
Main Screen
READY
RANGE
FLTR1
To next item in
Main Menu
(UTIL)
To next item in
Main Menu
(UTIL)
To view current setting and to toggle number of hours (0-4).
SET
SET
SET
To veiw current setting and to toggle address numbers for Dolphin II or Dolphin III (0-7)
SET
SET SET
to show Address Menu for Dolphin II or Dolphin III
To Set
To Set
To Set
To Set
To Set
Wait to
Revert
*****
Wait to
Revert
*****
Wait to
Revert
*****
Wait to
Revert
*****
Wait to Revert
*****
Several Seconds
OR
Wait Several Seconds to
Return to Main Screen
OR
Indicates Flashing or Changing Segment
Key
A temperature button, used for “Action”
menu or dedicated “Choose” button, depending on control panel
conguration
Indicates Alternating or Progressive Message - every 1/2 second
Waiting time that keeps the last change to a menu item.
Waiting time (depends on menu item) that reverts to original setting and
ignores any change to that menu item.
*****
Main Menus
Main Screen
Menu Button
P
SET
RANGE
SET
While the Temperature is
still ashing, press Menu.
SET
RANGE
READY
RANGE
FLTR1
Main Screen
READY
RANGE
FLTR1
READYSET
1
2
Power-up Screens
Each time the System powers up, a series of numbers is displayed.
After the startup sequence of numbers, the system will enter Priming Mode (See Page 3).
Waiting 30 Seconds in the Main Menu
will allow the display to revert to the Main Screen.
Most changes are not saved unless Menu is pressed.
Refer to Key above.
If Time of Day is not set
“SET TIME” will
appear in this menu.
SET
Indicates Flashing or Changing Segment
Key
A temperature button, used for “Action”
Menu or dedicated “Choose” button, depending on control panel conguration
Indicates Alternating or Progressive Message - every 1/2 second
Waiting time that keeps the last change to a menu item.
Waiting time (depends on menu item) that reverts to original setting and
ignores any change to that menu item.
*****
Navigation
Navigating the entire menu structure is done with 3 buttons on the control panel.
Temperature buttons are indicated by a single button icon.
Warm and Cool can both be uesd to simplify navigation and
programming where a single Temperature icon is shown.
The MENU Button is also used to
choose the various menus and navigate each section. Pressing
the MENU button from the main screen (normal operation) will
enter the menus.
Typical use of the Temperature button(s) allows changing the Set
Temperature while the numbers are fl ashing in the LCD.
Pressing the MENU button while the numbers are fl ashing will also
enter the menus.
The menus can be exited with certain button
presses. Simply waiting for several seconds will also
return the panel to normal operation.
KEY