OWNER’S MANUAL Nitrous Kit Part #47000
NITROUS KIT Introduction The Bully Dog Nitrous Kit allows you to control an electromechanical solenoid with a GT™ or WatchDog™; it automatically activates the solenoid if adjustable conditions like throttle position, rpm and/or speed are met. Table of Contents Parts...................................................................... 1-2 Physical Installation............................................... 2-4 GT/WatchDog Setup............................................. 5-6 Menu Blowout................
NITROUS KIT Parts Description Control Module The control module interprets the signals from the GT or WatchDog and controls the solenoids. Wiring Harness The wiring harness contains multiple wires and connects all of the parts of the Nitrous Kit with the vehicle and the GT or WatchDog. Master Switch A safety measure, the master switch will turn the Nitrous Kit off regardless of key position and GT or WatchDog settings. Installation 1. Locate a key-on fuse.
NITROUS KIT 3. Mount the control module (use the hook and loop fastener and/or zip ties to secure it in place). 4. IMPORTANT: Before beginning installation, disconnect your battery at the negative terminal. Failure to disconnect the battery could result in personal injury and/or damage to your vehicle. 5. Connect the wiring harness to the control module. ‣‣ Plug set A ‣‣ The connections are color coded (black to black and gray to gray). A 6. Connect the ground wire to the vehicle frame.
NITROUS KIT 8. Install the Master Switch. ‣‣ Make sure the switch is in the OFF position. The Master Switch should remain in the OFF position until the Nitrous Kit installation is complete. a. Connect the two silver wires (E & F) to the silver prongs on the switch. b. Connect the COLOR battery power wire to the gold prong on the switch. 9. Connect the Mini-USB cable to the adapter plug on the GT or WatchDog. ‣‣ Do not connect it directly to the GT or WatchDog. 10.
NITROUS KIT GT/WatchDog Setup Control the Nitrous Kit with a Bully Dog GT or WatchDog unit; configure up to five different setting combinations (stages). A stage will only activate when the vehicle reaches both the parameter range (Pyrometer temperature, speed, boost or RPM) and the throttle position that are selected for that stage. To support the Nitrous Kit, all GTs and Watchdogs must be updated to software version 1.1.4.3 or newer. See page 7 for a menu blowout. 1.
NITROUS KIT 5. Configure the requirements for solenoid activation (nitrous burn). a. Press the button to the left of the setting that you want to change. Go Back to NIT/METH Menu STAGE 1 Parameter: Speed Lower Limit: 22 Upper Limit: 90 Throttle Position: 90 b. Use the buttons on the right to change the value of the selected setting. c. Press Go Back (top left button) to save the change(s) and return to the previous screen.
NITROUS KIT Menu Blowout Main Menu Nitrous/Methane Setup Stage 1 Stage 2 Stage 3 Stage 4 Stage 5 Options are the same for all five stages. Parameter None Pyro 1 Pyro 2 Speed Boost RPM 7 Lower Limit Upper Limit Throttle Position Solenoid Setup Turn Solenoids (1-5) ON or OFF Set the desired value.
NITROUS KIT More Information Contacting Technical Support Technical support is open Monday-Friday 8 a.m. − 5 p.m., Mountain Standard Time. Reduced level services are available for emergencies after hours.
NITROUS KIT NOTES 9
NITROUS KIT NOTES 10
Doc.# 47000-99 v1 Check out more of our ADRENALIN PUMPING products! Sensor Docking Station Connect and control aftermarket sensors 10’ HDMI Cable with Mini-USB pigtail Connect both the Nitrous Kit and the Sensor Docking Station to a GT or WatchDog. Compatible with GT and WatchDog NItrous Fogger Nozzles Kit Part #: 47021 Accessories T-shirts Hoodies Hats Etc. Free Technical Support at: 1-940-783-9915 See More at: bullydog.