TCD-1/2 INSTALLATION & OPERATING MANUAL With ILLUSTRATED PARTS NOTE: LIFT THE DISPENSER USING THE HANDLES ONLY. DO NOT LIFT THE DISPENSER FROM THE BOTTOM. BUNN-O-MATIC CORPORATION POST OFFICE BOX 3227 SPRINGFIELD, ILLINOIS 62708-3227 PHONE: (217) 529-6601 FAX: (217) 529-6644 34106.
BUNN-O-MATIC COMMERCIAL PRODUCT WARRANTY Bunn-O-Matic Corp. (“BUNN”) warrants equipment manufactured by it as follows: 1) All equipment other than as specified below: 2 years parts and 1 year labor. 2) Electronic circuit and/or control boards: parts and labor for 3 years. 3) Compressors on refrigeration equipment: 5 years parts and 1 year labor.
INTRODUCTION These dispensers are designed to mix liquid tea concentrate with water to produce iced tea by the glass or pitcher. The concentrate can be stored either inside the dispenser, or outside with a hose connection to the dispenser. The dispenser must be placed on a sturdy counter or shelf. PLUMBING REQUIREMENTS This dispenser must be connected to a cold water system with operating pressure between 30 and 90 psi (138 and 620 kPa) from a 1⁄2" or larger supply line.
SET UP AND OPERATING PROCEDURES 1. Remove dispenser from the box and place on a sturdy, level counter. 2. Remove the brass cap and any packing material from the end of the water inlet fitting located on the rear of the dispenser. 3. Attach a 1/4" water line to the inlet fitting. This supply line must have at least 30 psi of pressure. 4. Using a screwdriver, turn the adjustment screw on the venturi mixer clockwise until the screw contacts the seat (DO NOT OVERTIGHTEN THIS SCREW!). 5.
DISPENSER CLEANING AND SANITIZING Daily Cleaning: 1. Turn handle on rear of dispenser to shut off the water supply. 2. Open the faucet to relieve pressure in the system. 3. Since the bag connector(s) have an internal shut off valve, it will be necessary to prop the valve open during cleaning. NOTE: Cutting off the mating connector of an empty concentrate bag works well for this. Keep this mating end for future cleanings of the system. 4. Turn on water supply to the dispenser. 5.
TCD-1 TCD-2 REPLACEMENT PARTS (TCD-1) 56 57 59 58 57 43 .375" BIB Adapter 42 Concentrate Bottle Tube 20 24 26 46 47 18 15 19 17 16 61 21 2 3 1 4 5 19 31 30 20 22 32 20 52 7 26 27 28 29 23 54 6 45 20 20 14 13 12 11 10 44 34 35 51 33 53 8 25 9 36 37 38 39 60 41 40 49 47 48 50 55 Early Models P3457.60 6 34106.
REPLACEMENT PARTS (TCD-1) ITEM PART NO. QTY. DESCRIPTION NOTE: Effective August 2006, the Venturi and product delivery tubing was changed from .25"ID to .375"ID to improve flow rate. If for first replacement, order Tube Replacement Kit P/N 39169.0000 (2 kits required for TCD-2) 1 23820.1000 1 Water Strainer Assy (Includes items 2 thru 4) 2 22249.0000 1 Cap, Water Strainer 3 23721.0000 1 Screen 4 23819.0000* 1 Housing (Order item 1) 5 00310.
TCD-1 TCD-2 REPLACEMENT PARTS (TCD-1) (continued) 56 57 59 58 57 43 .375" BIB Adapter 42 Concentrate Bottle Tube 20 24 26 46 47 18 15 19 17 16 61 21 2 3 1 4 5 19 31 30 20 22 32 20 52 7 26 27 28 29 23 54 6 45 20 20 14 13 12 11 10 44 34 35 51 33 53 8 25 9 36 37 38 39 60 41 40 49 47 48 50 55 Early Models P3457.60 8 34106.
REPLACEMENT PARTS (TCD-1) ITEM PART NO. QTY. DESCRIPTION 28 37691.0000 1 O-ring 29 37486.0000 1 Adjustment Screw, Venturi 30 32852.0000 1 O-ring 31 03093.0001 01268.0000 1 1 Wing Nut, Faucet Chrome Nut, Faucet Union (Optional) 32 01221.0001 1 C-Ring, Faucet Shank 33 03260.0004 1 Faucet Assy, Black Plastic Body (Includes items 34 thru 40)(Refer to page 18 for important ordering information)(See item 67) 03260.
TCD-1 TCD-2 REPLACEMENT PARTS (TCD-1) (continued) 56 57 59 58 57 43 .375" BIB Adapter 42 Concentrate Bottle Tube 20 24 26 46 47 18 15 19 17 16 61 21 2 3 1 4 5 19 31 30 20 22 32 20 52 7 26 27 28 29 23 54 6 45 20 20 14 13 12 11 10 44 34 35 51 33 53 8 25 9 36 37 38 39 60 41 40 49 47 48 50 55 Early Models P3457.60 10 34106.
REPLACEMENT PARTS (TCD-1) ITEM PART NO. QTY. DESCRIPTION 56 26443.0000 34644.0000 1 1 Reducer, Barb .375" x .25" Connector, Barb .375" x .375" 57 12422.0001 2 Clamp, Hose .59"/.66" 58 37720.0000* 1 Tube, Silicone .375" ID x 3.0" (Order item 64) 59 37744.0000 37744.0001 1 1 Tube, Concentrate Bottle .25" Tube, Concentrate Bottle .375" 60 39216.0000 1 Screen Filter (Late Models) 61 27574.0000 1 Sealing Washer For use with .
TCD-1 TCD-2 REPLACEMENT PARTS (TCD-2) 62 63 50 47 48 49 48 Concentrate Bottle Tube 51 .375" BIB Adapter 48 46 Bag Divider 28 29 56 60 23 30 21 18 24 17 19 20 24 16 22 15 65 7 64 35 34 36 25 55 8 24 27 14 13 12 11 10 6 29 31 32 33 25 58 26 48 57 37 59 9 40 41 42 43 2 45 3 1 4 5 38 39 53 61 54 52 44 60 Early Models P3462.60 12 34106.
REPLACEMENT PARTS (TCD-2) ITEM PART NO. QTY. DESCRIPTION NOTE: Effective August 2006, the Venturi and product delivery tubing was changed from .25"ID to .375"ID to improve flow rate. If for first replacement, order Tube Replacement Kit P/N 39169.0000 (2 kits required for TCD-2) 1 23820.1000 1 Water Strainer Assy (Includes items 2 thru 4) 2 22249.0000 1 Cap, Water Strainer 3 23721.0000 1 Screen 4 23819.0000* 1 Housing (Order item 1) 5 00310.
TCD-1 TCD-2 REPLACEMENT PARTS (TCD-2) (continued) 62 63 50 47 48 49 48 Concentrate Bottle Tube 51 .375" BIB Adapter 48 46 Bag Divider 28 29 56 60 23 30 21 18 24 17 19 20 24 16 22 15 65 7 64 35 34 36 25 55 8 24 27 14 13 12 11 10 6 29 31 32 33 25 58 26 48 57 37 59 9 40 41 42 43 2 45 3 1 4 5 38 39 53 61 54 52 44 60 Early Models P3462.60 14 34106.
REPLACEMENT PARTS (TCD-2) ITEM PART NO. QTY. DESCRIPTION 31 37487.1001 1 Venturi Mixer (Includes items 35 & 36) 32 37691.0000 1 O-ring 33 37486.0000 1 Adjustment Screw, Venturi 34 03093.0001 01268.0000 2 2 Wing Nut, Faucet Chrome Nut, Faucet Union (Optional) 35 32852.0000 2 O-ring 36 01221.0001 2 C-Ring, Faucet Shank 37 03260.
TCD-1 TCD-2 REPLACEMENT PARTS (TCD-2) (continued) 62 63 50 47 48 49 48 Concentrate Bottle Tube 51 .375" BIB Adapter 48 46 Bag Divider 28 29 56 60 23 30 21 18 24 17 19 20 24 16 22 15 65 7 64 35 34 36 25 55 8 24 27 14 13 12 11 10 6 29 31 32 33 25 58 26 48 57 37 59 9 40 41 42 43 2 45 3 1 4 5 38 39 53 61 54 52 44 60 Early Models P3462.60 16 34106.
REPLACEMENT PARTS (TCD-2) ITEM PART NO. QTY. DESCRIPTION 59 00651.0000 1 Decal, BUNN 60 38278.0002* 2 Edging 36.0" (Order item 72) 61 38839.0000 1 Stand 62 38745.1000 1 Bag Divider (Includes Item 63) 63 38278.0001* 38278.0003* 1 2 Edging 9.5" (Order item 72) Edging 1.0" (Order item 72) 64 39216.0000 1 Screen Filter (Late Models) 65 27574.0000 1 Sealing Washer The Following Items Are Not Illustrated 66 00674.0000 00674.
ICED TEA DECAL PLACEMENT APPROX. 5“ PLASTIC BODY FAUCET COMPARISON If you have a plastic body faucet of this design, you must order a complete new plastic faucet. New Plastic Faucet Design 18 34106.
