Manual

ManualsBrandsBurcam ManualsPumps300402 SUMP BUDDY SUBM. BACK UP MUNICIPAL WATER SUMP PUMP

2190 Boul. Dagenais West TEL: 514.337.4415

LAVAL (QUEBEC) FAX: 514.337.4029

CANADA

H7L 5X9 info@burcam.com

INSTALLATION

INSTRUCTIONS

MODEL

300402

SUMP

BUDDY

Please read these

instructions

carefully. Failure

to comply to

instructions and

designed

operation of

this system,

may void the

warranty.

Your pump has been

carefully packaged at the

factory to prevent damage

during shipping. However,

occasional damage may

occur due to rough handling.

Carefully inspect your

pump for damages that

could cause failures.

Report any damage to your

carrier or your point of

purchase.

ELECTRICAL PUMP

AND PIPING NOT

INCLUDED

WWW.BURCAM.COM

Summary of content (8 pages)

PAGE 1
INSTALLATION INSTRUCTIONS W W W. B U R C A M . C O M 2190 Boul. Dagenais West LAVAL (QUEBEC) CANADA H7L 5X9 MODEL 300402 TEL: 514.337.4415 FAX: 514.337.4029 info@burcam.com SUMP BUDDY ELECTRICAL PUMP AND PIPING NOT INCLUDED Please read these instructions carefully. Failure to comply to instructions and designed operation of this system, may void the warranty. Your pump has been carefully packaged at the factory to prevent damage during shipping.
PAGE 2
SAFETY INSTRUCTIONS:(applicable to your electrical primary pump) This fine pump that you have just purchased is designed from the latest in material and workmanship. Before installation and operation, we recommend the following procedures: A CHECK WITH YOUR LOCAL ELECTRICAL AND PLUMBING CODES TO ENSURE YOU COMPLY WITH THE REGULATIONS. THESE CODES HAVE BEEN DESIGNED WITH YOUR SAFETY IN MIND. BE SURE YOU COMPLY WITH THEM.
PAGE 3
APPLICATION This pump is designed to be connected to any existing conventional type sump pump system, as an extra sump pump protection. FEATURES Extra protection during power outage or in the event of failure of conventional sump pump. Easy to connect to existing conventional sump pump discharge line. CAPACITY AT 60 PSI (municipal water pressure): 5’ 581 US GPH 10’ 317 US GPH 15’ 158 US GPH Friction loss in pipe not included Automatic control valve activate the SUMP BUDDY. No electricity required.
PAGE 4
STEP 5 Close municipal water supply. Run a supply line (not less than 1/2”, 3/4” recommended) to the ideal position for an easy operation of the automatic control valve of the SUMP BUDDY. Install a ball valve near the pump area, to close water supply for servicing at a later date. STEP 6 Flush this new line, before next step, to remove any debris which may obstruct the water flow in your SUMP BUDDY. STEP 7 Screw the automatic control valve to the supply line.
PAGE 5
TYPICAL INSTALLATION DIAGRAM FOR SUMP PUMP STEP 1 Install with solid discharge line from 1 1/4” to 2” pipe size. STEP 6 Flush line to remove debris. STEP 5 Run a supply line with a ball valve near pump area. STEP 11 Install float and rod to automatic valve. STEP 3 Install T or Y fitting and link discharge lines together. STEP 7 Screw automatic control valve. STEP 12 Fix vacuum breaker. This ejector is press fit fixed. Do not try to unscrew, you will damage and void warranty.
PAGE 6
TYPICAL INSTALLATION DIAGRAM FOR COLUMN PUMP STEP 1 Install with solid discharge line from 1 1/4” to 2” pipe size. STEP 6 Flush line to remove debris. STEP 5 Run a supply line with a ball valve near pump area. STEP 11 Install float and rod to automatic valve. STEP 3 Install T or Y fitting and link discharge lines together. STEP 7 Screw automatic control valve. This ejector is press fit fixed. Do not try to unscrew, you will damage and void warranty. Please call us to make maintenace at 1-800 361-1820.
PAGE 7
REPAIR PARTS LIST REF. PART DESCRIPTION 1 2 3 4 5 6 7 8 9 10 11 REF. 350250 350254K 350255 350254 350256 350257 350353A 350253 350252 350251 350260 PART Pump body Ejector kit (incl.
PAGE 8
TROUBLE SHOOTING GUIDE CHECKLIST NEVER MAKE ADJUSTMENTS TO ANY ELECTRICAL APPLIANCE OR PRODUCT WITH THE POWER CONNECTED. DON’T JUST UNSCREW THE FUSE OR TRIP THE BREAKER, REMOVE THE POWER FROM THE RECEPTACLE. TROUBLE PROBABLE CAUSE No water is drawn out. Municipal water supply closed. Automatic valve closed. Float do not rise with water level. Suction or ejector clogged. Water level below suction in sump. Improper function or missing check valve in primary pump discharge. Discharge line clogged.