Technische Daten Betriebsspannung DC 3V Max. Eingangsleistung 1 × CR2032 (3V) Max. Betriebsstrom 20 mA Max. Standby 2μA Max. Reichweite außen Max. Reichweite innen Ohne Hindernis 200 m* 50 m* Übertragungsfrequenz 433.05 - 434.79 MHz Max.
Verbindung mit der Base 1. Starten Sie die App. 2.
. Scannen Sie den QR Code des Gerätes. Nach dem erfolgreichen Scannen können Sie einen beliebigen Namen für das Gerät vergeben, z.B. „Wohnzimmertür“ 4. Die App meldet Ihnen wenn das Hinzufügen zur Anlage erfolgreich war.
Batteriewechsel 1. Öffnen Sie das Gehäuse mit Hilfe eines flachen Schraubendrehers. Führen Sie den Schraubendreher hierzu vorsichtig in den Schlitz an der Seite des Melders ein, an welcher sich die Status-LED befindet. 2.
Richtiger Installationsort Das Funksignal des Sensors ist stark von den Umgebungsbedingungen abhängig. Metallgegenstände, Betondecken, Wände, metallische Leitungen etc. verringern die Reichweite. Störungen können auch durch andere Funksender und Umgebungseinflüsse auftreten. WICHTIGER HINWEIS: Der Melder kann nur so gut funktionieren, wie es die Installation und Umgebung zulässt. Der Melder kann die Gefahrensituation anzeigen aber nicht vermeiden.
Installationshinweise 1. Entfernen Sie zuerst den Batteriestreifen aus dem Sensor. 2. Richten Sie den Sensor vor der Installation, per App, an der Base ein und testen Sie die Funktion. 3. Befestigen Sie den Magneten und Sender mit Klebestreifen oder Schrauben (nicht im Lieferumfang enthalten) an der gewünschten Position. 4. Vermeiden Sie die Installation auf metallischen Flächen und in der Nähe von stromführenden Kabeln. 5. Sollte die Status LED permanent leuchten, wechseln Sie bitte die Batterie.
Allgemeine Sicherheitshinweise und Vorsichtsmaßnahmen Vorsicht Änderungen und Modifizierungen, die nicht ausdrücklich durch die zuständige Genehmigungsbehörde genehmigt worden sind, können zum Entzug der Genehmigung zum Betreiben des Gerätes führen. Dieses Gerät entspricht den CE-Richtlinien.
Haftungsbeschränkung Das vorliegende Gerät entspricht dem aktuellen technischen Standard zum Zeitpunkt der Herstellung. Wir sind fortlaufend bestrebt unsere Ware auf dem neuesten technischen Stand der Technik und Handbücher Up to Date zu halten. Daher behalten wir uns vor, technische Änderungen und Überarbeitung/ Anpassung der Anleitung ohne vorherige Ankündigung vorzunehmen. Der Inhalt der Anleitung ist sorgfältig zu lesen. Für Schäden, z.B.
Sicherheitshinweise Lesen Sie die Anleitung sorgfältig durch. Für durch Nichtbeachten entstandene Schäden wird keine Haftung übernommen. Das Gerät ist ausschließlich für den in der Anleitung genannten Zweck einzusetzen. Das Gerät soll Sie im Ernstfall informieren und alarmierend wirken! Bitte prüfen Sie die Funktion und den Batteriestand des Gerätes daher regelmäßig um für den, hoffentlich nicht eintreffenden, Ernstfall gewappnet zu sein.
WICHTIGER HINWEIS: Bei Platzierung an einem ungünstigen Standort kann es zu Beeinträchtigung(en) der Funktion(en) kommen. Wenn Sie eine EG-Konformitätserklärung für dieses Gerät benötigen, schicken Sie bitte eine Anfrage an: info@burg.biz Reinigung Benutzen Sie ausschließlich minimal feuchte Tücher für die Reinigung. Achten Sie darauf, dass kein Wasser in das Gerät eindringt. Benutzen Sie keine leicht brennbaren, chemischen, ätzenden, scheuernden oder scharfen Reinigungsmittel.
n u ür ine Die Gewährleistung beinhaltet ausschließlich Mängel welche nachweislich auf Herstellungsoder Materialfehler zum Verkaufszeitpunkt zurückzuführen sind. Die Gewährleistung endet nach zwei Jahren, weitere Ansprüche sind ausgeschlossen. Festgestellte Mängel müssen schriftlich, inkl. Original-Kaufbeleg und kurzer Fehlerbeschreibung, bei Ihrem Verkäufer eingereicht werden.
Weiteres Zubehör: Sirene 2150 Control 2110 Smoke 2050 Outdoor Sirene Fernbedienung Rauchmelder Vibrancy 2020 Vibrations-Sensor Contact 2030 Motion 2010 Water 2060 Wassermelder Keypad 2100 Tür- und Fensterkontakt PIRBewegungsmelder RFID-Tastatur Set 2200 Alarmanlage Startpaket bestehend aus: 1x 1x Control 2110 16 | Deutsch 1x Motion 2010 2x Contact 2030 WATER 2060
2020 Weiteres Zubehör finden Sie auf unserer Homepage: www.burg.biz oder durch scannen des folgenden QR Code Links: Sensor 0 Entsorgung des Gerätes Wir weisen darauf hin, dass derart gekennzeichnete Elektro- und Elektronikgeräte sowie Batterien, nicht über den Hausmüll, sondern getrennt bzw. separat gesammelt werden müssen. Bitte erkundigen Sie sich bei der zuständigen Stelle in Ihrer Stadt / Gemeinde nach Sammelstellen für Batterien und Elektromüll.
Hiermit erklärt die BURG-WÄCHTER KG, dass das vorliegende Gerät den Richtlinie 2014/53/EU, (RED) 2014/30/EU, (EMC), und der 2011/65/EU (RoHS) entspricht. Der vollständge Text der EU-Konformitätserklärung ist unter der folgenden Internetadresse abrufbar: www.burg.biz Bei technischen Fragen zum Produkt lesen Sie bitte die ausführliche Bedienungsanleitung und beachten Sie die FAQ, die Sie auf folgender Webseite finden: www.burg.biz.
Impressum Das Copyright dieser Bedienungsanleitung liegt ausschließlich bei der BURG-WÄCHTER KG. Jegliche Vervielfältigung auch auf elektronischen Datenträgern bedarf der schriftlichen Genehmigung der BURGWÄCHTER KG. Der Nachdruck – auch auszugsweise – ist verboten. Irrtum und technische Änderungen vorbehalten. Alle genannten Firmen- und Produktnamen sind Warenzeichen oder eingetragene Warenzeichen bzw. Marken der jeweiligen Inhaber. Irrtum und technische Änderungen vorbehalten.
Items included in delivery 1 x Quick installation guide 1 x BURGprotect WATER 2060 1 x Batterie (1 × CR2032, 3V) 1 x Glue sticker Features The wireless water intrusion sensor is an accessory of smartBURG alarm system. It‘s fashion design, energy saving, and low battery warning supported. The system would inform users to replace the battery by App when needed. It‘s easy to setup and informs user when detecting water intrusion.
Parameters Working Voltage DC 3V Battery 1 × CR2032 (3V) Working Current 20 mA Standby Current 2μA Transmission Distance Without obstacle 200 m* Indoor max 50 m* Transmission Frequency 433.05 - 434.79 MHz Max.
Pairing Sensor with Base 1. Launch the App. 2.
3. Scan the QR code, printed on this accessory, by App. After scanning, you may rename the accessory, e.g. „living room door“ 4. The App will auto recognize this accessory. Please wait until the app notes the successful add.
Battery replacement instructions 1. Insert the flat blade of a small screwdriver into the pry-off slot of transmitter, twist the blade to remove the cover. 2.
Correct location for installation The radio signal of the sensor is highly dependent on environmental conditions. Metal objects, concrete surfaces, walls, and metal cables all reduce its range, etc. Other radio devices and environmental conditions can also interfere with its operation.. IMPORTANT NOTE: The alarm can only work as well as permitted by its installation and environment. The alarm can indicate dangerous situations but it cannot prevent them.
Installation & Notice 1. Remove the battery insulative strip. 2. Before you install, set the sensor to the base using the app and test the function. 3. Attach the magnet and transmitter to the desired position using adhesive strips or screws (not included). 4. Avoid installing on metallic surfaces and near live cables. 5. If the status LED is permanently lit, please change the battery. Do not use batteries. 6. Ensure that the distance between the magnet and the detector is significantly less than 1cm.
General safety precautions and safety instructions CE-compliance This appliance complies with the CE guidelines. If you require an EC Declaration on Conformity for this device for this device, please send a request to: info@burg.biz Attention Any changes or modifications to this appliance which have not been explicity approved of by the respective regulatory authority, may lead to a prohibition of usage of this appliance..
Limitation of liability This device complies with the technical standards in force at the time of production. We constantly strive to ensure that our products are technologically cutting edge and that our handbooks are kept up to date. We therefore reserve the right to undertake technical changes and modifications or adjustments to the instructions without providing advance notice. The instructions must be carefully followed. We accept no liability for damage, as a result of e.g.
Safety guidelines Please read the instructions carefully. No liability can be assumed for any damage which may result from failure to follow instructions. The device must be used only for the purpose specified in the instructions. The device should work effectively as an alarm in an emergency! Please check regularly that the device is in working order and that the batteries are charged. This will ensure that it functions correctly in the event of a (hopefully unlikely) emergency.
The device may malfunction when exposed to unexpectedly high electromagnetic radiation, manipulation or other influences. The device must not be installed in damp areas or near electrical devices which emit radiation. Battery-operated devices must not be used in high temperatures, near sources of heat or exposed to direct sunlight. Ensure that packaging and contents are kept well away from children to avoid any risk of suffocation. Please keep instructions in a safe place.
to , must cal r t n Guarantee BURG-WÄCHTER products comply with the technical standards in force at the time of production and adhere to our own quality standards. The guarantee only covers defects which can be proved to have resulted from production or material defects at the time of purchase. The guarantee expires after two years; further claims are excluded.
Additional accessory: Sirene 2150 Control 2110 Smoke 2050 Outdoor Siren Remote Controller Smoke detector Vibrancy 2020 Vibrancy Sensor Contact 2030 Motion 2010 Water 2060 Water Intruction Door- and window contact PIR- sensor Keypad 2100 Keypad Set 2200 1x Alarm starter kit: 1x Control 2110 32 | English 1x Motion 2010 2x Contact 2030 WATER 2060
2020 You can find more Accessories on our homepage www.burg.biz or by App: ensor 0 Disposal Please be aware that electrical and electronic equipment and batteries shall not be disposed of as household waste, but rather collected separately. Please obtain information on the collecting points for electrical waste from the responsible authority of you municipality.
BURG-WÄCHTER KG hereby declares that this device complies with Directive 2014/53/EU, (RED) 2014/30/EU, (EMC) and 2011/65/EU (RoHS). The full text of the EU Declaration of Conformity can be found on www.burg.biz. The full text of the EU Declaration of Conformity can be found on the following website www.burg.biz f you have technical questions about this device, please read the detailed user manual and the FAQ sheet which you will find on the following website: www.burg.biz.
Copyright All rights reserved. This publication may not be reproduced, stored in a retrieval system or transmitted, in any form or by any means (electronic, mechanical, photocopying, recording or otherwise), without the written prior permission of BURG-WÄCHTER KG. No reproduction of any part or excerpts thereof are permitted. Errors excepted. Specifications are subject to change without notice for quality improvement.
Notes 36 | English WATER 2060