Data Sheet

ManualsBrandsBürkert ManualsAutomation & PneumaticsBürkert Air-operated valve 146358 2012 G2 sleeve 1 pc(s)

2012

p. 1/18www.burkert.com

2/2 way Globe Valve

for media up to + 180 °C, DN10 - 100

The externally piloted globe valve consists of

a pneumatically operated piston actuator and

a 2/2 way valve body. The actuator is made of

PA or, for special operating conditions, PPS. The

reliable self-adjusting packing gland provides

high sealing integrity. These maintenance-

free and robust valves can be retro-ﬁtted with

a comprehensive range of accessories for

position indication, stroke limitation or manual

override.

Type 2012 can be combined with...

• Compact globe valve version

• Flange, threaded and welded ports as standard

• Stainless steel 316L valve body

• Available with flow direction below and above seat

Note: For PA actuators in the sizes 40, 50

and 63, the combination of max. media

temperature and max. ambient temperature

is as shown in the following chart:

Technical data

Oriﬁce

DN10 … 100

Body material

Cast stainless steel 316L

Actuator material

PA, PPS

Seal material

PTFE (NBR, FKM and EPDM on request)

Medium

Water, alcohol, oils, fuel, salt solution, alkali solutions,

organic solvents, steam

Viscosity

Max. 600 mm

Packing gland

(with silicone grease)

PTFE

Nominal pressure

PN25 (body)

Medium temperature

- 10 … + 180 °C with PTFE seal

Ambient temperature

PA actuator

Actuator sizes up to Ø 125

Actuator sizes Ø 175 … 225

PPS actuator

Actuator sizes Ø 40 … 80

Actuator sizes Ø 100 … 125

- 10 … + 60 °C

- 10 … + 50 °C

+ 5 … + 140 °C

+ 5 … + 90 °C

Installation

As required, preferably with actuator in upright position

Control medium

Neutral gases, air

Max. pilot pressure

Actuator size Ø 40 … 80

Actuator size Ø 100

Actuator size Ø 125

Actuator size Ø 175 … 225

PA and PPS 10 bar

PA 10 bar

PPS 7 bar

PA and PPS 7 bar

PA 6 bar

Valve speciﬁcations System spec. On/Off Classic

Request for quotation

Type 2012 Type 8801-GA

Type 8801-GA

Technical data & ordering info.

p. 1 - 14

Ordering info. & technical data

p. 15 - 16 p. 17

Typ 8697

Electrical

position feedback

Type 8640/8644

Valve block

Type 6012/6014 P

Pilot valve

Type 5470

Solenoid valve

For process valves

with decentralized

automation see

ELEMENT Type 2101

Content

100

120

140

160

180

200

Ø 50

Ø 40

Ø 63

Ambient temp. °C

Mediums temperature °C

Summary of content (18 pages)

PAGE 1
2012 2/2 way Globe Valve for media up to + 180 °C, DN10 - 100 • Compact globe valve version • Flange, threaded and welded ports as standard • Stainless steel 316L valve body • Available with flow direction below and above seat Type 2012 can be combined with...
PAGE 2
012 Materials Actuator size 40 … 125 mm 1 1 Transparent cap PC, PSU 2 2 Actuator PA, PPS 3 4 5 6 7 8 3 Cylinder seal NBR, FKM 4 Pilot air ports Stainless steel 1.4305 5 V-seals PTFE, FKM 6 Nipple Stainless steel 1.4401 7 Wiper - PTFE 8 - PEEK Actuator size 100 mm and 125 mm Spindle Stainless steel 1.4401 9 Swivel plate Stainless steel 1.4401 10 Pin Stainless steel 1.4401 11 Seal PTFE (NBR, FKM, EPDM on request) 12 Valve seat Stainless steel 1.
PAGE 3
2012 Technical data for valves with flow direction below the seat Flow direction below seat Type 2012 with flange port connection ➔ Orifice Actuator size KV value water Minimum pilot pressure Maximum operating pressure up to + 180 ºC Weight with CFA Flange Threaded port and weld end [mm] [mm] (m3/h) CFA [bar] CFA [bar] CFB [bar] [kg] [kg] 10 40 4.7 4.0 15 16 2.3 0.8 50 4.7 3.9 16 16 2.4 0.9 40 4.7 4.0 15 16 2.3 0.8 50 4.7 3.9 16 16 2.4 0.9 40 8.1 4.0 6.
PAGE 4
2012 Ordering chart for valves with flow direction below the seat (other versions on request) ➔ Valves with stainless steel body and flange connection according to DIN EN 1092-1, flow below seat Control function Orifice [mm] Actuator size Ø [mm] 10 A 2 (P) 1 (A) Pneumatically operated on / off valve, normally closed by spring force, flow direction below seat Operating pressure up to + 180 °C [bar] Article no. PA actuator Article no. PPS actuator 40 4.7 4.0 15 146227  146362  4.7 3.
PAGE 5
2012 Ordering chart for valves with flow direction below the seat (other versions on request), cont.
PAGE 6
2012 Ordering chart for valves with flow direction below the seat (other versions on request), cont. ➔ Valves with stainless steel body and weld end according to EN ISO 1127/ISO 4200, flow below seat Control function Orifice [mm] 10 A Weld end EN ISO 1127/ ISO 4200 external Ø x Ws [mm] 17.2 × 1.6 2 (P) Article no. PPS actuator 146364  40 4.7 4.0 15 50 4.7 3.9 16 146229  146239  4.7 4.0 15 146249  40 50 4.7 3.9 16 146261  20 26.9 × 1.6 40 8.1 4.0 6.
PAGE 7
2012 Ordering chart for valves with flow direction below the seat (other versions on request), cont. ➔ Valves with stainless steel body and weld end according to DIN 11850 Series 2, flow below seat Weld end Orifice DIN 11850 S2 external Ø x [mm] Ws [mm] Control function A 10 13 × 1.5 2 (P) 15 19 × 1.5 1 (A) 20 Pneumatically operated on / off valve, normally closed by spring force, flow direction below seat 25 29 × 1.5 32 35 × 1.5 40 41 × 1.5 50 53 × 1.5 65 70.0 × 2.0 80 85.0 × 2.
PAGE 8
2012 Technical data for valves with flow direction above the seat Flow direction above seat Type 2012 with flange connection ➔ Orifice Technical data Flow direction above the seat Medium Gaseous medium and steam Other technical data Please see technical data for flow direction below seat KV value water [m3/h] Operating pressure up to + 180 ºC [bar] Weight with flange [kg] Threaded port and weld end [kg] [mm] Actuator size [mm] 10 40 3.0 16 2.3 0.8 50 3.0 16 2.4 0.9 15 40 4.
PAGE 9
2012 Ordering chart valves with flow direction above the seat (other versions on request) ➔ Valves with stainless steel body and flange connection according to DIN EN 1092-1, flow above seat Control function Orifice [mm] A Connection 4.7 Operating Minimum pressure up pilot pressure to + 180 °C [bar] [bar] 16 Article no. PA actuator Article no. PPS actuator 146427  – 16 146432  16 146437  146492  – Flange Flange 50 4.7 15 Flange 40 4.7 50 4.7 16 146443  20 Flange 40 8.
PAGE 10
2012 Ordering chart valves with flow direction above the seat (other versions on request), cont. ➔ Valves with stainless steel body and weld end according to EN ISO 1127/ISO 4200, flow above seat Control function A 2 (A) 1 (P) Pneumatically operated on / off valve, normally closed by spring force, flow direction above seat Orifice [mm] Weld end external Ø x Ws [mm] 10 17.2 × 1.6 15 21.3 × 1.6 Actuator size Ø [mm] KV value water [m3/h] 40 4.7 50 4.
PAGE 11
2012 Ordering chart for accessories 3/2 way pilot valves with banjo bolts Seal material valve FKM, seal material banjo bolt NBR Valve for actuator size [Ø mm] Type Pressure inlet P (valve body) Service port A (banjo bolt) Orifice [mm] QNn value air [l/min] Pressure range [bar] Electrical coil connection Ind. Std. Power consumption [W] 40 6012P G⅛ 1.2 48 0 … 10 Form B 4 Article no. Voltage/ frequency [V/Hz] 024/DC 230/50 40 6012P Tube fitting Ø6 mm G⅛ G⅛ 1.
PAGE 12
2012 Dimensions [mm] Threaded and weld end DN10 … 50 ØE With threaded port connection ØE With weld end acc.
PAGE 13
2012 Dimensions [mm] , continued Flange connection C DN10 … 100 Actuator size 40 … 125 mm DN65 … 100 Actuator size 175 and 225 mm C ØE F Ø DF BF Axa Axα ØM Ø DF Ø BF Ø D F Ø D H H J K K J ØE AF AF LF All bodies DIN flange LF JIS flange DN Actuator C ØE F H K J ØDF LF ØBF AF ØD Axα ØM ØDF LF ØBF AF ØD Axα ØM 10 40 33 53 116 185 G⅛ 16.
PAGE 14
2012 Dimensions [mm], continued Flange connection All bodies ANSI flange DN Actuator C ØE F H K J ØDF LF ØBF AF ØD Axα ØM ½" 40 33 53 116 185 G⅛ 16.5 89 184 60.5 11.2 15.7 4 × 90º 16 50 44 64 131 211 G¼ 24 89 184 60.5 11.2 15.7 4 × 90º 16 40 33 53 118 187 G⅛ 16.5 99 184 69.9 12.7 15.7 4 × 90º 21 50 44 64 135 213 G¼ 24 99 184 69.9 12.7 15.7 4 × 90º 21 63 52 80 155 247 G¼ 24 99 184 69.9 12.7 15.
PAGE 15
2012 System On/Off CLASSIC 8801-GA Ordering information for valve system On/Off CLASSIC Type 8801-YA An globe valve Type 2012 can be combined with the feedback Type 8697 to form a valve system On/Off CLASSIC. The valve system On/Off CLASSIC is composed of: More . • a feedback Type 8697 (see separate datasheet) info • a globe valve Type 2012 (see ordering chart p. 4) For the configuration of further valve systems please use the “Request for quotation” on p.
PAGE 16
2012 System On/Off CLASSIC 8801-GA Dimensions for valve system On/Off Classic Type 8801-GA [mm] Dimensions valve system On/Off Classic Type 8801-GA with electrical position feedback Type 8697 Weld end Flange Ds G Ws DF M H HM H Threaded LM Port Actuator connection size [mm] [mm] 10 15 20 25 32 40 50 65 80 Threaded Weld end DIN 11850 Weld end EN ISO 1127 / ISO 4200 Flange DIN EN 1092-1 HM ØG LM H Ds Ls Ws H Ds Ls Ws H ØDF DF ØM 40 286 G⅜ 65 286 13 90 1.5 286 17.
PAGE 17
2012 System On/Off CLASSIC 8801-GA Note fill out You can directly s ld fie the file F D P in the nting before pri rm. out the fo Valve system On/Off Classic Type 8801-GA – request for quotation Please fill out and send to your nearest Bürkert facility* with your inquiry or order Company Contact person Customer no. Department Address Tel.
PAGE 18
2012 System On/Off CLASSIC 8801-GA Valve system On/Off Classic Type 8801-GA – request for quotation, continued Valve accessories Pilot valve Pilot valve Power supply Stroke limitation Stroke limitation Min./max. stroke limitation, with visual position indicator Max. stroke limitation, without visual position indicator Please specify item no. if known: Please specify item no. if known: Certifications Attestation of compliance with the order EN-ISO 10204 2.1 Test report EN-ISO 10204 2.