AutoDome™ System TC700 Series Camera, Lens, Pan/Tilt, and Receiver/Driver Modules User’s Manual
points or short-out parts that could result in a fire or electric shock. Never spill liquid of any kind on the unit. IMPORTANT SAFEGUARDS 16. Servicing - Do not attempt to service this unit yourself as opening or removing covers may expose you to dangerous voltage or other hazards. Refer all servicing to qualified service personnel. 1. Read Instructions - All the safety and operating instructions should be read before the unit is operated. 2.
Safety Precautions Securite CAUTION ATTENTION RISK OF ELECTRIC SHOCK. DO NOT OPEN! RISQUE DE CHOC ELECTRIQUE. NE PAS OUVRIR. CAUTION: TO REDUCE THE RISK OF ELECTRICAL SHOCK, DO NOT OPEN COVERS. NO USER SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. Danger: Pour éviter tout risque d'électrocution, ne pas ouvrir le boîtier. Il n'y a pas de pièces remplaçables à l'intérieur. Pour toute révision, s'adresser à un technicien spécialisé.
Sicherheitsvorkehrungen Precauciones de Seguridad VORSICHT PRECAUCION RISIKO EINES ELEKTRISCHEN SCHLAGES NICHT ÖFFNEN! R IESG O D E C HOQ U E ELEC TRICO . ¡N O ABRIR! VORSICHT: UM EINEN ELEKTRISCHEN SCHLAG ZU VERMEIDEN, ABDECKUNG NICHT ENTFERNEN. WARTUNGEN ALLER ART QUALIFIZIERTEM PERSONAL ÜBERLASSEN. Precaucion: Para Reducir El Riesgo De Choque Eléctrico, Favor No Abrir La Cubierta. Este Equipo No Consta De Piezas O Partes Que Requieren Servicio O Mantenimiento.
TC700 Series - Camera, Lens, Pan/Tilt, and Receiver/Driver Modules Monochrome Models Model No. TC750-4-1 TC750-4-2 TC750-6-1 TC750-6-2 TC750-9-1 TC750-9-2 TC750X-4-1 TC750X-4-2 TC750X-6-1 TC750X-6-2 TC750X-9-1 TC750X-9-2 ATTENTION OBSERVE PRECAUTIONS FOR HANDLING ELECTROSTATIC SENSITIVE DEVICES WARNING: Electrostatic-sensitive device. Use proper CMOS/MOSFET handling precautions to avoid electrostatic discharge.
DESCRIPTION OPERATION The TC700 Series AutoDome™ systems are quiet, lightweight, and discreet surveillance dome systems containing high sensitivity 1/3-inch image format full performance monochrome or color CCD cameras with a 10:1 auto-iris, auto-focus zoom lens, a high-speed pan/tilt, and an intelligent, integral receiver/driver. The one-piece camera, lens, pan/tilt, and receiver/driver module is housed in a domed enclosure.
Notes: 1. The following settings are stored with pre-position scenes: Pan position. Tilt position. Zoom position. Focus mode AUTO/MANUAL. Focus position for MANUAL mode. Iris mode AUTO/MANUAL. Iris ALC/LEVEL for AUTO mode or position for MANUAL mode. White Balance mode AUTO/MANUAL (color cameras only). Red content and Blue content for MANUAL mode (color cameras only). Shutter mode ON/OFF. Shutter setting for ON mode. Backlight compensation ON/OFF. Highlight ON/OFF (monochrome cameras only).
Executing Playback: 1. Press ON, AUX 50, ENTER for continuous playback. DIP Switch Settings 1 2 3 Off Off Off On Off Off Off On Off On On Off Off Off On On Off On Off On On On On On 2. Press ON, AUX 51, ENTER for single playback. Stopping Playback: 1. Press Off, AUX 50 or AUX 51, ENTER or move joystick. Resuming Playback After Stopping During Playback: 1. After stopping during playback, press On, AUX 52, ENTER.
side of the AC power input to the dome. This is the "zero phase delay" position. The phase delay between the AC line zero crossing and camera vertical sync can range to 360 degrees, with respect to the original "zero phase" position. The 360 degree range is divided into 362 steps for NTSC cameras and 370 steps for PAL cameras, so that very fine adjustment of the phase delay is possible. Backlight Compensation Off: Issuing this command disables the camera's backlight compensation mode. (AUX 20 - Off.
since both zones are the same. A dome operator can see where the backlight compensation zone will average in the field-of-view. Manual White Balance - Increase Red: Issuing this command increases the red content of the picture by one step. (AUX 31 - On.) Electronic Shutter (AUX 22, 23) Manual White Balance - Decrease Red: Issuing this command decreases the red content of the picture by one step. (AUX 31 - Off.
ILLUSTRATIONS Site Address Thumbwheel DIP Switches Remove Screw & Shipping Bracket Prior to Operation Tilt Motor Remove Foam Prior To Operation Connector S9407002AE TC700 Series - Camera, Lens, Pan/Tilt, and Receiver/Driver Module 11
Patented under U.S. Patent No. 5,517,236 ALL SPECIFICATIONS SUBJECT TO CHANGE WITHOUT NOTICE. INFORMATION FURNISHED BY PHILIPS COMMUNICATION & SECURITY SYSTEMS INC. (PCSS) IS BELIEVED TO BE ACCURATE AND RELIABLE. HOWEVER, NO RESPONSIBILITY OR LIABILITY IS ASSUMED BY PCSS FOR ITS USE, NOR FOR ANY INFRINGEMENT OF PATENTS OR OTHER RIGHTS OF THIRD PARTIES WHICH MAY RESULT FROM ITS USE. NO LICENSE IS GRANTED BY IMPLICATION OR OTHERWISE UNDER ANY PATENT OR OTHER RIGHTS OF PCSS.
