Brochure
Baseray
®
Baseboard
Information, Specifications, & Dimensions
1. Fins
2. Tie Bolt
3. Push Nipple
A B C D E F G
1” 7/8” 2-1/2” 9-7/8” 1-3/4” 1-3/4” 3/4”
Use of the 2,000 Lb./Hr. ratings is limited to installations where the flow rate through the baseboard unit is equal to or greater than 2,000 Lb./Hr. (4GPM).
Where the water flow rate through the Baseray is not known, the ratings at the standard flow rate of 500 Lb./Hr. (1GPM)must be used.
Net AHRI Ratings are determined from tests made in accordance with the AHRI Testing and Rating Code for baseboard type radiation, including an allowance of
15% for heating effect permitted by the Code.
Maximum allowable working pressure - 30 PSI, water; 15 PSI, steam. Water content - 0.3 gal./lineal foot. For pressure drop information, see installation manual.
Ratings are based on active length. Active length equals total length.
NOTES:
Available in any length with similar sub-assemblies.
Maximum recommended length for steam: 10 Ft.
ASSEMBLY
LENGTH
L.H. CENTER
R.H.
6-1/2 Ft.
5-1/2 Ft. — 1 Ft.
7 Ft.
6 Ft. —
1 Ft.
7-1/2 Ft.
5-1/2 Ft. — 2 Ft.
8 Ft.
6 Ft. —
2 Ft.
8-1/2 Ft.
5-1/2 Ft. — 3 Ft.
9 Ft.
6 Ft. — 3 Ft.
9-1/2 Ft.
5-1/2 Ft. — 4 Ft.
10 Ft.
6 Ft. — 4 Ft.
10-1/2 Ft.
5-1/2 Ft. — 5 Ft.
11 Ft.
6 Ft. — 5 Ft.
11-1/2 Ft.
5-1/2 Ft. — 6 Ft.
12 Ft.
6 Ft. — 6 Ft.
12-1/2 Ft.
5-1/2 Ft. 6 Ft. 1 Ft.
13 Ft.
6 Ft. 6 Ft. 1 Ft.
ASSEMBLIES
18”
Left End
24”
Left End
24”
Int.
24”
Right End
12”
Right End
18”
Panel
24”
Panel
1-1/2 Ft. Assembly — — — — — 1 —
2 Ft. Assembly — — — — — — 1
2-1/2 Ft. Assembly 1 — — — 1 — —
3 Ft. Assembly — 1 — — 1 — —
3-1/2 Ft. Assembly 1 — — 1 — — —
4 Ft. Assembly — 1 — 1 — — —
4-1/2 Ft. Assembly 1 — 1 — 1 — —
5 Ft. Assembly — 1 1 — 1 — —
5-1/2 Ft. Assembly 1 — 1 1 — — —
6 Ft. Assembly — 1 1 1 — — —
SUB-ASSEMBLIES
5-1/2 Ft. L.H. Sub-Assembly 1 — 2 — — — —
6 Ft. L.H. Sub-Assembly — 1 2 — — — —
6 Ft. Center Sub-Assembly — — 3 — — — —
All R.H. Sub-Assemblies — — Req’d # 1 or 1 — —
BASERAY RATINGS Steam and Hot Water
BASERAY DIMENSIONS
Designed with performance and
dependability in mind, Baseray
Baseboards offer a sleek, low profile
design that will fit in well with
virtually any room decor. Unlike
most baseboards, Baseray can also
be painted, providing a seamless
match to its surroundings.
The simple, yet effective design of
the Baseray provides more than
five times the amount of radiant
heat to a room. This is due to the
fact that the cast iron surface area
is much larger than that found on
conventional thin metal baseboards,
and that heat can be distributed both
in horizontal AND vertical direction.
This leads to uniform, even heat
distribution in the room, and less
than a 2-degree difference between
floor and ceiling.
Each section of Baseray Baseboards
feature one-piece cast iron
construction. This design virtually
eliminates the expansion noises
created during heating cycles and
is built to last much longer than
conventional fabricated baseboards.
MODEL
NO.
APPROX WT
(lbs. Per Linear Foot)
FLOW
RATE
NET AHRI
STEAM RATING
NET AHRI WATER RATINGS BTUH Per Linear Foot At Average
Water Temperatures Indicated
9A 15
Lb./Hr. Sq. Ft.
BTU/Hr.
At 215°F
150°F 160°F 170°F 180°F 190°F 200°F 210°F 220°F 230°F
2000 3.40 860 340 390 450 510 560 610 670 720 770
500 3.40 860 320 370 430 480 530 580 630 680 730