BURR KING MFG. CO., INC 1220 Tamara Lane Warsaw, MO 65355 www.burrking.
BURR KING MFG. CO., INC. 1220 TAMARA LANE www.burrking.com WARSAW, MO 65355 (660) 438-8998 s (800) 621-2748 FAX (660) 438-8991 June, 2007 Burr King Manufacturing Company. Inc. warrants the below product to be free in material and workmanship. The period of warranty is 1 year (90 days for vibratory bowls of 20 quart and lesser volume) from the date of purchase.
BURR KING MFG. CO., INC. 1220 TAMARA LANE WARSAW MO 65355 WWW.BURRKING.COM (660) 438-8998 (800) 621-2748 FAX (660) 438-8991 August 29, 2007 LETTER OF AUTHENTICITY This letter is to certify that all Burr King Belt grinders, Disc grinders, Polishing machines Vibra King Chambers and Bowls are manufactured and assembled in the United States of America. (Tariff number 847990 criterion A) Don Mac Carthy President See our catalog at www.burrking.com contact us at info@burrking.
BURR KING MFG. CO., INC. 1220 TAMARA LANE WARSAW MO 65355 WWW.BURRKING.COM (660) 438-8998 (800) 621-2748 FAX (660) 438-8991 February 2005 OPERATOR, and OPERATING AREA SAFETY Subject equipment includes Grinders, buffers, polishers, and other rotating equipment. Serious injury or death may occur if minimum safety precautions are not understood, and obeyed by operators and those other persons who may be in the immediate vicinity of the subject equipment.
Continued from page 1 of the work rest (or table) will permit passage of the work piece through the gap (nip point). Note, however, that certain alloys such as titanium may create conditions where grinding debris can accumulate in a tight gap creating a potential fire hazard. When in doubt consult with your safety officer. Failure to observe this warning may result in the work piece or other item being caught in this gap, and/or being forcibly ejected.
Continued from page 2 Occupational Noise Exposure Burr King products produce levels of noise consistent with their intended purposes. The level and spectral content of noise produced is dependent on the product type, the degree that the product is maintained in proper operating condition, the abrasive/media and accessories used, the specific application, and the surrounding environment.
BURR KING MFG. CO., INC. 1220 TAMARA LANE WARSAW MO 65355 WWW.BURRKING.COM (660) 438-8998 (800) 621-2748 FAX (660) 438-8991 VibraKING 40 operating instructions ® November 2006 General description The VibraKING® 40 vibratory chamber uses commonly available abrasive or burnishing media to deburr, polish, de-scale, or otherwise surface condition parts made from various materials.
WARNING: Machines not anchored to the floor may “walk” while operating. Walking may occur with a light total load, if one or more of the machine feet are not in firm contact with the floor regardless of the load, or if the floor is not clean and free of debris, oil, or other materials that hinder the ability of the rubber machine feet pads to grip the floor. • • • Locate the machine conveniently. The floor should be firm and structurally sound; concrete is an ideal surface.
NOTICE: All variable speed models are equipped with a controller that incorporates the protective properties of a magnetic starter. NOTICE: All variable speed models use 3-phase motors regardless of incoming phase. In example a 220 volt, single-phase variable speed model uses a 2.0 horse power motor wired for 220 volts, 3 phase. If you are unsure about the installation of your machine, or its electrical configuration please consult with the Burr King factory.
create a fire/explosion hazard that could result in personal injury, or death. Use only clean water with recommended soaps. WARNING: Avoid eye damage, flesh burns, and/or poisoning. Many vibratory processing soaps, compounds, and media are acidic or caustic. Wear appropriate flesh, ear, and eye protection gear when using vibratory soaps and compounds, and when working around and with your VibraKING chamber. Do not ingest these materials.
For finer fluid control you must install a flow meter, most users find this unnecessary. If you elect to install a flow meter set the fluid flow between 1 and 8 gallons per hour as a starting point. To improve your parts surface condition post processing always rinse your parts in clean water shortly after removing them from the chamber, then dry them to minimize rusting. Remember that ferrous metals will oxide rapidly when machining, etc. expose fresh metal (as is the case with vibratory processing).
WARNING: Do not use flammable fluids or other materials in or near the Model 40 vibratory chamber. To do so may create danger to personnel, plant, and equipment due to fire or explosion. NOTICE: Unless specially ordered from the Burr King factory the VibraKING® 40 is not NEMA 4/4X rated for wet or wash-down operation. Authorized fluids required within the vibratory chamber enclosure for ordinary operation, and associated apparatus are not considered “wet or wash-down” application.
The media discharge chute is located on the lower portion of the machine right side. The chute plug may be removed by pulling it free of the tub after loosening the retaining clamp. With the machine operating, the media and parts (if smaller than the tube diameter) will cascade from the tube to a container of your choice. Maintenance of your Burr King Model 40 vibratory chamber Warning: NEVER open the machine service access panels without first removing electrical power.
ITEM NO. QTY. PART NO. 33 1 3518 34 1 3518-1 35 1 3518-2 36 2 3517 DESCRIPTION SCREEN, SEPERATOR - 1" SCREEN, SEPERATOR - 1/2" SCREEN, SEPERATOR - 1 3/8" TRAY, M40 33 34 35 36 3 TAMARA LANE WARSAW, MO. 65355 BURR KING STANDARD TOLERANCES X.X THE DATA CONTAINED HEREIN IS THE SOLE PROPERTY OF BURR KING MFG. CO., INC. REPRODUCTION OR DISTRIBUTION OF THIS DATA IS STRICTLY PROHIBITED WITHOUT CONSENT OF BURR KING MFG. CO., INC. A REV X.X X = 0.01 PRELIMINARY, NOT FOR PRODUCTION DESCRIPTION = 0.
ITEM NO. QTY. PART NO. DESCRIPTION 1 1 PLATFORM PLATFORM ASSEMBLY 2 1 DRIVE DRIVE ASSEMBLY 3 1 chamber CHAMBER ASSEMBLY 3 2 1 3 TAMARA LANE WARSAW, MO. 65355 BURR KING STANDARD TOLERANCES B THE DATA CONTAINED HEREIN IS THE SOLE PROPERTY OF BURR KING MFG. CO., INC. REPRODUCTION OR DISTRIBUTION OF THIS DATA IS STRICTLY PROHIBITED WITHOUT CONSENT OF BURR KING MFG. CO., INC. A REV REVISED TO SHOW OUTBOARD 10-04-02 PRELIMINARY, NOT FOR PRODUCTION 05-01-01 X.X X = 0.
ITEM NO. QTY. PART NO. 9 7 8 10 DESCRIPTION 1 1 4012-1 BASE, VIBRA KING 40 2 6 3314 FOOT, MACH. ISOLATOR, 68 SHORE 5 1 1-0005 BOLT, 3/8-16 x 3/4, HEX 6 1 5-0014 WASHER, LOCK 3/8, INTERNAL STAR 7 1 3527 PULLEY, 4.25 x 7/8 FIXED BORE 8 1 3-0001 SCREW, SET 3/8-16 x 1/2, BRASS TIP 9 1 1875-Key 3/16 SQ x 1 3/4 LG KEY 10 2 3511 GROMMET, RUBBER 7/8 ID x 3/16 14 1 1 MOTOR VARIOUS 15 shroud lid 10 1 15 14 2 3 TAMARA LANE WARSAW, MO.
ITEM NO. QTY. PART NO.
ITEM NO. QTY. PART NO. DESCRIPTION 1 1 3509 HOSE, LOW PRESS. 1 1/2 ID 2 1 3535 COUPLING, 1", SCH40 PVC 3 1 3536 BUSHING, 1x3/4 NPT, SCH40 PVC 4 1 3404 FITTING, BARBED, 3/4 NPT, NYLON 5 2 3510 CLAMP, HOSE 1" TO 3" SCREW DRIVE 5 1 5 2 3 4 3 TAMARA LANE WARSAW, MO. 65355 BURR KING STANDARD TOLERANCES X.X THE DATA CONTAINED HEREIN IS THE SOLE PROPERTY OF BURR KING MFG. CO., INC. REPRODUCTION OR DISTRIBUTION OF THIS DATA IS STRICTLY PROHIBITED WITHOUT CONSENT OF BURR KING MFG. CO., INC.
BURR KING 3 TAMARA LANE WARSAW, MO. 65355 M40 WATER INLET ITEM PART NUMBER NO. 1 3337 2 3338 3 3339 4 3549 5 3522 DESCRIPTION QTY.
Formulations Formula Color Purpose Polish Made of high alumina and contains no abrasives. Use with burnishing compounds to burnish metals or with loose abrasives or compounds for deburring. These pins produce a high luster finish and are suitable for use in all types of finishing equipment.
Burr King Mfg., Inc. PREFORMED TUMBLING 1220 Tamara Lane AND VIBRATORY Warsaw, MO 65355 (660) 438-8998 (800) 621-2748 CERAMIC ABRASIVES Fax:(660) 438-8991 Note: Green and Grey fields are in stock. Non stock items 500lb.
Preformed Tumbling & Vibratory Ceramic Abrasives Compositions P-60 = Light cut, superior finish, leaves clean surface, good for aluminum parts. (78-80lbs.) P-40 = Good cut and wear life, excellent finish, ideal for general purpose use, economical (89 to 90 lbs. per cubic foot) P-20 = Fastest cut, for heavy deburring, matte finish. (85 to 90 lbs.
