BURR KING MFG. CO., INC 1220 Tamara Lane Warsaw, MO 65355 www.burrking.
BURR KING MFG. CO., INC. 1220 TAMARA LANE WARSAW MO 65355 WWW.BURRKING.COM (660) 438-8998 (800) 621-2748 FAX (660) 438-8991 June, 2007 Burr King Manufacturing Company. Inc. warrants the below product to be free in material and workmanship. The period of warranty is 1 year (90 days for vibratory bowls of 20 quart and lesser volume) from the date of purchase.
BURR KING MFG. CO., INC. 1220 TAMARA LANE WARSAW MO 65355 WWW.BURRKING.COM (660) 438-8998 s (800) 621-2748 FAX (660) 438-8991 June 21, 2007 LETTER OF AUTHENTICITY This letter is to certify that all Burr King Belt grinders, Disc grinders, Polishing machines Vibra King Chambers and Bowls are manufactured and assembled in the United States of America. (Tariff number 847990 criterion A) Don Mac Carthy President See our catalog at www.burrking.com contact us at info@burrking.
BURR KING MFG. CO., INC. 1220 TAMARA LANE WARSAW MO 65355 WWW.BURRKING.CO M (660) 438-8998 s (800) 621-2748 FAX (660) 438-8991 February 2005 OPERATOR, and OPERATING AREA SAFETY Subject equipment includes Grinders, buffers, polishers, and other rotating equipment. Serious injury or death may occur if minimum safety precautions are not understood, and obeyed by operators and those other persons who may be in the immediate vicinity of the subject equipment.
Continued from page 1 of the work rest (or table) will permit passage of the work piece through the gap (nip point). Note, however, that certain alloys such as titanium may create conditions where grinding debris can accumulate in a tight gap creating a potential fire hazard. When in doubt consult with your safety officer. Failure to observe this warning may result in the work piece or other item being caught in this gap, and/or being forcibly ejected.
Continued from page 2 Occupational Noise Exposure Burr King products produce levels of noise consistent with their intended purposes. The level and spectral content of noise produced is dependent on the product type, the degree that the product is maintained in proper operating condition, the abrasive/media and accessories used, the specific application, and the surrounding environment.
BURR KING MFG. CO., INC. 1220 TAMARA LANE WARSAW MO 65355 WWW.BURRKING.COM (660) 438-8998 (800) 621-2748 FAX (660) 438-8991 November 2004 Operating instructions for Models 150SX and 200SX VibraKING enhanced performance vibratory bowls ® The VibraKING 150SX and 200SX enhanced performance vibratory bowls are bench top, or stand mounted vibratory processing machines. The bowls are compatible with ceramic, plastic, shell, cob, and most other media types.
Avoid electrocution hazards. The 150SX and 200SX bowls are not NEMA 4 or NEMA 4X rated. They must not be used in a manner that allows fluids to enter the unit base, power cord, on/off switch, or electrical plug. Avoid fire and explosion hazards. The use of fluids other than water and Burr King specified soaps in the bowl (or any associated fluid re-circulating system) may create a fire/explosion hazard that could result in personal injury, or death.
• • Loosen the setscrew on the bottom weight only. If the vibratory amplitude was to little rotate the bottom weight so that it is in closer alignment (more concentric) with the upper weight. If the vibratory amplitude was to great rotate the bottom weight such that it is lesser alignment (less concentric) with the upper weight and re-tighten the setscrew. Maximum vibratory amplitude occurs when the two weights are exactly concentric with each other.
• • • • Media and compounds of many descriptions. FilterPAK® 4000 filtration systems with integrated fluid pump, filter, and fluid reservoir. StandPAK® 5000 vibratory base with integrated process timer, bowl mount surface, power distribution panel, and integrated receiver for the FilterPAK® 4000. Spare bowls, and replacement parts. Occupational Noise Exposure Burr King vibratory bowls produce levels of noise consistent with their intended purposes.
Formulations Formula Color Purpose Polish Made of high alumina and contains no abrasives. Use with burnishing compounds to burnish metals or with loose abrasives or compounds for deburring. These pins produce a high luster finish and are suitable for use in all types of finishing equipment.
Burr King Mfg., Inc. PREFORMED TUMBLING 1220 Tamara Lane AND VIBRATORY Warsaw, MO 65355 (660) 438-8998 (800) 621-2748 CERAMIC ABRASIVES Fax:(660) 438-8991 Note: Green and Grey fields are in stock. Non stock items 500lb.
Preformed Tumbling & Vibratory Ceramic Abrasives Compositions P-60 = Light cut, superior finish, leaves clean surface, good for aluminum parts. (78-80lbs.) P-40 = Good cut and wear life, excellent finish, ideal for general purpose use, economical (89 to 90 lbs. per cubic foot) P-20 = Fastest cut, for heavy deburring, matte finish. (85 to 90 lbs.
