BURR KING MFG. CO., INC MODEL 562 INSTRUCTION MANUAL 1220 Tamara Lane Warsaw, MO 65355 www.burrking.
BURR KING MFG. CO., INC. 1220 TAMARA LANE WARSAW MO 65355 WWW.BURRKING.COM (660) 438-8998 (800) 621-2748 FAX (660) 438-8991 June, 2007 Burr King Manufacturing Company. Inc. warrants the below product to be free in material and workmanship. The period of warranty is 1 year (90 days for vibratory bowls of 20 quart and lesser volume) from the date of purchase.
BURR KING MFG. CO., INC. 1220 TAMARA LANE WARSAW MO 65355 WWW.BURRKING.COM (660) 438-8998 (800) 621-2748 FAX (660) 438-8991 August 29, 2007 LETTER OF AUTHENTICITY This letter is to certify that all Burr King Belt grinders, Disc grinders, Polishing machines Vibra King Chambers and Bowls are manufactured and assembled in the United States of America. (Tariff number 847990 criterion A) Don Mac Carthy President See our catalog at www.burrking.com contact us at info@burrking.
BURR KING MFG. CO., INC. 1220 TAMARA LANE WARSAW MO 65355 WWW.BURRKING.COM (660) 438-8998 (800) 621-2748 FAX (660) 438-8991 February 2005 OPERATOR, and OPERATING AREA SAFETY Subject equipment includes Grinders, buffers, polishers, and other rotating equipment. Serious injury or death may occur if minimum safety precautions are not understood, and obeyed by operators and those other persons who may be in the immediate vicinity of the subject equipment.
Continued from page 1 of the work rest (or table) will permit passage of the work piece through the gap (nip point). Note, however, that certain alloys such as titanium may create conditions where grinding debris can accumulate in a tight gap creating a potential fire hazard. When in doubt consult with your safety officer. Failure to observe this warning may result in the work piece or other item being caught in this gap, and/or being forcibly ejected.
Continued from page 2 Occupational Noise Exposure Burr King products produce levels of noise consistent with their intended purposes. The level and spectral content of noise produced is dependent on the product type, the degree that the product is maintained in proper operating condition, the abrasive/media and accessories used, the specific application, and the surrounding environment.
BURR KING MFG. CO., INC. 1220 TAMARA LANE WARSAW MO 65355 WWW.BURRKING.COM (660) 438-8998 (800) 621-2748 FAX (660) 438-8991 June 2007 Operating instructions for the Model 562 belt grinder The model 562 belt grinder is a three wheel path belt grinder that use a 1 x 42 inch continuous loop abrasive belt. For maximum effectiveness, and operator safety use abrasive belts manufactured by well respected abrasive manufacturers. * Use abrasive belts that are the proper size and type for your machine.
. Prior to operating the model 562 read the Operator, and Operating Area Safety Instructions carefully. Insure that all persons who will operate the model 562, or who will work in the vicinity of the model 562 read, understand, and comply with these instructions. 9. Insure that the grinder is located in an area that provides clear access to the machine such that operators have clear and unobstructed access to the machine.
Maintenance for the model 562 FIRST DISCONNECT THE MACHINE FROM ITS AC POWER SOURCE. * Every thirty days apply light machine oil to the rear wheel support (P/N 435) to rear wheel handle (P/N 537G) interface. Two drops of oil is sufficient. * Every thirty days check the v-belt (P/N 429) tension. If you can hear the belt “slap” the vbelt guard (P/N 428) when the drive motor starts, the v-belt may require re-tensioning.
02'(/ %855 .
,7(0 12 3$57 180%(5 $ 02725 % $ ) % F $ & / '(6&5,37,21 %$6( 0$&+,1( )5$0( :$6+(5 6$( =,1& 3/7' %2/7 [ +(; +($' 678' *8$5' 9 %(/7 %(/7 9 '5,9( 38//(< 38//(< *8$5' 9 %(/7 :$6+(5 $1 187 -$0 3/7' &
MAG STARTER BURR KING PARTS LIST 1220 TAMARA LANE WARSAW, MO.
BURR KING 1220 TAMARA LANE WARSAW, MO. 65355 ITEM NO. 1 2 3 4 5 6 7 8 9 10 11 MAG STARTER PART NUMBER DESCRIPTION MB-4C BRACKET, MOUNTING, STARTER MOTOR CALL FACTORY FOR PART NUMBER 4 WASHER, 5/16 SAE ZINC PLTD 37 BOLT, 5/16-18x3/4 HEX HEAD 5 WASHER, 1/4 AN 209 SCREW, 1/4-20 X 3/4 ALLEN HEAD 4-0013 NUT, KEP, 1/4-20 MS2A3 3/4HP-1HP, 220V MS4A3 3/4HP-1HP, 440V MS2B3 1.5HP-3HP, 220V MS4B3 1.5HP-3HP, 440V 775 CONNECTOR, 3/8", STR, LIQ. TIGHT 776 CONNECTOR, 3/8", 90 DEG, LIQ.
VARI SPEED BURR KING SINGLE PHASE 1220 TAMARA LANE WARSAW, MO. 65355 3/4-1 HP 1.
ITEM NO. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 VARI SPEED PART NUMBER MB-4C 941-3 5-0032 4 209 5 4-0013 100B-1725C 150B-1725C 37 015-1 017 020 864-1 775 776 643 862-3 DESCRIPTION BRACKET, MOUNTING, STARTER BRACE, MB4 SUPPORT WASHER, 1/4, LOCK, SPLIT, PLTD WASHER, 5/16 SAE ZINC PLTD SCREW, 1/4-20 X 3/4 ALLEN HEAD WASHER, 1/4 AN NUT, KEP, 1/4-20 1 HP MOTOR 1.5 HP MOTOR BOLT, 5/16-18x3/4 HEX HEAD 120V CORD 220V CORD CONDUIT 3/8" LIQUIDTIGHT CONT. 115/220V 0.75-1HP CONNECTOR, 3/8" STR, LIQ.
562 BURR KING LINE DRAWING 11.35 0.45 0.45 17.9 8.85 0.375 TOP VIEW 6.175 MOUNTING PATTERN 20 17.9 5 12.25 FRONT VIEW 9.75 RIGHT SIDE VIEW 1220 TAMARA LANE WARSAW, MO.