Instruction Manual 1 Instruction Manual Dear Customer, Thank you for choosing a ERIBA caravan. This instruction manual is intended to help you get to know and use your new caravan. It is essential that you read and comply with the safety instructions in chapter 2. Don’t hesitate to contact our ERIBA service centres if you have any questions. Their staff are fully conversant with your vehicle and will be pleased to help in any way they can. Our list of ERIBA service centres in Europe is updated regularly.
Instruction Manual Touring - 03/11-1 - englisch (EN) - 0731070 - HYW-0102-01EN
Guarantee Notification of delivery Customer Address Surname, Christian Name: Street, No.: Postal Code, Town: Country: To be completed on the date the vehicles is handed-over by the selling dealer, a copy being returned to HYMER AG. Vehicle Data Model: Version No.: Serial Number: Chassis Number: Initial Registration: Confirmation: I have today received the Service Coupon Book for the annual servicing intervals and the water ingress test for the stated model.
Guarantee Water Ingress Test * During the water ingress test, your ERIBA dealer or an authorised workshop, using a hygrometer, checks the entire body of your vehicle for water impermeability. The test is carried out on all connections, windows, skylights, external flaps and doors. Important: The six-year weatherproof guarantee is only valid when the testing intervals are upheld. The water ingress test must be carried out on an annual basis. The water ingress test may be carried out max.
Guarantee 3. Any leak covered by the guarantee, will be remedied by the authorised ERIBA dealer. Should the remedy not succeed and the party covered by the guarantee cannot be reasonably expected to accept additional guarantees provided by the ERIBA dealer, then the party covered by the guarantee can have the leakage remedied by HYMER AG, at the expense of the ERIBA dealer. No further claims apply. 4.
Guarantee Service Proof for a Motorhome or Caravan Inspection 1 Water Ingress Test 1 12 months after taking delivery or 7,500 km, depending on which comes first. Water Ingress Test: Paste in the customer service stamp for the 12 month check here (subject to payment).
Guarantee Service Proof for a Motorhome or Caravan Inspection 3 Water Ingress Test 3 Every 12 months or after 25,000 km - depending on which comes first. Water Ingress Test: Paste in the customer service stamp for the 12 month check here (subject to payment). Date: Mileage Reading: 36 Months Dealer’s Signature and Stamp: Should it be determined during a vehicle check that additional work is necessary, then the carrying out of this work is dependent on the customer commissioning this to be done.
Guarantee Service Proof for a Motorhome or Caravan Inspection 5 Water Ingress Test 5 Every 12 months or after 45,000 km - depending on which comes first. Water Ingress Test: Paste in the customer service stamp for the 12 month check here (subject to payment). Date: Mileage Reading: 60 Months Dealer’s Signature and Stamp: Should it be determined during a vehicle check that additional work is necessary, then the carrying out of this work is dependent on the customer commissioning this to be done.
Guarantee Service Proof for a Motorhome or Caravan Inspection 8 Inspection 9 Every 12 months or after 75,000 km - depending on which comes first. Every 12 months or after 85,000 km - depending on which comes first. Date: Date: Mileage Reading: Mileage Reading: Dealer’s Signature and Stamp: Dealer’s Signature and Stamp: Should it be determined during a vehicle check that additional work is necessary, then the carrying out of this work is dependent on the customer commissioning this to be done.
Guarantee 10 Touring - 03/11-1 - englisch (EN) - 0731070 - HYW-0102-01EN
Contents 0 1 1.1 1.2 Introduction . . . . . . . . . . . . . . . . . 17 General . . . . . . . . . . . . . . . . . . . . . 18 Environmental Tips . . . . . . . . . . . . 18 2 2.1 2.1.1 2.1.2 2.1.3 2.2 2.3 2.4 2.5 2.6 2.7 Safety . . . . . . . . . . . . . . . . . . . . . . Fire Prevention . . . . . . . . . . . . . . . Avoidance of Fire Risks . . . . . . . . . Fire-Fighting . . . . . . . . . . . . . . . . . In Case of Fire . . . . . . . . . . . . . . . . General . . . . . . . . . . . . . . . . . . . . .
0 Contents 8.5 8.6 8.6.1 8.6.2 8.6.3 8.7 8.8 8.8.1 8.8.2 8.8.3 8.9 8.9.1 8.9.2 8.10 8.11 8.12 9 9.1 9.2 9.2.1 9.2.2 9.2.3 9.2.4 9.3 9.4 9.4.1 9.4.2 9.5 9.5.1 9.6 9.6.1 9.6.2 9.6.3 10 10.1 10.2 10.3 10.3.1 10.3.2 12 Energy Reserve of the Living Area Battery . . . . . . . . . . . . Charging the Living Area Battery (Power Pack SE) . . . . . . . . . . . . . . Charging Using a 240 V Power Supply . . . . . . . . . . . . . . . . . . . . . . Charging Using the Vehicle Engine of the Towing Vehicle . . . .
Contents 0 13 13.1 13.2 13.3 13.4 13.5 13.5.1 13.5.2 13.5.3 13.6 14 14.1 14.2 14.3 14.4 14.5 14.6 14.6.1 14.6.2 14.6.3 14.7 14.8 15 15.1 16 16.1 Technical Data . . . . . . . . . . . . . . 141 Technical Data . . . . . . . . . . . . . . 141 17 17.1 17.8 17.9 Helpful Notes . . . . . . . . . . . . . . . Traffic Rules in Foreign Countries . . . . . . . . . . . . . . . . . . . Help on Europe’s Roads . . . . . . . Speed Limits . . . . . . . . . . . . . . . . Driving with Low Beam in European Countries . . . .
0 Contents 14 Touring - 03/11-1 - englisch (EN) - 0731070 - HYW-0102-01EN
Check List Before First Journey of the Vehicle 0 Observe following instructions before first journey of the vehicle: 5 Check List Before First Journey of the Vehicle Re-tighten wheel bolts after 50 km (30 miles). Read the instruction manual to avoid personal and material damage. Observe following instructions before each journey of the vehicle: Check the tyre pressures. See section Tyre Pressure. Load the vehicle correctly. Observe the maximum permissible gross weight. See section Payload.
0 Check List Before First Journey of the Vehicle 16 Touring - 03/11-1 - englisch (EN) - 0731070 - HYW-0102-01EN
Introduction 1 Please read this instruction manual completely before using the vehicle for the first time! 1 Introduction Always keep this instruction manual in the caravan. Also inform all other users of the safety regulations. The non-observance of this symbol can lead to personal injury. > The non-observance of this symbol can lead to damage being caused to, or inside the vehicle. > This symbol indicates recommendations or special aspects.
1 Introduction 1.1 General The caravan is constructed in accordance with the latest state of technology and the recognised safety regulations. Nevertheless, personal injury may result and the caravan may be damaged if the safety instructions in this instruction manual are not followed. Only use the caravan in a technically impeccable condition. Follow the instructions in the instruction manual.
Safety 2 Chapter Overview 2 Safety This chapter contains important safety instructions. The safety instructions are for the protection of persons and property. The instructions address the following topics: l fire prevention and what to do in case of fire l general care of the caravan l road safety of the caravan l gas fittings of the caravan l electrical fittings of the caravan l water system of the caravan 2.1 Fire Prevention 2.1.1 Avoidance of Fire Risks 2.1.
2 Safety 2.2 General Ensure that there is sufficient ventilation. When staying in the caravan, open the lifting roof. There is a danger of suffocation due to increased CO2 levels. Observe the headroom of the conversion door. > As far as the appliances (gas heater, cooker, refrigerator, etc.) are concerned, the instruction manuals are authoritative. It is imperative that they be observed! > Fitting accessories or special equipment can alter the dimensions, weight and road behaviour of the caravan.
Safety 2 2.3 Roadworthiness Before commencing the journey, check the brakes and the indicating and lighting equipment. After the vehicle has been standing for a longer period (approx. 10 months) have the braking and gas systems checked by an authorised specialist workshop. During the journey, no persons are to travel inside the caravan. In winter, the roof must be free of snow and ice prior to the commencement of the journey. Before commencing the journey, empty the waste water tank.
2 Safety 2.4 Towing Care is to be taken when connecting and detaching the caravan. No persons are to be between the towing vehicle and the caravan during positioning for connecting and detaching. 2.5 Gas Fittings Before commencing the journey, close all gas isolator taps and the regulator tap. Have the gas fittings repaired or altered by an authorised workshop only. Have the gas fittings checked by an authorised specialist workshop according to the national regulations before commissioning.
Safety 2 Propane gas is capable of gasification up to -42 °C, whereas butane gas gasifies at 0 °C. Below these temperatures no gas pressure is available. Butane gas is unsuitable for use in winter. Inspect the gas tube fitted to the gas bottle connection for tightness. The gas tube should have no tears and should not be porous. It is recommended that the gas tube be replaced every 12 months, or earlier if necessary.
2 Safety 24 Touring - 03/11-1 - englisch (EN) - 0731070 - HYW-0102-01EN
Before the Journey 3 Chapter Overview 3 Before the Journey This chapter contains important instructions which should be noted before beginning commencing your journey or carrying out any tasks before the journey.
3 Before the Journey > Ensure that the interior of the coupling is not soiled and that the movable parts of the coupling (not the ball retainer) are lubricated. > AKS stabiliser: The tow ball is not to be lubricated when using the stabiliser. The friction pads are pressed against the coupling ball and thereby generate an anti-rolling moment. This anti-rolling effect is only guaranteed when the towing vehicle coupling head is free of lubricant and other residues.
Before the Journey 3 3.3 Caravan Couplings > Before connecting, ensure that the ball head of the coupling device is free of dirt and grease. 3.3.1 AL-KO AK 160 The coupling mechanism has an "Open position". As long as the caravan coupling is not placed on top of the implement coupling, the coupling handle remains open. 1 2 n Place the open caravan coupling (Fig. 1) on the towing vehicle caravan ball. The caravan coupling now locks automatically and audibly in place.
3 Before the Journey 3.3.2 AL-KO AKS 1300 n Pull up the stabilising lever (Fig. 2,1) as far 3 5 as possible. n Turn the handwheel (Fig. 2,2) in an anti- 1 clockwise direction as far as possible in the open position. 2 n Pull the coupling handle (Fig. 2,3) upwards. n Place the opened stabiliser on the caravan 4 ball. The coupling handle must audibly lock back into its previous position. 1 n In addition, push the coupling handle downwards with your hand.
Before the Journey 3 3.5 Payload > The maximum permissible gross weight stated in the vehicle documents is not to be exceeded by the payload. > Excessive payload and wrong tyre pressure can cause tyre burst. You can lose the control over the caravan. > Built-in accessories and special equipment reduce the payload. > Adhere to the axle load stated in the vehicle documents. Load the caravan so that the drawbar coupling head is not pushed downwards due to the permissible nose weight.
3 Before the Journey (2) Mass in a ready-to-drive condition The mass in ready-to-drive condition is made up as follows: - Unladen weight (mass of the empty vehicle) with factory-installed standard equipment - Basic equipment Basic equipment includes all equipment and fluids required for safe and proper vehicle use.
Before the Journey 3 (3.2) Personal equipment Personal equipment includes all items in the caravan which do not appear in the list above.
3 Before the Journey 3.5.2 Loading the Caravan Correctly Evenly distribute the payload on the left-hand and right-hand side of the caravan. Store heavy objects (awning, tin cans, etc.) close to the axles so that they cannot slip, e. g. - in low-lying storage compartments, the doors of which do not open in the direction of travel - on the floor Store lighter objects (laundry) in the roof storage compartments. For safety reasons, weigh the loaded caravan before commencing the journey.
Before the Journey 3 3.5.3 Caravan Load, Nose Weight and Axle Load > The information on the towing ve- hicle documents is important for the selection of the car and caravan. 2 1 The caravan load (Fig. 5,1) stipulated in the 3 towing vehicle documents provides information as to the maximum weight which the towing vehicle is permitted to tow. The caravan load refers to the actual weight of the caravan and not HYW02770 to the maximum permissible gross weight of the Fig.
3 Before the Journey 3.6 Entrance Step Before commencing the journey, check whether the entrance step is completely pushed in. > Do not grease or lubricate the pivot bearing and joints of the entrance step (see chapter 11). Pushing in or pulling out Pulling out: n Hold of the bottom of the entrance step (Fig. 6,1) pull out and fold down. Pushing in: n Hold of bottom of the entrance step, lift the front and push it backwards. Fig.
Before the Journey 3 3.7 Roadworthiness Before commencing the journey, work through the check list: No.
3 Before the Journey 36 Touring - 03/11-1 - englisch (EN) - 0731070 - HYW-0102-01EN
During the Journey 4 Chapter Overview 4 During the Journey This chapter contains instructions on how to drive the caravan. The instructions address the following topics: l driving speed l brakes 4.1 Driving with the Caravan During the journey, no persons are to travel inside the caravan. The caravans are designed by HYMER AG for a technically permissible maximum speed of 100 km/h (60 mph). Therefore never drive faster than 100 km/h (60 mph).
4 During the Journey 38 Touring - 03/11-1 - englisch (EN) - 0731070 - HYW-0102-01EN
Pitching the Caravan 5 Chapter Overview 5 Pitching the Caravan This chapter contains instructions on how to pitch the caravan. The instructions address the following topics: l handbrake l wheel chocks l driving in reverse l operation of the corner steadies l opening and closing the external doors and flaps l 240 V external connection > Pitch the caravan so that it is as horizontal as possible. 5.1 Handbrake n Apply the handbrake (Fig. 7,1) when park- ing the caravan. It locks automatically in place.
5 Pitching the Caravan 5.3 Driving in Reverse As far as all models with an automatic reverse driving mechanism are concerned, the caravan can be reversed without difficulty. In addition to the rolling resistance, residual braking power must be taken into account. 5.4 Corner Steadies > Do not use the corner steadies, fitted to the caravan as standard, as a vehicle jack. The corner steadies are only for stabilising the pitched caravan. The caravan wheels are not to be raised above the ground.
Pitching the Caravan 5 5.5 Conversion Door Only drive with a locked conversion door. > When leaving the caravan, close the conversion door. > Always return the locking cylinder to its initial position. 5.5.1 Conversion Door, Outside Opening when the conversion door is locked: n Insert the key into locking cylinder and turn in a clockwise direction (Fig. 10,1) until the lock is unlatched. n Return the key to the central position (Fig. 10,2) and remove it.
5 Pitching the Caravan 5.5.2 Conversion Door, Inside Opening: n Turn the knob in an anticlockwise direction (Fig. 12,1). Locking: n Turn the door knob approx. 45° in a clock- wise direction and leave in this position (Fig. 12,2 and Fig. 13). 5.5.3 Fig. 12 Door lock of conversion door, inside, open Fig. 13 Door lock of conversion door, inside, closed Fig.
Pitching the Caravan 5 5.6 External Flaps > Before commencing the journey, close all external flaps and lock them. > When leaving the caravan, close all external flaps. > Always return the locking cylinder to the initial position. The external flaps fitted to the caravan are all fitted with unified locking cylinders. Therefore, all locks can be opened with a single key. 5.6.1 Flap Lock for External Flaps (Variant 1) > During rain, water can penetrate the opened flap lock.
5 Pitching the Caravan 5.6.2 Flap Lock for External Flaps (Variant 2) > During rain, water can penetrate the opened flap lock. Therefore close the lock handle (Fig. 16,2) as shown in Fig. 16. Opening: n Insert key into locking cylinder (Fig. 16,1) and turn a quarter turn in an anticlockwise direction. The lock handle (Fig. 16,2) snaps out. n Turn lock handle one quarter turn in an anticlockwise direction. The flap lock is open. n Return the key to the central position and remove it.
Pitching the Caravan 5 5.6.3 Flap Lock for External Flaps (Variant 3) Opening: n Insert key into locking cylinder (Fig. 17,1) of the push-button lock and turn a quarter turn in an anticlockwise direction. n Press both push-button locks simultaneous- ly with your thumbs and open the external flap. Closing: n Close the external flap and press it shut. n Insert key into locking cylinder (Fig. 17,1) Fig. 17 Flap lock (variant 3) and turn a quarter turn in a clockwise direction.
5 Pitching the Caravan 46 Touring - 03/11-1 - englisch (EN) - 0731070 - HYW-0102-01EN
Living 6 Chapter Overview 6 Living This chapter contains instructions about living in the caravan. The instructions address the following topics: l heating the caravan l ventilation of the caravan l opening and closing the hinged windows l opening and closing the lifting roof l modifying the table surfaces l removing tables l extending the seating group (Troll) l use of the beds 6.1 Heating During heater operation, the exhaust gas pipe in the wardrobe will get hot.
6 Living 6.3 Windows > The windows are fitted with a blind and an insect screen. After the latch has been released, the blind and insect screen automatically spring back to the initial position by tensile force. In order not to damage the tension mechanics, hold onto the blind or insect screen and allow it to slowly return to the initial position. > Before commencing the journey, always close the windows. > Depending on the weather, close the windows far enough to prevent moisture from entering.
Living 6 Opening hinged window with clamp fitting: n Place window handle (Fig. 18,3) into a vertical position. n Open the hinged window until the required position has been reached and use knurled knob (Fig. 19,1) to secure in position. Closing hinged window with clamp fitting: n Turn knurled knob (Fig. 19,1) until the latch is released. n Close the hinged window. n Place the window handle (Fig. 18,3) into a horizontal position. The locking catch (Fig.
6 Living Continuous ventilation: Using the window handles, the hinged window can be placed in two different positions: - Continuous ventilation (Fig. 21) or - firmly closed (Fig. 18). To place the hinged window into the "continuous ventilation" position: n Open window handle (Fig. 21,3) of the hinged window. n Lightly open the hinged window outwards. n Return window handle into its original posi- tion. The locking catch (Fig. 21,2) has to be moved into the recess of window catch (Fig. 21,1). Fig.
Living 6 6.3.2 Blind and Insect Screen The windows in the caravan are fitted with a blind and an insect screen. The blind and insect screen can be adjusted separately. Blind and insect screen are located in the top blind box. Blind Closing: n Pull blind at the handle (Fig. 22,2) down- wards. If the blind is to be completely closed, it is suspended into the locking devices (Fig. 22,3) situated on both sides of the window frame. Fig.
6 Living 6.4 Lifting Roof The apertures for forced ventilation must always be kept open. Never cover or block forced ventilations with objects as e. g. a winter mat. Keep forced ventilations clear of snow and leaves. When staying in the caravan, the lifting roof must be opened. > Before closing the lifting roof, always close the ventilation zips. > Ensure that the canvas is not trapped between the lifting roof and the vehicle roof. > Before commencing the journey, always close the lifting roof.
Living 6 6.5 Tables 6.5.1 Fixed Table Round Seating Group The top of the fixed table of the round seating group can be moved both lengthways and crossways. In addition, the top can be rotated. Rotating table-top: n Undo the knurled screw (Fig. 24,1). n Rotate the table-top (Fig. 24,2) into the desired position. n Retighten the knurled screw. Moving table-top lengthways or crossways: n Undo the knurled screw (Fig. 24,1). n Undo the knurled screws (Fig. 24,3). n Rotate the table-top (Fig.
6 Living 6.5.2 Folding Table Single Bed Seating Group Troll (Variant 1) > Before commencing the journey, always retract the folding table and secure it in the holder provided for this purpose. Putting up folding table: n Undo the snap fasteners of the securing straps (Fig. 25,2). n Open retaining belt (Fig. 25,1). n Carefully remove the folding (Fig. 25,3) from the holder. table n Place the folding table with the legs upwards onto the seat cushions. n Fold the legs (Fig.
Living 6 6.5.3 Folding Table Single Bed Seating Group Troll (Variant 2) The variant 2 of the folding table can be also used as a table extension of the variant 1. n Pull the complete cover plate of the bedside locker (Fig. 27,2) forwards. n Fold the upper part of the cover plate (Fig. 27,1) backwards (Fig. 27). 6.6 Fig. 27 Folding table, bedside locker Fig. 28 Seating group after extending Extending the Troll Single Bed Seating Group n Place folding table to the side.
6 Living 6.7 Beds 6.7.1 Bunk Bed Maximum loading of the bunk bed 50 kg. Never allow small children to remain in the bunk bed without supervision. But in particular with regard to small children less than three years of age, users should ensure that they cannot fall out of the bunk bed. Use separate children’s beds or travel cots suitable for children. Depending on the model, the caravan is fitted with a bunk bed. The bunk bed can be used immediately, without additional conversion.
Living 6 6.7.3 Fixed Bed (Variant 1) A storage compartment is underneath the bed. Lift up the slatted frame to place items in the storage compartment or to empty it. Opening: n Lift the mattress forwards and set it down on the panel. n Lift slatted frame. The gas-pressure springs (Fig. 30,1) hold the slatted frame open. Closing: Fig. 30 Fixed bed (variant 1) Fig. 31 Fixed bed (variant 2) n Press the slatted frame downwards against the resistance of the gas-pressure spring.
6 Living 6.8 Sleeping Conversion 6.8.1 Front Seating Group n Place the seat cushions (Fig. 32,2) in an up- 4 1 3 2 2 1 1 right position. 8 n Slightly lift the front of the table-top 2 7 5 6 (Fig. 32,3). n Release the locking device fitted to the table leg and fold the lower half of the table leg backwards by 90°. 3 4 8 HYW02561 Fig. 32 Prior to conversion n Lift the table-top (Fig. 32,3) by approx. 45°, remove it out of the upper mounting rail (Fig.
Living 6 n Place the back cushions (Fig. 35,1) between the two seat cushions (Fig. 35,2). n Depending on the model, place the additional cushion (Fig. 35,9) on top. Fig. 35 After conversion (not for Troll 530) Fig.
6 Living 6.8.2 Side Seating Group Troll 552 GT/Front Seating Group Troll 550/555 GT 5 4 3 1 2 5 4 1 3 2 n Slightly lift the front of the table-top (Fig. 37,3). n Release the locking device fitted to the table 6 6 leg and fold the lower half of the table leg backwards by 90°. n Lift the table-top by approx. 45°, remove it 7 7 HYW06805 Fig. 37 Prior to conversion 54 7 3 out of the mounting rail and place to the side. n Lay the two seat cushions in position (Fig. 37,2 and 4).
Living 6 6.8.3 Seating Group with two Single Beds n Slightly lift the front of the table-top (Fig. 40,3). 4 1 2 3 2 5 1 3 2 n Press the top of the table leg together and 7 fold it against the bottom of the table. 26 5 7 n Lift the table-top (Fig. 40,3) by approx. 45°, remove it out of the mounting rail (Fig. 40,4) and place to the side. The table is not required for the sleeping conversion. HYW06697 Fig. 40 Prior to conversion n Pull out slatted frame (Fig. 41,7).
6 Living 6.8.4 Seating Group with Bed 1400 x 1900 n Slightly lift the front of the table-top (Fig. 43,3). 4 1 2 2 3 1 1 2 3 2 1 n Press the top of the table leg (Fig. 43,6) together and fold it against the bottom of the table. n Lift the table-top by approx. 45°, remove it out of the mounting rail (Fig. 43,4) and place to the side. The table is not required for the sleeping conversion. 6 7 5 5 HYW00711 Fig. 43 Prior to conversion 2 2 n Release bed leg (Fig.
Living 6 6.8.5 Seating Group Puck 120 n Slightly lift the front of the table-top (Fig. 46,3). n Remove table leg (Fig. 46,6). n Lift the table-top by approx. 45°, remove it out of the mounting rail (Fig. 46,4) and lay it aside. The table is not required for the sleeping conversion. Fig. 46 Prior to conversion Fig. 47 During conversion Fig. 48 After conversion n Remove the bed rods (Fig. 47,7) from the bedding box (Fig. 47,5). n Lift up both seat cushions (Fig. 47,2) and place the two bed rods (Fig.
6 Living 6.8.6 Seating Group Puck L 225 GT n Slightly lift the front of the table-top (Fig. 49,3). n Press the top of the table leg (Fig. 49,6) together and fold it against the bottom of the table. n Lift the table-top by approx. 45°, remove it out of the mounting rail (Fig. 49,4) and lay it aside. The table is not required for the sleeping conversion. Fig. 49 Prior to conversion Fig. 50 During conversion Fig. 51 After conversion n Remove the bed rods (Fig. 50,7) from the bedding box (Fig. 50,5).
Living 6 6.8.7 Use of Bed Extension (Depending on Model) 1 n Release bedding box front wall (Fig. 52,4) from the locking device. 2 4 3 HYW00741 Fig. 52 Prior to conversion n Tilt bedding box front wall in the direction of the floor. 5 1 n Lift bedding box extension (Fig. 53,5). 2 4 3 HYW00801 Fig. 53 During conversion n Allow the bedding box extension (Fig. 54,5) to engage and, if necessary, lift the seat cushion. 5 1 n Use the additional cushion for sleeping con- 2 version.
6 Living 66 Touring - 03/11-1 - englisch (EN) - 0731070 - HYW-0102-01EN
Gas Fittings 7 Chapter Overview 7 Gas Fittings This chapter contains instructions regarding the gas fittings of the caravan. The instructions address the following topics: l safety l changing the gas bottles l gas isolator taps l external gas connection The operation of the gas operation appliances of the caravan is described in chapter 9. 7.1 General Before commencing the journey, close all gas isolator taps and the regulator tap.
7 Gas Fittings Due to its function and construction, the gas bottle compartment is a space which is open to the exterior. In order to enable leaking gas to immediately be dispersed outside, the standard forced ventilation is never to be blocked or covered. Do not use the gas bottle compartment for storage. Lock the gas bottle compartment in order to prevent unauthorised persons opening it. The regulator tap on the gas bottle must be accessible. Only connect gas-operated devices (e. g.
Gas Fittings 7 7.3 Changing Gas Bottles When you have changed the gas bottle, check whether gas escapes at the connection points and unions. Use a leakage search spray to spray the relevant connection point or union (ERIBA accessories shop). n Close regulator tap (Fig. 55,1) on the gas bottle (Fig. 55,4). Pay attention to the direction of the arrow. n Unscrew the gas pressure regulator (Fig. 55,3) with the gas tube (Fig. 55,5) from the gas bottle with a suitable gas spanner.
7 Gas Fittings 7.5 External Gas Connection If the external gas connection is not in use, always close the stopcock (Fig. 57,2). Only gas appliances with a suitable adapter should be connected to the external gas connection. Connect only external gas appliances which are designed for an operation pressure of 30 mbar. Once you have made the connection and opened the stopcock, make sure that no gas is escaping at the connection point (Fig. 57,1).
Electrical Fittings 8 Chapter Overview 8 Electrical Fittings This chapter contains instructions regarding the electrical fittings of the caravan. The instructions address the following topics: l safety l 240 V power supply l connection to the 240 V supply l 12 V power supply l power pack l explanations of terms relating to the battery l living area battery l panel l sockets l towing vehicle connection l electrical wiring Operation of the electric appliances of the caravan is described in chapter 10. 8.
8 Electrical Fittings 8.2 240 V Power Supply The 240 V connection is protected by a twopole automatic circuit breaker (Fig. 58,1 or Fig. 59,1). The power pack is integrated in the circuit breaker. The 240 V power supply provides electricity for: - sockets with earth contact - refrigerator - 12 V living area power supply The electrical appliances connected to the 12 V power supply of the caravan are supplied with voltage by the power pack or living area battery.
Electrical Fittings 8 8.2.1 240 V Connection Completely unwind the cable on cable drums to prevent overheating. Power cable: - three-core (3 x 2,5 mm2) flexible rubber sheathed cable - maximum 25 m in length - 1 plug with earth contact - 1 socket with earth contact In order to be prepared for all connection possibilities, HYMER AG recommends the following combinations: - Adapter cable: CEE 17 socket with earth contact (Fig. 60,1) – plug with earth contact ( Fig. 60,2).
8 Electrical Fittings 8.3 12 V Power Supply When the caravan is not connected to the 240 V power supply, 12 V supply is performed either by the battery of the connected towing vehicle or by the living area battery (Power Pack SE). If the caravan is electrically connected to the towing vehicle, the living area battery is charged by the vehicle generator when the vehicle’s engine is running. The living area battery has a limited power supply only.
Electrical Fittings 8 8.3.2 Terms Off-load voltage The off-load voltage is the voltage of the battery in idle condition, i. e. no current is consumed and the battery is not being charged. Closed circuit current Some electrical appliances, such as the clock and the indicator lamps, require continuous electric current, for this reason they are referred to as inactive appliances. The closed circuit current flows even if the 12 V main switch has been switched off.
8 Electrical Fittings 8.3.3 Living Area Battery (Power Pack SE) > Take note of the battery manufacturers users and maintenance instructions. > Prior to commencing a journey ensure the living area battery is fully charged. For this reason charge the battery for at least 20 hours before commencing the journey. > During the trip, use every opportunity to charge the living area battery.
Electrical Fittings 8 8.5 Energy Reserve of the Living Area Battery The capacity of a battery is limited as to time. The higher the number of electrical appliances, the faster the energy of the living area battery is consumed. A battery which has been installed for years has no longer the complete capacity available. To protect the living area battery, no more than 80 % of the battery’s capacity should be drawn.
8 Electrical Fittings 8.6 Charging the Living Area Battery (Power Pack SE) The acid in the battery is poisonous and corrosive. Any contact with the skin or the eyes is to be avoided. In the case of charging with an external charger there is danger of explosion. Only charge the battery in a well ventilated area and away from naked flames or possible sources of sparks. Always remove the living area battery from the caravan when charging it using an external charger.
Electrical Fittings 8 n Turn on the external charger. n See the instructions for use of the connected charger for information concerning charge period required for the battery. n Disconnect the external charger in reverse order. 8.7 Living Area Battery in the Winter If the caravan has not been operated for some time or the 240 V power supply has not been connected for some time, the living area battery will quickly lose its capacity at low outside temperatures.
8 Electrical Fittings 8.8.2 Thetford Cassette Fuse The fuse (Fig. 61,1) is located on the left-hand locker wall of the Thetford cassette. Type of fuse: flat fuse 3 A/purple. To change the fuse, open the Thetford cassette flap on the outside and pull out the Thetford cassette completely. 8.8.3 Fig. 61 Thetford cassette fuse Fig. 62 240 V automatic circuit breaker Fuse 240 V A two-pole safety cut-out (Fig. 62,1 and Fig. 63,1) in the power pack secures the 240 V power supply.
Electrical Fittings 8 8.9 Sockets 8.9.1 Antenna Connection For connection of an antenna, an antenna cable is laid in the caravan. The cable ends are hidden under the covers in the front of the caravan: - In the roof storage compartment (Fig. 64,1) - In the storage compartment on the floor (Fig. 64,2) The position is marked by signs. 8.9.2 Fig. 64 Antenna connection, pre-assembled Fig.
8 Electrical Fittings 8.10 Thirteen-Pin Plug Connection Diagram > Note the colours of the connecting cables which are fitted to the thirteen-pin plug of the towing vehicle. This makes any new connection which may be necessary easier. To connect the thirteen-pin plug with a seven-pin socket, use a commercially available adaptor. Plug side of the socket "Jaeger" system Fig.
Electrical Fittings 8 Connection diagram Contact number DIN specification Function Cable colour Cross section of the wire 1 L Left direction indicator Yellow 1.5 mm2 2 54 G Fog tail light Blue 1.5 mm2 3* 31 Earth (contacts 1, 2, 4 - 8) White 2.5 mm2 4 R Right direction indicator Green 1.5 mm2 5 58 R Right tail light, marker light, licence plate light Brown 1.5 mm2 6 54 Brake lights Red 1.5 mm2 7 58 L Left tail light, marker lamp, licence plate light Black 1.
8 Electrical Fittings 8.11 Towing Vehicle Installation (Power Pack SE) > The towing vehicle must be retrofitted with the corresponding cable cross sections and a relay (Fig. 67,1) for power the supply (controlled using the ignition) (see Fig. 67). > If the cable cross sections stipulated below are not adhered to, then it is possible that a correct charging of the living area battery during the journey is not possible. Fig. 67 Towing vehicle installation diagram (Power Pack SE) 8.
Appliances 9 Chapter Overview 9 Appliances This chapter contains instructions regarding the appliances of the caravan. The instructions refer exclusively to the operation of the appliances. Further information about the appliances can be found in the instruction manuals for the appliances, included separately with the vehicle. The instructions address the following topics: l heater l boiler l gas cooker l refrigerator 9.
9 Appliances 9.2 Hot-Air Heater In winter, check that the waste gas vent on the vehicle roof is free of snow and ice before using the heater. Never let gas escape unburned due to danger of explosion. When refuelling the towing vehicle, on ferries and in the garage, the heater must be turned off. Danger of explosion! From heat setting 3 to 4 on switch on circulating fan. There is danger of overheating! Do not damage the exhaust gas pipe. The waste gas vent may neither be closed nor blocked.
Appliances 9 9.2.2 Heater (Variant 1) Turning on: n Open the regulator tap on the gas bottle and the gas isolator tap "Heater". n Turn control knob (Fig. 69) on the heater to the required position and press it firmly. The automatic ignition produces ignition sparks. A clicking noise can be heard. n Keep the control knob pressed until there is a flame. Press down for another 10 seconds to activate thermocouple. > In case of problems wait for two Fig.
9 Appliances 9.2.3 Heater (Variant 2) The control knob (Fig. 70,1) has the following positions: - Off: - Large flame: P - Lighting position: Turning on: n Open the regulator tap on the gas bottle and the gas isolator tap "Heater". n Turn control knob (Fig. 70,1) on the heater Fig. 70 Heater (variant 2) to the lighting position and press it firmly. The automatic ignition produces ignition sparks. A clicking noise can be heard. n Keep the control knob pressed until there is a flame.
Appliances 9 9.2.4 Circulation Fan The circulation fan together with the gas heater ensures a better distribution of hot air in the caravan. n Turn the knob (Fig. 71,2 or Fig. 72,1) to the required position of the circulating fan. Manual control (e. g. ventilation) P Circulation fan off (switch has no function during heater operation) A Automatic operation (heating) > Further information can be ob- tained from the separate instruction manual "TRUMA".
9 Appliances 9.3 Ultraheat Additional Electric Heater > The additional electric heater only functions when the vehicle is connected to a 240 V power supply. The Ultraheat additional electric heater is built-in to the hot-air heater. Therefore there are three heating options: - Only the gas heater - Gas heater and electric heater - Only the electric heater The vehicle heats up faster if the additional electric heater is used.
Appliances 9 9.4 Boiler Never let gas escape unburned due to danger of explosion. When refuelling the towing vehicle, on ferries and in the garage, the boiler must be turned off. Danger of explosion! 9.4.1 Truma Hot Water Source Depending on the model, the caravan is fitted with a hot water source. > Switch off the hot water source when the caravan is not in use. > Never use hot water source without water inside it.
9 Appliances Filling with fresh water: n Connect the external 240 V power supply to the caravan and switch on the 240 V automatic circuit breaker. n Set switch (Fig. 74) to off. Indicator lamp (Fig. 74,1) does not light up. n Turn the drain cocks on the cap (Fig. 75,1) in a clockwise direction. n Set all the water taps to "Hot" and open them. Water pump pumps water into the hot water source. n Leave water taps on until water flows out free of bubbles. Hot water source is filled with water. Fig.
Appliances 9 9.4.2 Truma Boiler Depending on the model, the caravan is fitted with a boiler. Never let gas escape unburned due to danger of explosion. Remove cap from waste gas vent before using the boiler. Models with waste gas vent on the right-hand side of the vehicle: If the awning is put up and the boiler switched on, exhaust from the boiler may build up in the awning. Danger of suffocation! Make sure the area is sufficiently ventilated.
9 Appliances Filling with fresh water: n Close the boiler drain cock (Fig. 76,1). n Open all water taps and set to "Warm" position. Water pump is pumping water into the boiler. n Leave all water taps on until water is free of bubbles. Boiler is filled with water. n Close the water taps. Gas operation: n Remove cap from waste gas vent. n Open the regulator tap on the gas bottle and the gas isolator tap "Boiler". Fig. 76 Drain cock boiler Fig. 77 Operating switch for Truma boiler (gas operation) Fig.
Appliances 9 Combined operation: To heat the water in the boiler more quickly, switch on gas and electrical operation at the same time. Emptying: n Switch off boiler. Turn knob (Fig. 77,1) anticlockwise until it can go no further. n Open boiler drain cock (Fig. 76,1). In order to do this, set the rocking lever on the boiler drain cock in a vertical position. n Check if water has drained completely from the boiler (approx. 10 litres).
9 Appliances Turning on: n n n n Open the gas cooker lid. Fold out and fix flame protection. Open the regulator tap on the gas bottle and the gas isolator tap "Cooker". Turn the control knob (Fig. 79,1) on the burner you wish to use to the ignition position (large flame). n Press the control knob and hold it down until gas flows to the burner. n Light burner with a match or other suitable means of lighting.
Appliances 9 9.6.2 Operating Modes The refrigerator has 2 operating modes: - Gas operation - Electric operation (240 V AC or 12 V DC) The operating mode is set on the refrigerator panel. Infinitely variable regulation of the cooling power is only possible with gas operation and when the refrigerator is operated with 240 V. It is not possible with 12 V operation. > Select only one energy source. Gas operation Never let gas escape unburned due to danger of explosion.
9 Appliances Electrical operation The refrigerator can be operated with the following voltages: - 240 V AC - 12 V DC > Close the gas isolator tap "Refrigerator" when the refrigerator is operated electrically. 240 V operation: n Set 12 V switch (Fig. 81,1) to "0". n Set 240 V switch (Fig. 81,2) to "I". n Set thermostat (Fig. 81,3) to required refrigerating temperature between "1" and "7". n To deactivate, turn the thermostat control knob to "0". Refrigerator is turned off.
Appliances 9 Opening: n Push the green retainer lock (Fig. 82,4) to the side to release the locking device. The bolt (Fig. 82,3) will trip. n Open the refrigerator door by the recessed grip or by the curved handle. Closing: n Fully close the refrigerator door. n Press bolt (Fig. 82,3) down, so that it engages in the (Fig. 82,2). outer latched position Locking the refrigerator door in the ventilation position: Fig.
9 Appliances 100 Touring - 03/11-1 - englisch (EN) - 0731070 - HYW-0102-01EN
Sanitary Fittings 10 Chapter Overview 10 Sanitary Fittings This chapter contains instructions regarding the sanitary fittings of the caravan. The instructions address the following topics: l sink l fresh water canister or fresh water tank l waste water tank l toilet l complete water system The positions of the drain cocks are indicated in a table found at the end of this chapter. 10.1 Water Supply, General > Fill the fresh water canister or the fresh water tank only with fresh water.
10 Sanitary Fittings 10.2 Sink > Always tilt the water tap downwards before closing the cover. n Open the sink cover and lock it in the required position. n Then swing the water tap upwards. 10.3 Fresh Water Tank The fresh water tank is built into the seating group. 10.3.1 Fresh Water Filler Neck The filler neck for filling the fresh water tank is on the right or left side of the caravan depending on the model. > The fresh water filler neck is labelled with the word "WASSER" (water) (Fig. 83,1).
Sanitary Fittings 10 10.4 Filling the Fresh Water System > Never operate water pump when the fresh water canister or the fresh water tank is empty. With fresh water canister: n n n n n n n n Loosen retaining straps at the fresh water canister. Unscrew the cap of the fresh water canister. Remove water pump and water hose from the fresh water canister. Top up with fresh water. Place water pump in the fresh water canister and close the cap tightly. Secure fresh water canister with retaining strap.
10 Sanitary Fittings Fresh water tank: n Position the caravan horizontally. n Connect the 240 V power supply and switch on the 240 V fuse box (Fig. 58 or Fig. 59). As far as the Power Pack SE with living area battery is concerned, a 240 V supply is not necessary. n Close drain cocks for the boiler or hot water source. n Open the cap on the fresh water tank. n Close the drainage opening in the fresh water tank with the stopper (Fig. 84,1) provided. Fig.
Sanitary Fittings 10 10.5 Waste Water Tank Before commencing the journey, empty the waste water tank. > If there is any risk of frost, empty the waste water tank. > Never pour boiling water directly into the sink outlet. Boiling water could cause deformation and leaks in the waste water pipe system. > Only empty the waste water tank at disposal stations, camping sites or at specially established disposal points. The waste water tank is fixed. Emptying: n Turn the cap (Fig.
10 Sanitary Fittings 10.6 Thetford Toilet > If there is any risk of frost and the caravan is not heated, empty the Thetford cassette. > Do not sit on the lid of the Thetford toilet. The lid is not designed to bear the weight of a person and could break. > Use a suitable chemical for this toilet. The ventilation will merely remove the odour but not germs and gases. Germs and gases will have a detrimental effect on the sealing rubbers.
Sanitary Fittings 10 10.6.2 Thetford Toilet (Variant 2) Flushing: n Press flush button (Fig. 88,1) and at the same time rotate in an anticlockwise direction. n After flushing, turn flush button in a clockwise direction, the sliding trap is closed. Emptying: To empty, the sliding trap in the Thetford toilet must be closed. n Turn the flush button (Fig. 88,1) in a clockwise direction. The sliding trap is closed. Fig. 88 Thetford toilet, flush button (variant 2) Fig. 89 Opening the Thetford flap Fig.
10 Sanitary Fittings 10.7 Emptying the Water System > If the caravan is not heated and there is any risk of frost, empty the whole water system to avoid damage to built-in appliances and the caravan. > Take note of the environmental tip in this chapter. With fresh water canister: n n n n n n Switch off the 240 V power supply on the 240 V automatic circuit breaker. n n n n Hold the water pump up until the fresh water pipes are completely empty. Loosen retaining straps at the fresh water canister.
Care 11 Chapter Overview 11 Care This chapter contains instructions regarding the care of the caravan. The maintenance instructions address the following topics: l exterior of the caravan l interior l winter operation At the end of the chapter there is a checklist of measures you must carry out if you are not going to use the caravan for an extended period of time. The checklist address the following topics: l temporary lay-up l winter lay-up l start-up after a lay-up 11.1 External Care 11.1.
11 Care 11.1.2 Windows of Acrylic Glass Acrylic glass windows are delicate and require very careful handling. > Never rub when dry as dust particles might damage the surface! > Only clean with plenty of warm water, dish washing liquid and soft cloth. > Never use glass cleaning agents with chemical, abrasive or alcohol-containing addi- tives. Premature brittleness of the panes and associated cracks may result from their use. > Avoid contact of cleansing agents used for the body (e. g.
Care 11 11.1.5 Waste Water Tank Clean the waste water tank after every use of the caravan. n Open the cleaning opening on the waste water tank and the drain cock. n Rinse thoroughly with fresh water. 11.1.6 Entrance Step If the entrance step is lubricated, coarse particles of dirt can settle on the lubricant during the journey and cause damage to the operating mechanism of the entrance step. Therefore, do not lubricate the moving parts of the entrance step. 11.
11 Care n Brush insect screens on windows with a soft brush or vacuum with the brush attachment of the vacuum cleaner. n Brush blinds on windows with a soft brush. Grease or stubborn dirt may be removed with a mild soap at 30 °C (curd soap). n Clean fresh water canister or fresh water tank with water and dish washing liquid and rinse subsequently with plenty of clear water. 11.3 Winter Care De-icing salt damages the underbody and the parts open to water spray.
Care 11 11.4 Lay-Up 11.4.1 Temporary Lay-Up After the vehicle has been standing for a longer period (approx. 10 months) have the braking and gas systems checked by an authorised specialist workshop. Take into consideration that the fresh water is undrinkable after only a short time.
11 Care 11.4.
Care 11 11.4.
11 Care 116 Touring - 03/11-1 - englisch (EN) - 0731070 - HYW-0102-01EN
Customer Service and Maintenance 12 Chapter Overview 12 Customer Service and Maintenance This chapter contains instructions regarding the maintenance of the caravan. The instructions address the following topics: l stabiliser l replacing light bulbs l adjusting the tension of the spring on the insect screen l spare parts At the end of the chapter you will find the ERIBA (HYMER) service numbers and important instructions on how to obtain replacement parts. 12.
12 Customer Service and Maintenance 12.2 AKS 1300 Stabiliser Clean the stabiliser and the coupling head regularly. Use either thinners or white spirit. When lubricating the stabiliser ensure that no lubricant is on the friction pads. Checking the stabilising device (on the side of the friction pads): Prerequisite: Connection to AKS 1300, ball diameter 50 mm n Turn the hand wheel (Fig. 91,1), until it can be heard and felt that the torque limiting mechanism grates. Turn in a in a clockwise direction.
Customer Service and Maintenance 12 12.3 Replacing Bulbs and Fluorescent Tubes, Internal Bulbs and light fittings can be extremely hot. Therefore, allow lights to cool down before changing bulbs. Store bulbs in a safe place inaccessible to children. Do not use any bulb that has been dropped or which shows scratches in its glass. It may burst. Lights can get very hot. Always maintain a safety distance of 30 cm. Fire hazard! > Halogen bulbs should not be touched with the fingers.
12 Customer Service and Maintenance 12.3.3 Living Area Lamp Opening: n Press side panels (Fig. 95,1) slightly towards the outside. n Press the glass together gently and remove from the housing. n Change the faulty halogen bulb. n Press side panels slightly towards the outside. n Allow the lamp glass to engage first in the front, then in the back. Fig. 95 Living area lamp Fig. 96 Halogen lamp Fig. 97 Toilet light 12.3.4 Halogen Lamp Opening: n Turn the panel (Fig.
Customer Service and Maintenance 12 12.3.6 Awning Light Opening: n Press the housing gently together (Fig. 98) and pull it out towards you. n Change the halogen bulb. n Hook at the upper edge of the housing must engage with the recess of the holder. n Pres down housing. 12.4 Fig. 98 Awning light Fig. 99 Re-tensioning the spring tension Adjusting the Springs of the Blind and the Insect Screen > The spring adjustment screw cannot be turned back.
12 Customer Service and Maintenance 12.5 Spare Parts Every alteration of the original condition of the caravan can jeopardize road safety. The accessories recommended by HYMER AG and the original spare parts have been specially developed for your caravan and supplied by us. Your ERIBA dealer carries these products. The ERIBA dealer is informed about admissible technical details and carries out the required work correctly.
Customer Service and Maintenance 12 12.7 Warning and Information Stickers There are warning and information stickers on and inside the vehicle. Warning and information stickers are for the sake of safety and must not be removed. > Replacement stickers can be obtained from a ERIBA dealer. 12.8 Service Telephone Numbers 12.8.1 ERIBA (HYMER) Service Numbers The ERIBA (HYMER) service numbers are: - +49 180 2 496373 - +49 89 76764242 12.8.
12 Customer Service and Maintenance 124 Touring - 03/11-1 - englisch (EN) - 0731070 - HYW-0102-01EN
Wheels and Tyres 13 Chapter Overview 13 Wheels and Tyres This chapter contains instructions regarding the tyres of the caravan. The instructions address the following topics: l tyre selection l handling of tyres l changing a wheel At the end of the chapter there is a table you can use to find the correct tyre pressure for your caravan. 13.1 General > Wrong tyre pressure causes excessive wear and can lead to damage or even to tyre burst. This is why the tyre pressure should be checked regularly.
13 Wheels and Tyres n Check regularly that the wheel nuts are firm- ly seated. Re-tighten the wheel bolts of a changed wheel cross-wise (Fig. 101) after 50 km (30 miles). For tightening torque see section Tightening Torque. n When using new or newly painted rims, retighten the wheel bolts once again after approx. 1,000 to 5,000 km (600 miles to 1,000 miles).
Wheels and Tyres 13 13.3 Tyre Specifications 215/70 R 15C 190/107 Q Speed index (Q = 160 km/h) Load index code for twin tyres Load index code for single tyres Rim diameter in inches Tyre design (R = radial) Height-to-width proportion in percent Tyre width in mm 13.4 Handling of Tyres n Drive over kerbs at an obtuse angle. Otherwise the flanks of the tyres may get pinched. Driving over a kerb at a sharp angle can damage the tyre and result in it getting ruptured.
13 Wheels and Tyres 13.5 Changing a Wheel 13.5.1 General Instructions The spare wheel is in the living area with Puck L 225 GT and it is under the rear with all other models. Use a commercial scissor-type jack to change the wheel. The caravan must be on level, firm ground, secure from slipping. Before jacking up the caravan, firmly apply the handbrake. Prevent the caravan from rolling away by blocking the opposite wheel with the wheel chocks.
Wheels and Tyres 13 13.5.2 Changing a Wheel with Alloy Wheel Rims The resting surfaces of the wheels on the break drums must be clean and free of burrs. Only use fastening parts provided for to loosen the wheels lightly and ensure that they rest correctly and move freely, subsequently tighten the wheel nuts cross-wise with a suitable wrench. Many axles do not have a centring aid, flange or bolts. It must be ensured that the wheel nuts are equally centered above the bolt circle (no jamming).
13 Wheels and Tyres 13.6 Tyre Pressure Wrong tyre pressure causes excessive wear and can lead to damage or even to tyre burst. The information on pressure levels is valid for cold tyres. Tyres Tyre pressures (bar) Tyre pressure (psi) 135 R13 2.4 35 155 R13 2.4 35 165 R13 2.4 35 185/70 R13 2.4 35 195/70 R14 2.4 35 Please always observe the speed limits in the individual countries (see chapter 17). The caravans are constantly brought up to the latest technical standards.
Fault Search 14 Chapter Overview 14 Fault Search This chapter contains instructions about possible faults in the caravan. The faults are listed with their possible causes and corresponding remedies. The instructions address the following topics: l chassis l braking system l electrical fittings l gas fittings l gas cooker l hot water source l boiler l refrigerator l water supply l body The specified faults can be remedied with relative ease and without a great deal of specialised knowledge.
14 Fault Search 14.3 Electrical Fittings > A dryfill battery may only be replaced by a dryfill battery. Fault Cause Remedy Road light system does no longer work correctly Bulb is defective Remove cover, replace bulb.
Fault Search 14 Fault Cause Remedy No voltage from the living area battery (Power Pack SE) Living area battery discharged Charge living area battery immediately > An extended pe- riod of total discharge may cause irreparable damage to the living area battery Before laying up the caravan for a longer period, fully charge the living area battery Discharging is caused by inactive appliances (see chapter 8) 14.
14 Fault Search 14.5 Cooker Fault Cause Remedy Ignition fuse does not operate (flame does not burn after the control knobs are released) Heat-up time is too short Keep control knob pressed for approx. 15 to 20 seconds after ignition Ignition fuse is defective Contact ERIBA customer service Thermocouple sensor is incorrectly set Correctly reset thermocouple sensor (do not bend). The sensor tip should protrude by 5 mm beyond the burner.
Fault Search 14 14.6.2 Truma Boiler Gas operation Fault Cause Remedy Red indicator lamp "Fault" illuminates Air in the gas pipe system Switch off and on again.
14 Fault Search 14.6.
Fault Search 14 14.
14 Fault Search 138 Touring - 03/11-1 - englisch (EN) - 0731070 - HYW-0102-01EN
Weight Details for Special Equipment 15 15.1 15 Weight Details for Special Equipment Weight Details for Special Equipment Weight details for ERIBA special equipment are listed in the table below. If these objects are either in or on the caravan and are not part of the standard equipment, they have to be taken into consideration when determining the payload. All weight details are approximate. Observe the max. permissible gross weight.
15 Weight Details for Special Equipment 140 Touring - 03/11-1 - englisch (EN) - 0731070 - HYW-0102-01EN
Technical Data 16 16.1 16 Technical Data Technical Data The information on dimensions and weight is valid for caravans with standard equipment. > Only the details provided in the actual vehicle documentation of the caravan shall be binding with regard to the technical data. > The measurements as well as the net weight of the caravan may change when mounting accessories or special equipment. Differences due to manufacturing tolerances (+/- 5 %) are possible and admissable.
16 Technical Data 142 Touring - 03/11-1 - englisch (EN) - 0731070 - HYW-0102-01EN
Helpful Notes 17 Chapter Overview 17 Helpful Notes This chapter contains helpful tips on how to travel with the caravan. The tips cover the following topics: l road assistance in European countries l traffic laws in European countries l gas supply in European countries l safe ways to spend the night during travel l camping in winter At the end of the chapter there is a check list containing the most important equipment for your trip with the caravan. 17.
17 Helpful Notes Country Iceland Italy Croatia Latvia Lithuania Luxembourg Macedonia Netherlands Norway Austria Poland Portugal Romania Russia Sweden Switzerland Serbia and Montenegro Slovakian Republic Slovenia Spain Czech Republic Turkey 144 : Emergency Services Police : 112 112 : 118 112 : 94 92 : 112 110 : 112 110 : 112 113 : 94 92 : 112 112 : 113 112 : 144/112*** 133 : 999 997 : 112 112 : 961 955 : 03 02 : 112 112 : 144 117/112*** : 94 99 : 155 158 : 112 113 :
Helpful Notes 17 Country : Emergency Services Police : 03 02 : 104 107 : 199/112*** 199/112*** Ukraine Hungary Cyprus * ** *** ( Breakdown Service ( 112 UA (3 22) 27 01 12 ( MAK 188/(06-1) 3 45 17 44*** ( AA 22 31 31 31 = Number only applies to major cities = Outside major cities = In the mobile communication network 17.3 Specifications without guarantee Date: 04/2003 Speed Limits When travelling abroad, note and do not exceed the varying speed limits.
17 Helpful Notes Country In built-up areas (km/h) 50 Outside built-up areas (km/h) 80 Motorway (km/h) Italy 50 70 80 Croatia 50 80 80 Latvia 50 80 80 Lithuania 60 70 11010 Luxembourg 50 75 90 50/60 80 80 Netherlands 50 80 80 Norway 50 604/80 604/80 Austria 50 1005 1005 Poland 60 80 80 Portugal 50 70/8011 100 Romania 50 90 100 Russia 50 9013 9013 Sweden 50 806 806 Switzerland 50 80 8010 Serbia and Montenegro Slovakian Republic 60 80 80 60 80
Helpful Notes 17 Country Outside built-up areas (km/h) 70 Motorway (km/h) Turkey In built-up areas (km/h) 50 Ukraine 50 9013 9013 Hungary 50 70 80 Cyprus 50 80 100 1 2 3 4 5 6 7 8 9 10 11 12 13 80 On expressways, on roads with more than one lane in each direction Specifications without guarantee and on roads resembling highways In wet conditions 80 km/h In wet conditions 100 km/h Trailers with no brakes and a current gross weight exceeding 300 kg With trailer of more than 750 kg (max.
17 Helpful Notes 17.4 Driving with Low Beam in European Countries The following is a list of the European countries in which driving with low beam is required even during the day.
Helpful Notes 17 Country Sleeping on roads and fields yes Sleeping on privately owned lands no yes Great Britain X X Ireland X X Italy X Comments no X Observe the local regulations. Parking and staying overnight on free areas is prohibited. Permission from the local authorities must be obtained in order to stay overnight on privately owned land. Croatia X X Luxembourg X X Netherlands X X Norway X X Officially prohibited on rest areas and cultivated grounds.
17 Helpful Notes 17.6 Gas Supply in European Countries > In Europe, there are several different connection systems for gas bottles. It is not al- ways possible to fill or exchange your gas bottles in a foreign country. Get information about the connection system in the country you are travelling to before embarking on your journey, e. g. at a motoring club or in the trade press. General tips: l Only go on vacation with completely filled gas bottles. l Use all of the gas bottles’ capacity.
Helpful Notes 17 l Only operate the gas system using propane. l Follow the instructions in the chapter "Gas Supply in European Countries". l Use a two-bottle system with automatic controller for the gas system, so that the supply does not run out during the night. l Do not use the space behind the heater as a storage compartment. l Never operate catalytic ovens or infra-red gas radiators in the interior of the vehicle, since they consume oxygen for burning.
17 Helpful Notes Living area 4 Object Dustbin List of addresses Registration confirmation(s) Road atlas Bath towels Bath shoes Batteries Bed sheets Bed linen Laundry bag Books Camping guide Spare bulbs Vehicle documents Water bottle Binoculars Fire extinguisher Driving licence 4 Object Gas bottle Green insurance card Insect lamp Insect repellent Deck of cards Broom Candles Dust pan Coat-hangers Clothes brush Pillow Credit card Map Medicine Music cassettes Neck-supporting pillow Sewing kit Identity card R
Helpful Notes 17 Outside 4 Object Stay rope Bellows Camping chairs Camping table Touring - 03/11-1 - englisch (EN) - 0731070 - HYW-0102-01EN 4 Object Luggage racks Tent pegs/tightening ropes Lock 4 Object String 153
17 Helpful Notes 154 Touring - 03/11-1 - englisch (EN) - 0731070 - HYW-0102-01EN
Circuit Diagrams 18 18.
12 V circuit diagram 18 Circuit Diagrams 156 Touring - 03/11-1 - englisch (EN) - 0731070 - HYW-0102-01EN
Power Pack SE principle Circuit Diagrams 18 Touring - 03/11-1 - englisch (EN) - 0731070 - HYW-0102-01EN 157
12 V circuit diagram Power Pack SE 18 Circuit Diagrams 158 Touring - 03/11-1 - englisch (EN) - 0731070 - HYW-0102-01EN
Index 19 12 V power supply . . . . . . . . . . . . . . . . . . . 74 240 V automatic circuit breaker . . . . . . . . . 72 240 V connection . . . . . . . . . . . . . . . . . . . . 73 Fault search . . . . . . . . . . . . . . . . . . . . 132 Power cable . . . . . . . . . . . . . . . . . . . . . 73 240 V power supply . . . . . . . . . . . . . . . . . . 72 240 V power supply see also 240 V connection . . . . . . . . . . . . . 72 19 Index A Accessories, fitting . . . . . . . . . . . . . . . . . . . 20 Adapter .
19 Index Washing, with a high-pressure cleaner . . . . . . . . . . . . . . . . . . . . . . . . 109 Waste water tank . . . . . . . . . . . . . . . . 111 Windows . . . . . . . . . . . . . . . . . . . . . . . 110 Carpet, cleaning . . . . . . . . . . . . . . . . . . . . 111 Check list Before the Journey . . . . . . . . . . . . . . . . 35 For a temporary lay-up . . . . . . . . . . . . 113 For the journey . . . . . . . . . . . . . . . . . . 151 Initial start-up after temporary lay-up . . . . . . . . . . . . . . .
Index 19 Fixed table Rotating the table-top . . . . . . . . . . . . . . 53 Shifting the table-top . . . . . . . . . . . . . . . 53 Flap lock Closing . . . . . . . . . . . . . . . . . . . 43, 44, 45 Opening . . . . . . . . . . . . . . . . . . 43, 44, 45 Folding table Putting up . . . . . . . . . . . . . . . . . . . . . . . 54 Removing . . . . . . . . . . . . . . . . . . . . . . . 54 Folding table in bedside locker . . . . . . . . . . 55 Forced ventilation . . . . . . . . . . . . . . . . . . . .
19 Index Fresh water, filling with . . . . . . . . . . . . . 92 Operation . . . . . . . . . . . . . . . . . . . . . . . 92 Hot-air heater . . . . . . . . . . . . . . . . . . . . . . . 86 I Impermeability . . . . . . . . . . . . . . . . . . . . . . . 4 Indicator lamp, toilet . . . . . . . . . . . . . . . . . 106 Information stickers . . . . . . . . . . . . . . . . . 123 Insect screen Cleaning . . . . . . . . . . . . . . . . . . . . . . . 112 Spring, adjustment . . . . . . . . . . . . . . .
Index 19 R Refrigerator . . . . . . . . . . . . . . . . . . . . . . . . . 96 12 V operation, switching on/off . . . . . . 98 240 V operation, switching on/off . . . . . 98 Door lock . . . . . . . . . . . . . . . . . . . . . . . 98 Electrical operation . . . . . . . . . . . . . . . . 98 Fault search . . . . . . . . . . . . . . . . . . . . 136 Gas operation . . . . . . . . . . . . . . . . . . . . 97 Gas operation, switching on/off . . . . . . 97 Operating modes . . . . . . . . . . . . . . . . .
19 Index Travel check lists . . . . . . . . . . . . . . . . . . . Travelling with low beam . . . . . . . . . . . . . Tread depth . . . . . . . . . . . . . . . . . . . . . . . Tyre change see wheel change . . . . . . . . . . . . . . . . . . Tyre pressures . . . . . . . . . . . . . . . . . . . . . Tyre specifications . . . . . . . . . . . . . . . . . . Tyres . . . . . . . . . . . . . . . . . . . . . . . . . . . . Bearing capacity . . . . . . . . . . . . . . . . . Certification . . . . . . . . . . . . . . . .
