BUSH HOG ® ATH/ FTH Air Tunnel & Flat Deck Finishing Mowers Operator’s Manual Model ATH 720 Air Tunnel Model FTH 600 Flat Tunnel ASSEMBLY l OPERATION l MAINTENANCE 04/09 Rev.1 $4.
CONGRATULATIONS! You have invested in the best implement of its type on the market today. The care you give your Bush Hog implement will greatly determine your satisfaction with its performance and its service life. We urge a careful study of this manual to provide you with a thorough understanding of your new implement before operating, as well as suggestions for operation and maintenance. If your manual should become lost or destroyed, Bush Hog will be glad to provide you with a new copy.
ATH / FTH FINISHING MOWER Operator’s Manual TABLE OF CONTENTS SECTION/PARA SECTION/PARA PAGE PAGE IV MAINTENANCE . . . . . . . . . . . . . . . . . . . .10 4-1 Maintenance Check List . . . . . . . . . .10 4-2 Lubrication . . . . . . . . . . . . . . . . . . . . .10 4-3 Belt Adjustment . . . . . . . . . . . . . . . . .11 4-4 Belt Replacement . . . . . . . . . . . . . . .11 4-5 Blade Replacement . . . . . . . . . . . . . .12 4-6 Troubleshooting . . . . . . . . . . . . . . . . .12 Warranty . . . . . . . . .
LIMITED WARRANTY OOOOOOOOOOOOOOOOOOOOOOOOOOOOOOO Bush Hog warrants to the original purchaser of any new Bush Hog equipment, purchased from an authorized Bush Hog dealer, that the equipment be free from defects in material and workmanship for a period of one (1) year for non-commercial, state and municipalities’ use and ninety (90) days for commercial use from date of retail sale. Models ATH & FTH gearboxes are covered by a five (5) year limited warranty period.
DEALER PREPARATION CHECK LIST ATH / FTH FINISHING MOWERS BEFORE DELIVERING MACHINE — The following check list should be completed. Use the Operator’s Manual as a guide. o o o o o r o o 1. Assembly completed. o 9. Warranty information has been filed online with Bush Hog. 2. Gearboxes filled with oil. 3. All fittings lubricated. 4. All shields in place and in good condition. 5. All fasteners torqued to specifications given in Torque Chart 6. All decals in place and readable. (See decal page.) 7.
IMPORTANT SAFETY PRECAUTIONS This symbol is used to call attention to safety precautions that should be followed by the operator to avoid accidents. When you see this symbol, carefully read the message that follows and heed its advice. Failure to comply with safety precautions could result in death or serious bodily injury.
IMPORTANT FEDERAL LAWS AND REGULATIONS* CONCERNING EMPLOYERS, EMPLOYEES AND OPERATIONS. *(This section is intended to explain in broad terms the concept and effect of the following federal laws and regulations. It is not intended as a legal interpretation of the laws and should not be considered as such). U.S. Public Law 91-596 (The Williams-Steiger Occupational and Health Act of 1970) OSHA This Act Seeks: “...
SECTION I INTRODUCTION AND DESCRIPTION Parallel uplift blades form a suction during operation to lift the grass before cutting it. The four caster wheel arrangement, along with the floating lift linkage and optional front mounted roller, all work together to give an even cut and minimize scalping. 1-1 INTRODUCTION We are pleased to have you as a Bush Hog customer. Your ATH/FTH Series Rotary Cutter has been carefully designed to give maximum service with minimum down time.
SECTION II PREPARATION FOR USE 2-1 ATTACHING TO TRACTOR NOTE Due to the many variations in tractor/implement hitch points and corresponding differences in distances between tractor PTO shafts and implement input shafts, drivelines may need to be shortened as described in the following steps: WARNING NEVER STAND BETWEEN TRACTOR AND CUTTER WHILE TRACTOR IS BEING BACKED TO HITCH. WARNING ADDITIONAL TRACTOR FRONT BALLAST MAY BE NEEDED FOR STABLE OPERATION AND TRANSPORT OF CUTTER.
G. Clamp end of driveline in a vice. Cut off shield where marked. (Figure 2-3). Figure 2-5 Figure 2-3 DANGER MAKE CERTAIN DRIVELINE YOKES ARE SECURELY FASTENED. FAILURE TO DO SO MAY RESULT IN SERIOUS INJURY. H. Using cut off section of shield as a guide, cut shaft the same amount. (Figure 2-4) Figure 2-4 L. Raise cutter off ground and adjust lower lift arms to level cutter right to left. Refer to tractor operator’s manual. M. Lower cutter to work position.
SECTION III OPERATING INSTRUCTIONS 3-1 GENERAL SAFETY Figure 3-1 Only qualified people familiar with this operator’s manual and tractor operator’s manual should operate this machine. Operator should wear hard hat, safety glasses and safety shoes. The operator should read, understand and practice all safety messages shown on the caution, warning and danger decals affixed to the cutter to avoid serious injury or death.
SECTION IV MAINTENANCE 4-1 MAINTENANCE CHECK LIST 8.During operation, listen for abnormal sounds which might indicate loose parts, damaged bearings, or other damage. Correct any deficiency before continuing operation. Perform scheduled maintenance as outlined below. Lower implement to ground, turn off tractor, and set parking brake before doing maintenance inspections or work. Some checks may require raising machine off ground and supporting with blocks.
4-4 BELT REPLACEMENT 40 HOURS 7. Spindle Assembly - Apply multi-purpose grease with grease gun until grease purges out relief hole. Grease fittings for spindles should be accessed by removing the plastic plugs in the shields. After completing lubrication, replace plastic plugs.. Use only genuine Bush Hog replacement parts. A. Remove right and left side shields. B. Relieve spring tension by loosening the two 3/8” hex nuts on the spring adjustment rod. (Figure 4-1C) C. Remove old belt. D.
Figure 4-2 Blade Placement 4-5 BLADE REPLACEMENT CAUTION WEAR HEAVY WORK GLOVES TO PROTECT HANDS FROM SHARP EDGES. A. Raise cutter using tractor 3-point lift and SECURELY BLOCK INTO POSITION. B. Turn off tractor, set parking brake and remove key. C. Remove bolt and cup washer securing blade to spindle. Remove blade. D. Install new blade as shown in Figure 4-2 with concave side of cup washer against blade. Be sure that blades are installed with offset in proper direction. Tighten retaining bolt to 76 ft.
SECTION V DEALER ASSEMBLY 10. If the assembly calls for welding or cutting, be sure that there are no flammable materials close at hand and that bystanders have taken necessary precautions. CAUTION THE FOLLOWING SAFETY PRECAUTIONS SHOULD BE THOROUGHLY UNDERSTOOD BEFORE ATTEMPTING MACHINE ASSEMBLY. AFTER COMPLETING ANY ASSEMBLY STEP, THOROUGHLY READ THE NEXT STEP IN THE ASSEMBLY INSTRUCTIONS BEFORE PROCEEDING WITH THAT STEP. 1.
D. Loosely attach two caster arms to the front of the mower deck using 5/8 x 3-1/2” bolts, lockwashers and hex nuts. Install reinforcement plates between bolt heads and caster arms. Loosely attach the remaining two caster arms to the rear of the mower deck using 5/8 x 3-1/2” bolts, lockwashers and hex nuts in each caster arm. Attach mast supports to the rear of the mower deck at rearholes of caster arms using 5/8” x 4” bolts, lockwashers and hex nuts.
SAFETY DECALS To promote safe operation, Bush Hog supplies safety decals on all products manufactured. Because damage can occur to safety decals either through shipment, use or reconditioning, Bush Hog will, upon request, provide safety decals for any of our products in the field at no charge. Contact your authorized Bush Hog dealer for more information. 50042283 50042285 50042282 50012616 78608 78786 83056 IMPLEMENT CAN FALL FROM HYDRAULIC SYSTEM RELEASE.
TORQUE SPECIFICATIONS Proper toque for American fasteners used on Bush Hog equipment. Recommended Torque in Foot Pounds (Newton Meters).* AMERICAN Bolt Head Markings SAE Grade 2 (No Dashes) SAE Grade 5 (3 Dashes) ” lt Bo ter “B e m Dia Wrench Size “A” SAE Grade 8 (6 Dashes) METRIC WRENCH SIZE (IN.) “A” BOLT DIAMETER (IN.
2501 Griffin Ave. l Selma, AL 36703 Telephone (334) 874-2700 l www.bushhog.