BUSH HOG ® BBC 48 / BBC 60 Box Blades Operator’s Manual OPERATION l MAINTENANCE 807 $4.
CONGRATULATIONS! You have invested in the best implement of its type on the market today. The care you give your Bush Hog implement will greatly determine your satisfaction with its performance and its service life. We urge a careful study of this manual to provide you with a thorough understanding of your new implement before operating, as well as suggestions for operation and maintenance. If your manual should become lost or destroyed, Bush Hog will be glad to provide you with a new copy.
® BUSH HOG BBC BOX BLADE OPERATOR’S MANUAL TABLE OF CONTENTS SECTION PAGE Warranty -------------------------------2 Dealer Preparation Check List ---3 Safety Precautions ------------------4 Laws and Regulations--------------5 Specifications-------------------------6 I OPERATION--------------------------6 SECTION PAGE Attachment ----------------------------6 Detaching From Tractor -----------6 Operation ------------------------------7 II MAINTENANCE ---------------------7 III Safety Decals ----------------
LIMITED WARRANTY OOOOOOOOOOOOOOOOOOOOOOOOOOOOOOO Bush Hog warrants to the original purchaser of any new Bush Hog equipment, purchased from an authorized Bush Hog dealer, that the equipment be free from defects in material and workmanship for a period of one (1) year for non-commercial, state, and municipalities’ use and ninety (90) days for commercial use from date of retail sale. The obligation of Bush Hog to the purchaser under this warranty is limited to the repair or replacement of defective parts.
DEALER PREPARATION CHECK LIST BOX BLADES BEFORE DELIVERING MACHINE — The following check list should be completed. Use the Operator’s Manual as a guide. r r r r r 1. Assembly completed. 2. All fasteners torqued to specifications given in Torque Chart. 3. All decals in place and readable. (See decal page.) 4. Overall condition good (i.e. paint, welds) 5. Operators manual has been delivered to owner and he has been instructed on the safe and proper use of the implement.
IMPORTANT SAFETY PRECAUTIONS This symbol is used to call attention to safety precautions that should be followed by the operator to avoid accidents. When you see this symbol, carefully read the message that follows and heed its advice. Failure to comply with safety precautions could result in serious bodily injury.
IMPORTANT FEDERAL LAWS AND REGULATIONS* CONCERNING EMPLOYERS, EMPLOYEES AND OPERATIONS. *(This section is intended to explain in broad terms the concept and effect of the following federal laws and regulations. It is not intended as a legal interpretation of the laws and should not be considered as such). U.S. Public Law 91-596 (The Williams-Steiger Occupational and Health Act of 1970) OSHA This Act Seeks: “...
SPECIFICATIONS MODEL BBC-48 Working Width Moldboard Height BBC-60 48” 60” 11-1/2” 11-1/2” 12” 12” Overall Depth Box Depth 18-3/4” 18-3/4” Overall Height 26-1/4” 26-1/4” Overall Width 48-3/4” 60-3/4” 1/4” 1/4” 3/4” x 2-1/2” 3/4” x 2-1/2” 4 5 Side Sheet Thick. Scarifier Size Scarifier Teeth Hitch Category 1 Category 1 Lower Hitch Cat 1 Pin Cat 1 Pin Cutting Edge 1/2” x 6” 1/2” x 6” Number of Blades 2 2 248 lbs. 258 lbs. 24 (Maximum) 24 (Maximum) Approx.
Figure 3 Scarifier Shank Adjustment Pin Replaceable Tips Reversible Blade OPERATION Level the box blade from side to side and front to rear using adjustments on the tractor’s 3-point lift. SECTION II - MAINTENANCE To adjust the scarifier shanks, first remove the pins which hold the shanks in place. Slide the shanks up or down to desired position and replace the pins. (Figure 3) Keep all blade nuts and bolts tightened to 175 ft. lbs. Blades can be reversed to use opposite cutting edge when needed.
SAFETY DECALS To promote safe operation, Bush Hog supplies safety decals on all products manufactured. Because damages can occur to safety decals either through shipment, use or reconditioning, Bush Hog will, upon request, provide safety decals for any of our products in the field at no charge. Contact your authorized Bush Hog dealer for more information.
TORQUE SPECIFICATIONS Proper toque for American fasteners used on Bush Hog equipment. Recommended Torque in Foot Pounds (Newton Meters).* AMERICAN Bolt Head Markings W RENCH S IZ E (IN .) “ A ” B O L T D IA M E T E R (IN .
P.O. Box 1039 l Selma, AL 36702-1039 Telephone (334) 874-2700 l www.bushhog.
