User guide

28
For any help concerning set up and use of your TV please call the Customer Helpline: 0871 2000 463
Option 1) Connecting your TV to your Sky box
(when both the TV and Sky Box are located in the same room)
Option 2) Connecting your TV to your Sky box (when your Sky box is located in a different room to the TV)
Depending on your Sky Box & TV model, connect either by SCART or HDMI
cables (available separately)
If connecting by SCART, select the ‘Input source’ on the TV as SCART.
If connecting by HDMI, select the ‘Input source’ on the TV as HDMI (if the TV has
more than 1 HDMI port, ensure you select the input source to match the HDMI
numbered port on the rear of the TV)
If you wish to use your Sky remote to operate the TV’s functions, you will need a
Sky remote control (Revision 9 or later) and you will need to programme a 4 digit
code into it. See bottom of this page.
Sky Box
SCART or HDMI
cable
RF/COAX cable from
Sky Box to 2nd TV
Connect to RF
or RF2 output
on the Sky box
Connect to the
Aerial/RF input
on the 2nd TV
TV Link/Magic Eye
(optional)
2nd TV in
another room
Sky Box
SCART
or HDMI
cable
Using a Sky Remote or a Universal Remote to operate your TV - Sky Remote Control, If you wish to use your
Sky remote to operate the basic functions of your TV, you need to programme a 4 digit code into it. Please note.
you will need the latest Sky Revision 9 remote control as this is the only version that includes the latest software/
fi rmware necessary to operate this model of TV. The code required for this television is 2134. If you wish to
upgrade/replace your existing Sky remote control to the latest version, you can do so on our web site.
Universal Remote Control, If you wish to use a Universal remote control to operate your TV, please refer to the web
site for a full list of codes. (Please note we only have codes for One for All branded remote controls, if you have an
alternative brand of Universal remote, please refer to the manufacturer for the code.)
Using Your TV With a Sky Digital Set
Top Box
Please note, if you are adding a ‘Magic Eye/TV Link’
to your system so that you can use your Sky remote
control to change the Sky channel in the room where
the 2nd TV is located, please refer to the instructions
included with the TV link/magic eye in order to
ensure the RF or RF2 output on your Sky box is
powered on. (The red LED light on the TV link/magic
eye will light up if the RF / RF2 output is correctly
set up) If you do not have the instructions that came
with the TV link/magic eye, instructions on how to do
it can be found on our web site.
1) To tune the TV to the Sky box, on the 2nd TV, select the ‘Analogue’ input source.
2) Select the channel that you wish to store the Sky box/channel on. (If you do not use channels 1-5 because you
no longer have analogue terrestrial channels after digital switchover, you may choose to select channel 1 to store
the Sky box/channel, if you still have and use analogue channels 1-5, you may for example decide that channel 6 is
the best option for you)
3) Press the corresponding number on the remote control to select the desired analogue channel chosen as per
point 2 above.
4) On the TV remote control, press Menu. Now navigate through the menus to select Manual Tuning or Analogue
Manual tuning (refer to the Tuning/Channel menu section of this user guide if necessary)
5) Manually tune in the channel (usually, the Sky box is at a frequency between 800Mhz and 850Mhz) once the
Sky box/channel is found, press ‘OK’ to store it.
If you wish to use your Sky remote to operate the TV’s functions, you will need a Sky remote control
(Revision 9 or later) and you will need to programme a 4 digit code into it. Please see below.
UserGuide - Bush -42-333ART Bush - 42-333ART3D 47-333ART3D.indd Sec1:28UserGuide - Bush -42-333ART Bush - 42-333ART3D 47-333ART3D.indd Sec1:28 9/2/2013 3:17:48 PM9/2/2013 3:17:48 PM