User Manual

WARNING: IF THE SIGHT IS NOT MOUNTED FAR ENOUGH FORWARD, ITS REARWARD MOTION MAY

INJURE THE SHOOTER WHEN THE RIFLE RECOILS.

MOUNTING DETAILS BY MODEL

Enrage/Incinerate

1. Set the mount onto the base rail or bases so that they align with the crosscut grooves.

2. Work the mount into the base until the crossbolt seats into the groove.

3. Securely tighten the locking nut with a coin or screwdriver. CAUTION: Do not overtighten.

TRS-26

1. Loosen the shaft by means of the provided multi-tool, so that the locking bar can clamp around the Picatinny/ Weaver

rail.

2. Install the sight to the weapon rail by tightening the shaft. First, ensure that the sight is correctly positioned and that

the shaft ts into a groove on the Picatinny/Weaver rail. To make sure that the shaft is rmly tightened, screw the shaft

clockwise until a light resistance can be encountered. CAUTION: Do not overtighten.

3. Finally, make sure that the shaft with locking bar is rmly tightened around the base rail.

First Strike 2.0

1. Any Weaver or Picatinny style base is suitable for mounting the First Strike 2.0. Make sure the base you use is

manufactured specically for your pistol, rie or shotgun. Be sure the base is properly installed and securely fastened

according to the manufacturer’s instructions for your safety.

2. Loosen the hex bolt on the mount of the sight using the provided tool. Position the mount on your base rail so that the

crossbolt engages a slot. Tighten the hex bolt. CAUTION: Do not overtighten.

ACTIVATING THE BATTERY

Before powering on your sight for the rst time, you will need to open the battery compartment and remove the protective

sticker or plastic disc from the battery. See the Parts Guide for the location of the battery compartment on your model.

REPLACING THE BATTERY

Should your reticle grow dim or not light at all, replace the battery. To install a new battery, unscrew the round battery

compartment cover (Enrage/Incinerate/TRS-26) using a coin, or pull out the battery tray* (First Strike 2.0). Insert a new CR2032

lithium battery, noting the position of the positive and negative sides, which varies by model (see Parts Guide). Replace

battery cover.

*(if necessary, insert a small screwdriver in the open slot of the First Strike’s battery tray to leverage the tray out slightly rst)

CAUTION: When replacing the battery cover, be sure that the O-ring is present and not damaged. Failure to do so could

result in water leakage into the battery compartment.

Verify that red dot is present by switching the power on and increasing the brightness if necessary (see next section).

SWITCHING POWER ON/OFF

To turn the sight’s power on and off:

(Enrage/Incinerate): Activate the illuminated dot by turning the rheostat knob to any numbered position. Toswitch

off the sight, select a dot mark between any two numbers.

(TRS-26/First Strike 2.0): Press and release the “Up” arrow button to power on the sight (“Down” button also works

on First Strike 2.0). To switch power off, press and hold the “Down” arrow button for 2.5 seconds. Note: power will

automatically switch off after 2 hours (TRS-26) or 8 hours (First Strike 2.0) to extend battery life if no button has been

pressed. Switch power on again to continue using the sight if necessary.

ADJUSTING DOT BRIGHTNESS

To adjust the brightness level of the dot reticle:

(Enrage/Incinerate): Turn the rheostat knob clockwise to increase brightness and counterclockwise to decrease

brightness. With the “1” lined up with the index mark, the dot will be the dimmest, and with a setting of “8”, the dot

is at the brightest illumination level.

(TRS-26/First Strike 2.0): Press and release the “Up” arrow button to increase brightness. Press and release the

“Down” arrow button to decrease brightness.