RIFLESCOPE INSTRUCTION MANUAL For Models with Capped Adjustments REN2736DW/ REN3940DW/ REN3950DW/ REN41240DW/ REN61850DW 05-17
Fast Focus Elevation Adjustment Eyepiece Side Focus Knob (Parallax Compensation) (selected models only) Power Change Ring Windage Adjustment PARTS GUIDE
Congratulations on your choice of a Bushnell® Engage® riflescope. It is a precision instrument constructed of the finest materials and assembled by highly skilled craftsmen for a lifetime of trouble-free use under the most demanding conditions. This booklet will help you achieve optimum performance by explaining how to use its various features and how to care for it. Read the instructions carefully before mounting and using your scope.
CENTERING THE RETICLE The reticle was carefully set at the optical center of your riflescope at our factory. This setting provides you with the ideal adjustment range from the center position. The riflescope’s adjustments are used to zero-in the riflescope. It is wise to check the center of the optical axis before mounting. Do this by placing the scope in a solid V-block (cardboard box with two slots). While looking through the scope in a normal viewing position, carefully rotate the scope.
. Tighten the mounting screws. WARNING: IF THE SCOPE IS NOT MOUNTED FAR ENOUGH FORWARD, ITS REARWARD MOTION MAY INJURE THE SHOOTER WHEN THE RIFLE RECOILS. BORE SIGHTING Bore sighting is a preliminary procedure to achieve proper alignment of the scope with the rifle’s bore. It is best done using a Bushnell® Bore Sighter. If a bore sighter is not available, it can be done as follows: Remove the bolt and sight through the gun barrel at a 100 yard target.
ELEVATION AND WINDAGE ADJUSTMENT Bushnell Engage scopes feature finger-adjustable audible-click elevation and windage adjustments. 1. Remove the covers from the Elevation and Windage Adjustments. 2. Grasp the Adjustment Bar and turn it in the appropriate “UP” (and/or “L”) direction indicated by the arrows. Each “click” or increment on the Adjustment Scale Ring will change bullet impact by 1/4” Minute of Angle.
1. Using a jeweler’s screwdriver, loosen the Phillips screw on the Adjustment Scale about 1/2 turn. Take care not to disturb your zero by “losing” a click or two when loosening the screws. 2. Rotate the Adjustment Scale Ring (which should now turn freely) to align the “O” with the Index Dot. 3. Retighten the screw in the Adjustment Scale and reinstall the Elevation and Windage Adjustment Knobs.
MAINTENANCE Your Bushnell riflescope, though amazingly tough, is a precision instrument that deserves reasonable cautious care. 1. When cleaning the lenses, first blow away any dirt and dust, or use a soft lens brush. Fingerprints and lubricants can be wiped off with lens tissue, or a soft clean cotton cloth, moistened with lens cleaning fluid. WARNING: UNNECESSARY RUBBING OR USE OF A COARSE CLOTH MAY CAUSE PERMANENT DAMAGE TO LENS COATINGS. 2. All moving parts of the scope are permanently lubricated.
in accurate windage holds. With accurate ballistic calculations, the Deploy MOA reticle delivers accurate shots, every time. SIGHTING IN / AIMING POINTS The Deploy reticle is intended to be sighted in at 100 yards, and is calibrated in MOA (minutes of arc). The reticle has wider markings every 5 MOA. The user can sight-in at 100 yds on any magnification setting, but for the Deploy reticle feature (range and windage marks) to function properly, the scope’s magnification must be set to the highest power.
THE BUSHNELL DEPLOY™ MOA RETICLE 1 MOA marks 5 MOA marks 10 Note: 1 MOA marks on vertical (elevation) axis are 2 MOA wide (for wind hold reference), and 5 MOA marks on vertical axis are 4 MOA wide. See next page.
THE BUSHNELL DEPLOY™ MOA RETICLE DIMENSIONAL SPECS 11
BUSHNELL IRONCLAD WARRANTY Products manufactured on or after April 2017 are covered by the Bushnell Ironclad Warranty. The Ironclad Warranty is a full lifetime warranty that covers the lifetime of this Product. Each Product has a defined lifetime; lifetimes can range from 1 to 30 years. This Product’s lifetime can be found at the website listed below and/or on the Bushnell webpage specific to this Product.
For further questions or additional information please contact: Bushnell Outdoor Products 9200 Cody, Overland Park, Kansas 66214 (800) 423-3537 • www.bushnell.com ©2017 Bushnell Holdings, Inc.