Owner manual

ManualsBrandsBuyers ManualsCar1501310

9049 Tyler Blvd. • Mentor, Ohio 44060

Phone (440) 974-8888 • Fax (440) 974-0165

Toll-Free Fax 800-841-8003 • buyersproducts.com

Installation Instructions

1501310 Van Ladder Rack

1501311 Van Ladder Rack Single Crossbar

Before assembling your Buyers’ ladder rack it is

important to read, understand, and follow all listed

instructions.

1. Crossbar Assemblies (Figs. 1 & 2)

• Using the M12 bolts and lock washer, install

each of the Side Mount Tubes to the Gutter Mount

Brackets. Use the top hole in the Gutter Mount

Bracket for the front and rear crossbars. Use the

bottom hole for a center crossbar (1501311).

NOTE: It is recommended that all weld nuts face rear-

ward to limit weather exposure and to prevent the set

screws from contacting objects carried on rack.

• If desired, slide one Divider Bracket onto each

Crossbar.

• Insert the Crossbars into the Side Mount Tubes.

2. Installing the Crossbar Assemblies

• Determine the location on your van to mount

each Crossbar Assembly.

• Place each Crossbar Assembly in the rain gutters

of the van. Be sure the outside edges of the Gutter

Mount Brackets sit against the widest part of the

gutter (against outer flanges).

3. Install the Clamp Brackets (Fig. 1)

NOTE: TWO styles of clamp bracket are included

in the kit in order to better cover multiple brands

of van. It is the responsibility of the installer and/

or end user to make sure the best fitting bracket is

used.

Line up each style of Clamp Brackets against the

Gutter Mount Bracket and below the gutter of your

van. After choosing the best fitting Clamp Bracket

style, install all four Clamp Brackets using the

included M7 hardware.

4. Final Assembly

• Position the Divider Brackets to desired locations

• Tighten all M10 set screws and confirm all other

hardware is tight.

WARNING

Never exceed any manufacturer rating or recommendation.

Maximum load for the Rack is 600 lbs (evenly distributed).

All loads should be evenly distributed

Be certain all loads are properly secured on Rack before

moving the van.

Always load the Rack as low as possible. Any load carried

on the Rack will affect stability of the Van and may increase

the tendency of the vehicle to rollover.

Before each use, verify all hardware remains tight and the

rack has remained in the proper position.

Summary of content (4 pages)

PAGE 1
9049 Tyler Blvd. • Mentor, Ohio 44060 Phone (440) 974-8888 • Fax (440) 974-0165 Toll-Free Fax 800-841-8003 • buyersproducts.com Installation Instructions 1501310 Van Ladder Rack 1501311 Van Ladder Rack Single Crossbar Before assembling your Buyers’ ladder rack it is important to read, understand, and follow all listed instructions. 1. Crossbar Assemblies (Figs. 1 & 2) • Using the M12 bolts and lock washer, install each of the Side Mount Tubes to the Gutter Mount Brackets.
PAGE 2
Fig. 1 DIVIDER BRACKET SIDE MOUNT TUBE GUTTER MOUNT BRACKET M12 CAPSCREW WITH LOCK WASHER M10 CAPSCREW M7 CAPSCREWS WITH FLAT WASHERS AND LOCKNUTS CLAMP BRACKET (3022873) ALTERNATE CLAMP BRACKET (3023087) Fig.
PAGE 3
1501310 Bill of Materials Bill of Materials Hardware Kit ITEM PART NO. QTY. 1 2 3 4 5 6 7 – 3023084 3023086 3022898 3022873 3023087 3022865 3022897 3022870 4 4 2 4 4 3 4 1 DESCRIPTION GUTTER MOUNT BRACKET SIDE MOUNT TUBE CROSSBAR CLAMP BRACKET CLAMP BRACKET, ALTERNATE DIVIDER BRACKET PLUG, TUBE HARDWARE KIT, VAN RACK 1501310 QTY.
PAGE 4
9049 Tyler Blvd. • Mentor, Ohio 44060 Phone (440) 974-8888 • Fax (440) 974-0165 Toll-Free Fax 800-841-8003 • buyersproducts.com 1501311 Bill of Materials 1 6 2 3 2 6 1 4 OR 5 Bill of Materials Hardware Kit ITEM PART NO. QTY. 1 2 3 4 5 6 – 3023084 3023086 3022898 3022873 3023087 3022897 3023090 2 2 1 2 2 2 1 DESCRIPTION GUTTER MOUNT BRACKET SIDE MOUNT TUBE CROSSBAR CLAMP BRACKET CLAMP BRACKET, ALTERNATE PLUG, TUBE HARDWARE KIT, 1501311 QTY.