Owner manual

ManualsBrandsBuyers ManualsCar1801005

Quality since 1946

I n s t a l l a t i o n I n s t r u c t i o n s

WARNING:

• Do not lubricate threads; hardware fail-

ure may occur due to overtightening.

• Do not drill or weld to this product.

• Use only Buyers supplied or approved

hardware to install this product.

CAUTION:

• To keep debris out of your eyes always

wear protective eyewear.

• Tighten screws and nuts only when it

is recommended by these instructions.

• Check contents of box against part list

to make sure all components are included.

Hitch Receiver,

Class 4 1801005

Chevy/GMC

1988-2000 Classic

•1999-2006 Silverado / Sierra 1500, 2500

•1996-2006 Silverado / Sierra 2500HD

DoDGe

1971-1993 Full size pickup

•1994-2001 Ram 1500

(drilling required on short bed)

•1994-2002 Ram 2500 (drilling required on short bed)

•1994-2002 Ram 3500 (drilling required on short bed)

ForD

1973-1996 Full Size Pickups

•1997-2004 F-150 Old Body Style

1997-2006 F-250 / F-350 Super Duty

ToyoTA

2000-2006 Tundra

• Indicates no drilling required

9049 Tyler Blvd. • Mentor, Ohio 44060

Phone (440) 974-8888 • Fax (440) 974-0165

Toll-Free Fax 800-841-8003 • buyersproducts.com

Summary of content (12 pages)

PAGE 1
9049 Tyler Blvd. • Mentor, Ohio 44060 Phone (440) 974-8888 • Fax (440) 974-0165 Toll-Free Fax 800-841-8003 • buyersproducts.
PAGE 2
Quality since 1946 Chevy & GMC (Classic), 1988-2000 Bill of Materials ITEM 1 2 3 4 5 6 7 PART NO. QTY. 3004980 3004908 3004909 FCS038016125 FWF038081006 FNE038016044 3004906 Tools Required •1/2" drill bit •9/16" socket •19 mm socket •15 mm socket 1 1 1 8 16 8 4 DESCRIPTION ITEM PART NO. Middle Section Side Bracket Side Bracket Screw, HHC-3/8-16 x 1.
PAGE 3
Quality since 1946 Chevy Silverado & GMC Sierra 1500, 2500, 1999-2006 Bill of Materials ITEM PART NO. 1 2 3 4 5 6 7 8 9 10 3004980 3004908 3004909 FCS038016125 FWF038081006 FNE038016044 3001384 FWF050106010 FNE050013053 3004907 QTY. 1 1 1 8 16 8 2 2 2 2 1. Remove 14 mm bolts from bottom of frame with a 21 mm socket. DESCRIPTION Middle Section Side Bracket Side Bracket Screw, HHC-3/8-16 x 1.
PAGE 4
Quality since 1946 Chevy Silverado & GMC Sierra 2500HD, 1999-2006 Tools Required •3/4" socket •3/4" wrench •9/16" socket •9/16" wrench •21 mm socket •Torque wrench Bill of Materials 1. Remove 14 mm bolts from bottom of frame with a 21 mm socket. 2. Bolt brackets on with 14 mm bolts that were just removed into holes as shown. Insert 1/2" screw with 1/4" plate through large hole in frame and into brackets as shown. Install 1/2" washers and lock nuts on bolts. Leave nuts loose at this time. ITEM PART NO.
PAGE 5
Quality since 1946 Dodge Full Size Pickups, 1971-1993 Tools Required •1/2" drill bit •3/4" socket •3/4" wrench •9/16" socket •9/16" wrench •Torque wrench Bill of Materials 1. Insert 1/2" screws with 1/4" plate down through 1" holes at end of frame. Fasten brackets to frame as shown with 1/2" washers and lock nuts. Leave nuts loose at this time. ITEM PART NO. 1 2 3 4 5 6 7 8 9 10 11 3004980 3004908 3004909 FCS038016125 FWF038081006 FNE038016044 3004907 3001384 FWF050106010 FNE050013053 3005078 QTY.
PAGE 6
Quality since 1946 Dodge Pickup (short bed), 1994-2001 2500, 3500 Models Only 2002 Tools Required •1/2" drill bit •3/4" socket •9/16" socket •13 mm socket •3/8" drill bit •3/4" wrench •9/16" wrench •Torque wrench Bill of Materials 1. Spare tire may need to be loosened for installation. 2. Bolt brackets to frame with 1/2" screws and 1/4" plates inserted through 1" holes in end of frame. Install two 3/8" thick spacers between frame and brackets at rear bolting locations.
PAGE 7
Quality since 1946 Dodge Pickup (long bed), 1994-2001 2500, 3500 Models Only 2002 Tools Required •3/8" drill bit •3/4" wrench •9/16" wrench •Torque wrench Bill of Materials •3/4" socket •9/16" socket •13 mm socket 1. Spare tire may need to be loosened for installation. 2. Bolt brackets to frame with 1/2" screws and 1/4" plates inserted through 1” holes in the end of the frame. Install two 3/8" thick spacers between frame and brackets at rear bolting locations. Install 1/2" washers and lock nuts.
PAGE 8
Quality since 1946 Ford Full Size Pickup, 1973-1996 & 1997 F-250/F-350 Super-Duty Bill of Materials Tools Required •1/2" drill bit •3/4" socket •3/4" wrench •9/16" socket •9/16" wrench •Two clamps •Torque wrench 1. Assemble middle section with side brackets as shown in picture. Leave screws finger-tight. Note: Be sure to use four holes to bolt side brackets to middle section. ITEM PART NO. QTY.
PAGE 9
Quality since 1946 Ford F-250/350 Super-Duty, 1997-2006 Bill of Materials Tools Required •1/2" drill bit •3/4" socket •3/4" wrench •9/16" socket •9/16" wrench •Torque wrench 1. Align side brackets with rear edge of frame. Attach brackets to frame as shown with 1/2" screws and 1/4" plates down through rear holes in frame. Install flat washers and lock nuts on these screws. Leave nuts loose at this time. ITEM PART NO. QTY.
PAGE 10
Quality since 1946 Ford F-150 & Light-Duty F-250, 1997-2003 Ford F-150 Old Style Only 2004 Bill of Materials Tools Required •3/4" socket •3/4" wrench •9/16" socket •9/16" wrench •Torque wrench 1. Align side brackets with rear edge of frame. Place 3/8" thick spacers between brackets and frame as shown. Attach brackets to frame as shown with 1/2" screws and 1/4" plates down through frame, spacers and brackets. Use first and last holes in the brackets. Install flat washers and lock nuts on screws.
PAGE 11
Quality since 1946 Toyota Tundra, 2000-2006 Tools Required •1/2" drill bit •3/4" socket •3/4" wrench •15/16" socket •15/16" wrench •21 mm socket •Torque wrench Bill of Materials 1. Use existing holes at rear of frame and install 1/2" screws through 1/4" plates and into frame. With 1/2" screws, washers and lock nuts attach brackets to frame. Do not install fasteners in the forward holes in brackets at this time. 2. Install middle section as shown. Use bolting locations indicated.
PAGE 12
9049 Tyler Blvd. • Mentor, Ohio 44060 Phone (440) 974-8888 • Fax (440) 974-0165 Toll-Free Fax 800-841-8003 • buyersproducts.com Quality since 1946 Warranty Buyers Products Co. warrants all truck/trailer hardware manufactured or distributed by it, to be free from defects in material and workmanship for a period of one year from date of shipment. Parts must be properly installed and used under normal conditions.