BYD F6 OWNER'S MANUAL 1
Foreword Thank you for choosing BYD F6. To help you use and maintain BYD F6, please read this manual carefully. BYD F6 adopts EFI engine, its wiring structure is very complex. Please do not install such additional device by yourself as: anti-theft system, central control lock, power window, speakers and so on, otherwise the failure caused by it will be not covered by the ―Warranty" of BYD.
CONTENTS F6 SPECIFICATION AND BRIEF INTRODUCTION. - 1 F6 Specification ............................................. - 1 Brief introduction ........................................... - 2 Control panel .................................................. - 3 Driver and Passenger Safety ............................... 4 Safety equipment................................................. 5 Three-point safety belt ........................................ 6 Safety belt tensioner (optional) .........................
Cup Holder ........................................................ 53 Bill Box ............................................................. 54 Sun Visor ........................................................... 54 Vanity Mirror(opotinal) ..................................... 55 Cigarette Lighter ............................................... 55 Front Ashtray..................................................... 55 Door light ..........................................................
Dust filter ........................................................ 119 Driving belt ..................................................... 120 Timing belt ...................................................... 122 Tire .................................................................. 122 Tire chains ....................................................... 125 Light ................................................................ 126 Vehicle storage ................................................
F6 SPECIFICATION AND BRIEF INTRODUCTION F6 Specification Model Length(mm) Dimensions Width (mm) Height (mm) Wheel base (mm) Front (mm) Wheeltrack Rear (mm) Curb weight (㎏) Gross weight (㎏) Tire type Approach angle (°) Departure angle (°) Front overhang (mm) Rear overhang (mm) Passenger Max. speed (km/h) Engine Model Engine type Displacement (ml) Rated Power (kW) 2.
Brief introduction 2
Control panel *If you want to use the horn, just press the pad around the “BYD” logo.
Driver and Passenger Safety Important Safety Precautions You‘ll find many safety recommendations throughout this section and this manual. The following recommendations are the ones we consider to be the most important. Always Wear Your Seat Belt A seat belt is the best protection in all types of collisions. Airbags are designed to supplement seat belts, but they are designed to inflate when the vehicle engages in a severe frontal impact.
Safety equipment Your vehicle is equipped with many safety devices that work together to protect you and your passengers during a crash. Some features do not require any action on your parts. These include a strong steel framework that forms a safety cage around the passenger compartment; front and rear crush zones will absorb the impact energy by crumpling in a crash, a collapsible steering column, and tensioners that tighten the front seat belts in a crash.
F6 OWNER’S MANUAL BYD AUTO Three-point safety belt Your seat belt system also includes an indicator on the instrument panel and a buzzer to remind you and your passengers to fasten your seat belts. Safety belt tensioner (optional) The seat belt restrains you by a belt across your shoulders, chest and hip. To fasten your belt, pull it out of the retractor and insert the tab into the buckle. Pull the belt to make sure the tab and the buckle are locked.
F6 OWNER’S MANUAL BYD AUTO Airbag Side airbag (optional) Friendly tips 1.Airbags do not replace seat belts. They are designed to supplement the seat belts. 2.Airbags offer no protection in rear impacts, rolling or minor frontal or side collisions. 3.Airbags can pose severe hazards. To do their job, airbags must inflate with tremendous force. So while airbags help save lives, they can cause minor injuries or more serious or even fatal injuries if occupants are not properly restrained or sitting properly.
F6 OWNER’S MANUAL BYD AUTO Seat and seat back This vehicle seat design allows you to maintain a comfortable, straighten sitting, and is able to make full use of the protection provided by the seat belts and energy absorption material of the seats. Adjusting your seat and seat back could also affect your safety. For example, being too close to the steering wheel or dashboard will increase the possibility that you or passengers are injured by the in floatable airbag or other items inside.
F6 OWNER’S MANUAL BYD AUTO Advice to pregnant women Friendly Tips Each time you have a prenatal checkup, ask doctor if it‘s okay for you to drive. 2.Never use a seat belt for both yourself and a child. During a crash, the belt could press deep into the child and cause serious or fatal injuries. Friendly Tips 1.Never use the same seat belt for two people. If do that, they could be very seriously injured in a crash. Advice to Parents 2.Do not add any other accessory to the seat belt. 1.
F6 OWNER’S MANUAL BYD AUTO can prevent children from accidentally falling out. Extreme danger! Under the section 94 of E.C.E regulations: 8.Please use the main switch power windows, preventing children from playing with power windows, or else they might be in danger when their body are out of the car window. playing 9.Do not leave children alone in a vehicle. A child left alone with the key in the ignition switch can accidentally start up the vehicle, possibly injuring themselves or others.
F6 OWNER’S MANUAL BYD AUTO Supplementary data for airbag Your SRS (supplemental restraint system) includes: 1.Two front airbags. The driver‘s airbag is installed in the center of the steering wheel; the front passenger‘s airbag is installed in the dashboard. Both are marked ‗‗SRS AIRBAG‘‘. 2 . Two side airbags for driver and a passenger, one for each side of the vehicle. The airbags are installed on the outer edge of the seat backs, marked with ‗‗SRS SIDE AIRBAG‘‘. (Refer to 13rd page) position.
F6 OWNER’S MANUAL BYD AUTO see what looks like smoke. This is actually powder from the airbag‘s surface. Although the powder is not harmful, people with respiratory problems may experience some temporary discomfort. If this occurs, get out of the vehicle as soon as it is safe.
F6 OWNER’S MANUAL BYD AUTO In the circumstances illustrated above, the airbags may not deploy.
F6 OWNER’S MANUAL BYD AUTO Possible Causes of Airbag Deployment wearing information, etc.), timely get maintenance from service stations, otherwise it will lead to system failures or abnormal work. The SRS airbags may deploy if the vehicles receive severe impact on the bottom as shown in the above illustrations. Friendly tips 1. Airbag is designed to match the certain vehicle models, any changes in the tire size, bumpers, chassis and other original equipments may affect the function of the airbags.
F6 OWNER’S MANUAL BYD AUTO even killed. 7. Don‘t stay or put any animals or objects near the driver, the front seat passenger and the air bags. It is extremely dangerous for an adult passenger to hold a child on the laps. 8. Don‘t install phone holder, cup, ash tray or any other attachments to the air bag cover or its function area. Otherwise, accidents triggering air bags will increase the possibility of human injuries. 9.
F6 OWNER’S MANUAL BYD AUTO The air bag system shutdown must be conducted by the BYD dealers or franchised service stores. After the shutdown, BYD dealers or franchised maintenance stores must label at the specific places and keep records. Friendly tips If the air bag system needs shutdown in some special occasions, please go to the BYD dealers or franchised service stores. Otherwise, serious injuries or death may be incurred.
F6 OWNER’S MANUAL BYD AUTO In any of the above circumstances, the airbags and seat belt tensioners may not work properly when they are needed. You shall ask for help from the BYD AUTO dealer as soon as possible. Friendly tips Ignoring the SRS indicator can result in serious injury or death if the airbag systems or tensioners do not work properly. Have your vehicle checked by a BYD AUTO dealer as soon as possible if the SRS indicator alerts you to a possible problem.
F6 OWNER’S MANUAL BYD AUTO Friendly tips Carbon monoxide gas is toxic. Breathing it can cause unconsciousness and even death. Avoid any enclosed conditions or activities that expose you to carbon monoxide. High levels of carbon monoxide can concentrate rapidly in enclosed areas, such as a garage. Do not run the engine with the garage door closed. Even with the door open, run the engine only long enough to move the vehicle out of the garage.
F6 OWNER’S MANUAL BYD AUTO 19
F6 OWNER’S MANUAL BYD AUTO Danger Warning ................................................................ Mirror 33 ............................................. Rear windshield defroster ................................................. Parking 34 brake ................................. Steering wheel adjustment ................................................ Front 34Seat Armrest ......................... This chapter gives information about the controls and displays used in the daily Adjustment: .....
F6 OWNER’S MANUAL BYD AUTO Position of control switches 21
F6 OWNER’S MANUAL BYD AUTO Indicators 22
F6 OWNER’S MANUAL BYD AUTO The instrument panel has many indicators to give you important information about your vehicle. Low Oil Pressure Indicator Seat Belt Reminder Indicator When turning the ignition switch to the ON (II) position, it reminds you and your passengers to fasten your seat belts. A buzzer also sounds if you have not fastened your seat belt. If you turn the ignition switch to the ON (II) position before fastening your seat belt, the buzzer sounds and the indicator flashes.
F6 OWNER’S MANUAL BYD AUTO Supplemental Restraint System (SRS) Indicator This indicator comes on briefly when you turn the ignition switch to the ON (II) position. If it comes on at any other time, it indicates a potential problem with your front airbags or automatic seat belt tensioners. This indicator will also alert you to a potential problem with your side airbags. For more information, refer to 17th page.
F6 OWNER’S MANUAL BYD AUTO Low Fuel Indicator Security System Indicator Front Fog lamp Indicator This indicator comes on with the front Fog lamp. Refer to 23nd page on operating the front Fog lamp. This indicator is located on fuel gauge. This indicator comes on as a reminder that you must refuel soon for the fuel is less than 8 liters in the tank. This indicator comes on when security system is set. Refer to 81st page for more information on the security system.
F6 OWNER’S MANUAL BYD AUTO Combination instrument Speedometer The speedometer shows the vehicle speed in kilometer per hour (km/h). Tachometer The tachometer shows the engine speed in rpm.To prevent damage to the engine; do not drive when tachometer finger is on the red area. Odometer The odometer shows the total distance your vehicle has run.
F6 OWNER’S MANUAL BYD AUTO Hodometer Coolant temperature gauge Fuel level gauge This meter shows the number of kilometers driven since you last reset it. This shows the temperature of the engine‘s coolant. During normal operation, the reading should be in the middle of the gauge. In severe driving conditions, such as very hot weather or a long period of uphill driving, the reading may reach near the red mark. If it reaches the red (Hot) mark, park safely to the side of the road.
F6 OWNER’S MANUAL BYD AUTO Information Display Screen (optional) 1. Driver side Temperature Information 1. 2. DVD/FM Information Driver side temperature information It is used for displaying the set temperature (℃) in the position of driver. 2. DVD/FM information Display related information about DVD and radio 3. Clock information 4. Passenger side/outside termperature information Display the passenger side/outside temperature (℃) 3.
F6 OWNER’S MANUAL BYD AUTO Headlight Rotary switch on operating lever control the lights. Turn the switch to position to turn on the parking lights, rear license plate lights and the indicator. Turn this switch to position to turn on the headlight. Turn the switch to AUTO position, headlight will turn on or off automatically according to the ambient illumination intensity from the sunlight illumination sensor. When the light switch is in either of these positions, the indicator is on as a reminder.
F6 OWNER’S MANUAL BYD AUTO Sunlight illumination sensor Sunlight illumination sensor is located on the top of instrument panel and beside left front treble loudspeaker. Do not cover the sensor or spatter any liquid. If you remove the key from the ignition switch with lights turned on, you will hear a reminder chime for turning off the lights when you open the driver‘s door. To switch dipped lights to high beams, push the lever forward until you hear a click.
F6 OWNER’S MANUAL BYD AUTO Front/rear fog lamp indicator is on for reminding. To turn on or off the rear fog lamp with the front lamp lighting, turn upward the switch one frame from Turning signal position and release it. Then the indicator on the instrument panel is on or off for a warning. If only turn the rear fog lamp on, turn the switch downward from OFF (· ) to position and release it.
F6 OWNER’S MANUAL BYD AUTO Combination illumination instrument The instrument panel will illuminate with dim brightness when you open the driver‘s door. The brightness will increase slightly when you insert the key in the ignition switch, then go to normal brightness when you turn the ignition switch to the ON (II) position. Windshield wiper If you do not insert the key in the ignition switch after opening the driver‘s door, the illumination will be off scores of seconds after you close the door.
F6 OWNER’S MANUAL BYD AUTO Danger Warning INT— the intermission adjustment knob adjust its intermission time to 7S, 5S, 3S and 1S with the raindrop number increase. LO & HI—wiper scrape continually. MIST—Push the control lever upwards from OFF position. The wiper will scrape high-speed until you release the control lever. So that can clean the windshield quickly. Pull the control lever of windshield wiper back to clean the windshield; the syringe will spray water and the wiper work at the some time.
F6 OWNER’S MANUAL BYD AUTO Rear windshield defroster Steering wheel adjustment Adjustment: The rear window defroster will clear fog, frost, and thin ice from the window. Push the defroster button to turn it on and off. The indicator in the button comes on to show the defroster is on. It shuts off when you turn off the ignition. The defroster will be turned on again when you restart the vehicle. To save battery power, when the rear windshield has good visibility you shall turn off defroster.
F6 OWNER’S MANUAL BYD AUTO Key Your vehicle comes with a set of keys as shown in the picture. The master key fits all the locks on your vehicle. 1.Ignition switch 2.Driver‘s door 3.Glove box You should have received a key number tag with your keys. You will need this key number if you ever have got a lost key replaced. Use only BYD-approved key blanks. Ignition switch Remote control Please refer to 39th page on how to use the remote control.
F6 OWNER’S MANUAL BYD AUTO LOCK (0)—You can insert or remove the key only in this position. To turn the key from ACCESSORY (Ⅰ) to LOCK (0), you must push the key in slightly. For a A/T vehicle, to remove the key, we suggest you put the shift lever in Park or neutral position. The parking lock will lock the steering wheel after you remove the key. If the front wheels are turned, the anti-theft lock may make it difficult to turn the key from LOCK (0) to ACCESSORY (Ⅰ).
F6 OWNER’S MANUAL BYD AUTO switch, push down the tab or push the top of main switch, then close the door. Remote control All doors can be locked from the outside by using the key in the driver‘s door. Each door has a lock tab on it. Push down the tab to lock the door and pull it up to unlock. When you push down the tab on the driver‘s door, all doors will be locked. While pulling the tab on the driver‘s door can only open the driver‘s door.
F6 OWNER’S MANUAL BYD AUTO The front ceiling light (optional) and the rear ceiling light (if the ceiling light switch is in the position under door open status) will come on when you press the UNLOCK button. If you do not open any door, the light stays on for about 30 seconds, and then fades out. If you relock the doors with the remote transmitter before 30 seconds have elapsed, the light will go off immediately. Press the trunk release button for several seconds to open the trunk.
F6 OWNER’S MANUAL BYD AUTO Regulations on Transmitter Short Distance 1.It is prohibited to change the emission frequency and increase the output power (do not allow install exterior amplifier). Besides, user is not allowed to replace the transmitting antenna without approval. 2.This device can not produce interference with operating radio-communication. Once this kind interference is founded, the action of the device will be stopped until effective remedy measures are adopted 3.
F6 OWNER’S MANUAL BYD AUTO Trunk Glove box Seat Adjustment Front Seat Manual Adjustment You should complete all adjustment of the seats before you start driving. When the seat is adjusted to the desired position, try to move the seat backward to make sure it is locked in place. You can open the trunk in either of the follow ways: 1.Pull up the release lever of trunk on the left side of driver‘s seat. 2.Press and hold the trunk release button on the remote transmitter.
F6 OWNER’S MANUAL BYD AUTO Manual Adjustment of Driver Seat Height Power Adjustment of Driver Seat (optional) There are two electromotor adjustment switches. The level switch can adjust the bottom of the seat in several directions. The short vertical switch can adjust the seat-back angle. You can adjust the position of the seats no matter the ignition switch is in which position. You should complete the adjustment of the seats before you start driving.
F6 OWNER’S MANUAL BYD AUTO Pushing the level switch forward or backward can move the seat forward and backward. Pulling up or pressing the front of the switch can move the front part of the seat up or down. 42 Pulling up or pressing the rear part of the switch can lift up or lower down the rear part of the seat.
F6 OWNER’S MANUAL BYD AUTO Driver Waist (optional) Pulling up or pressing the middle of the switch can lift up or lower down the middle of the seat. Pushing the rear switch along the direction of the seat-back can adjust the seat-back angle. 43 Support To change the waist support, move the lever on the right side of the seat-back forward or backward. Keep moving the lever forward or backward until you find a suitable position.
F6 OWNER’S MANUAL BYD AUTO Head rest The front seats of your vehicle are equipped with adjustable headrest. Headrest can protect you and your passengers from injuries to neck and other parts of head. They are most effective when you adjust them so the back of the occupant‘s head rests against the center of the rest. Tall people should adjust the head rest higher. The height of front headrest is adjustable. You need both hands to adjust it. Do not attempt to adjust it while driving.
F6 OWNER’S MANUAL BYD AUTO Don‘t drive the car when the passage cap of trunk as well as the trunk lid is opened. Please refer to 21st page about the danger of carbon monoxide. Seat Heating Device (optional) When heating, the HI or LO indicator will remains on until you press the opposite side of the switch to stop heating. In HI, the heater will be turned off when the seat gets warm; and be turned on again after the seat temperature drops. This process will repeat if only in HI..
F6 OWNER’S MANUAL BYD AUTO window: push the related switch one step downward and hold it, release it until the window gets to the desired position; or you can push the related switch two steps downwards and the window will lower down until it is fully open. To open any passenger‘s side window, push down the related switch and hold it, release it until the window gets to the desired position; to close the window, pull back the switch, release it until the window get to the desired position.
F6 OWNER’S MANUAL BYD AUTO Notice If you attempt to open the sun roof in the below-freezing temperature, or when it is covered with the snow or ice. The sun roof or motor may be damaged. Friendly tips Caution: Opening or closing the sun roof on the someone‘s hands or fingers can cause serious injury. Make sure everyone‘s hands or fingers are away from the sun roof before opening or closing the sun roof. The sun roof has the key-off delay function. The function can cancel when you open either front door.
F6 OWNER’S MANUAL BYD AUTO The system prompts drivers the distance between vehicles and obstacles by indicator and buzzer. A Distance (mm) Indicator Buzzer About l,200-800 Flash Intermittently buzz About 800-400 Flash Quickly intermittently buzz About 400 or less than 400 ON Continuously buzz Detecting Range The detecting range of the sensor is about l,200mm. Notice:The detecting area is limited, so you must check the surrounding before driving and get vehicle started slowly.
F6 OWNER’S MANUAL BYD AUTO The methods and steps to adjust interior rearview mirror: 1. Before adjusting, pay attention for the following three points: When the direction displayed by the interior rear view mirror is the vehicle head direction, the state is called normal display status.
F6 OWNER’S MANUAL BYD AUTO Exterior Power Adjustment Rearview Mirror You can adjust the exterior rearview mirror through adjustable knob on the door armrest of driver side. 1.Turn the ignition switch to the ON (Ⅱ) position. 2.Rotate the adjustable knob to the left (L) or right (R). Exterior Power Rearview Mirror Heater (optional) 3.You can adjust the rearview mirror to the left, right, up or down by pushing the adjustable knob in the corresponding direction.
F6 OWNER’S MANUAL BYD AUTO Parking brake When using the hand brake, pull the lever upwards fully. When loosing it, firstly pull it upwards lightly, and then press the release button and put the hand brake down. The indicator light of braking system on the instrument panel will be automatically turned off when the hand brake is released fully. Front Seat Armrest The buzzer will continuously buzz if you drive vehicle up to a speed when the hand brake is not released fully.
F6 OWNER’S MANUAL BYD AUTO Sunglass box CD Box Central Storage Box When opening the sunglass box, press its front edge. The sunglass box leaves the buckle and drops. When closing it, push it to the LOCK position. When driving, make sure the sunglass box is closed tightly. If you want to open the CD box, press the center of the box cover and make it leave the buckle, the box can be opened. When closing it, press the cover until it enters into the buckle.
F6 OWNER’S MANUAL BYD AUTO You can put some small objects into the groove of center storage box sleeve. When using the groove, pull the left rod and lift up the armrest cushion. Accessory Power Socket The socket is used to supply 12 volt DC power for the accessory that is rated 120 power or less. It can‘t supply power to the cigarette lighter. The cup holder for the front passengers lies in the center console.
F6 OWNER’S MANUAL BYD AUTO The bill box lies under of the vent. To open it, grab and pull its upper edge downwards. To close it, push it upwards. Sun Visor There are cup holders in the interior side of front and back doors. There is also cup holder in the back seat. It is in the center armrest. To use it, put it down. Bill Box To use a sun visor, pull it down. You can also use the sun visor for the side window: remove the support rod from the clip, and swing the sun visor toward side window.
F6 OWNER’S MANUAL BYD AUTO Vanity Mirror(optional) Cigarette Lighter Front Ashtray To use the vanity mirror in the sun visor, open its cover. The vanity mirror lights will be turned on when you open its cover. Only when turning the ignition switch to the ACCESSORY (Ⅰ) or ON (Ⅱ) position, the cigarette lighter can work. To heat it, push it in; it will be ejected automatically when it can be used. While heating, don‘t press it, or it will be overheated. To open the ashtray, open its cover.
F6 OWNER’S MANUAL BYD AUTO Rear Ashtray Interior Reading Light The rear ashtray lies in the back of the middle storage box. To use it, grab its top and pull down. To take out it to clean the ash, firstly open its cover, then lift. The rear interior lights have a three-position switch. In OFF, the light is not illumined. In the middle position (that is to open a door), if opening any door, the top light is on; after closing all the door, the light will get dark gradually and go out.
F6 OWNER’S MANUAL BYD AUTO In DOOR, Pull out the key from ignition switch, the light is on. If no door is opened, it will extinguish gradually. In DOOR, when you open the door by the key or remote transmitter (please refer to 27th page) the light will turn on. It will extinguish gradually after all doors are closed. Door light The ignition switch also has a spotlight. The Light will be on when opening the driver-side door. The light will extinguish gradually after closing the door.
F6 OWNER’S MANUAL BYD AUTO Central Air Outlet Side Air Outlet (optional) To adjust the direction of the center vent airflow, pull the adjusting handle up, down, right or left. You can open or close the air outlet through the rotary knob under the side air outlet.
F6 OWNER’S MANUAL BYD AUTO When the temperature is setted between (L0)and (HI),the temperature can be controlled to set temperature. OFF button Press the (OFF) button, and the interior air control system is closed fully. For avoiding the poor and moldy air cumulation, you should often keep the fan working. Semi-automatic mode operation In FULL AUTO, you can choose all function of interior air control system manually while keeping the other functions under automatic control.
F6 OWNER’S MANUAL BYD AUTO Interior/exterior air circulation switch The switch controls the air headstream entering into the system. When the circulation indicator is on, the air from the interior is circulated in vehicle again (interior circulation mode). When the indicator is off, the air will be brought in from the outside of vehicle (fresh air mode, or external circulation mode). For example, when the vehicle passes the area full of dust, you can set the system to interior circulation mode manually.
F6 OWNER’S MANUAL BYD AUTO Airflow from floor vents. Airflow is divided into the floor vents and the defroster vents at the base of windshield. Airflow is divided between the vents in the dashboard and the floor vents.
F6 OWNER’S MANUAL BYD AUTO Front windshield defroster switch Guide the main airflow to the windshield to defrost quickly. No matter what mode you Rear windshield defroster switch The button can open or close the rear windshield defroster. choose, the mode associated with button is priority. Outdoor temperature display button (OUT) Although the interior air control system is opened or no, press the button, and the display of passenger side will show the current outdoor temperature.
F6 OWNER’S MANUAL BYD AUTO Independent Temperature Control There are two knobs to control temperature in the vehicle, one for the driver, the other for passengers. When the green indicator on DUAL (independent control) button is on, it is allowed to independently adjust the temperature of driver side and passenger side by rotating the related knob. Notice:The indicator of the DUAL button will be automatically on when rotating the passenger side temperature control knob.
F6 OWNER’S MANUAL BYD AUTO Audio system (optional) Scan/Preview 64
F6 OWNER’S MANUAL BYD AUTO Audio system AM/FM The audio system can receive the AM and FM radio. You can expediently choose the favorite broadcasting station through the preset bar. Radio operation You can operate the radio only when the ignition switch is on the ACCESSORY (Ⅰ) or ON (Ⅱ) position. Turn the system on by pressing the (PWR/VOL) knob or AM/ FM button, rotate the (PWR/VOL) knob to adjust the volume. The bands and frequency that was last tuned will be displayed.
F6 OWNER’S MANUAL BYD AUTO Once the station is stored, you can press the left or right side of preset bar to listen to it. The frequency will be lost if the battery is discharged or disconnected, or the radio fuse is taken out. AUTO SELECT & SAVE (Hold SCAN)—Press SCAN for 2 seconds, the system will search the station and store it on FM1, FM2, FM3 or AM1, AM2. To activate it, long press the SCAN button. Then the SCAN is displayed in flashing.
F6 OWNER’S MANUAL BYD AUTO 1:30 will be enacted to 2:00 1:52 will be enacted to 2:00 Before don‘t set the time or battery is disconnected, or anew charge after power exhausted, the display of time will always twinkle to remind to set the time. USB/AUX input operation The system can play music of MP3 format in U disk through USB interface and play music through speaker-on board, and the music is from the input audio signal through AUX interface.
F6 OWNER’S MANUAL BYD AUTO Open the system once more, the phonograph will play from the last position. Press the quit button, take out the disc from the driver. If the disc has been quit, don‘t take out the disc at once, after 10 seconds, the system will introduce the disc automatically. To play the disc, press the CD button. When playing, use the (SEEK / SKIP) stripkey to choose the track and change the program. To quickly move the disc in the same program, press and hold the (SEEK / SKIP).
F6 OWNER’S MANUAL BYD AUTO Remote control (optional) When don‘t use the laser disc, put it into box to avoid being polluted. To prevent distortion, should avoid the overheating and the sun directly shining. When cleaning the disc, use the clean dishcloth from the center to edge. The inner and outer edge of the new laser disc is possibly some rough. The chipping of coarse edge will flake, if the chipping drop on the recorded face of disc will cause the skip or other malfunction.
F6 OWNER’S MANUAL BYD AUTO The (MODE) button can change the mode. Repeat to press the button, the system will circulate between the FM1, AM1 or disc playing (if have had the disc) or MP3 /WMV music playing (if the USB interface has been connected with the U disk) or the radio playing (if AUX interface has connected the player). Channel button ―∨‖―∧‖ has the same function with ―SEEK/SKIP‖ strip key.
F6 OWNER’S MANUAL BYD AUTO Cruise control system Cruise control system can keep the setting speed over 40 km/h and it isn‘t necessary to step the acceleration pedal. When driving on the erect and unblocked highway, you can use the function. Don‘t suggest using the function on the sinuous road, wet and slippery road, and rain day or at the condition of other bad climate as well as in the downtown. When encountering the condition, you should self-operate the vehicle.
F6 OWNER’S MANUAL BYD AUTO You can decrease the setting cruising speed in any of following ways. 1.Hold the (-/SET) button, the speed will be decreased. When reaching desired speed, release the button. 2.Push the braking pedal lightly, when reaching to the desired speed (over 40km/h), press the (-/SET) button. The vehicle will keep the desired speed. 3.To decrease the speed in a small amounts, repeat tap the (-/SET) button. Each time you do this. Your vehicle will speed down about 1.6 km/h.
F6 OWNER’S MANUAL BYD AUTO Before driving Before you begin driving the vehicle, you should know what gasoline to use and how to check the levels of important fluids. You also need to know how to properly store luggage or packages. The information in this section will help you solve these problems. If you plan to add accessories to your vehicle, please read the information in this section first. Running in period ........................... 74 Gasoline ..........................................
F6 OWNER’S MANUAL BYD AUTO Running in period Operation in petrol station During the first 1,000 kilometers, you should especially notice the method of driving. It‘s helpful to ensure the vehicle‘s future reliability and performance. Fuel tank filling Notice the following proceedings during this period: 1. Avoid full-throttle starts and rapid acceleration. 2. Avoid hard braking. New braking system need running-in through properly use in the first 300 kilometers. 3.
F6 OWNER’S MANUAL BYD AUTO Open engine hood To avoid losing the fuel fill cap carelessly, the fuel fill cap is attached to the fuel filler with a tether. When handling fuel, put the fuel fill cap on the bracket of fuel fill door. 1. Shift to Park or Neutral, and set the parking brake. Pull the hood release handle located under the lower left corner of the dashboard. The hood will pop up slightly. 4.Stop filling fuel to the tank after the fuel nozzle automatically clicks off.
F6 OWNER’S MANUAL BYD AUTO When closing the hood, lower the hood to about 30cm above the fender, and then firmly press down on the front edge of the hood. After closing the hood, you should inspect the latch whether it is securely latched. Ensure the engine preheating and park on the level ground. Wait three minutes after turning the engine off, and then check the oil level. 1. Pull out the dipstick.
F6 OWNER’S MANUAL BYD AUTO 2.Wipe the dipstick with a clean cloth or paper towel. Check engine coolant 3.Insert it all the way back in its hole. 4.Remove the dipstick again, and check the level. It should be between the upper and lower marks. If it is near or below the lower mark, refer to 103rd page on adding oil. BYD483QB the upper and lower marks of dipstick are two convex lines, and mark ―F‖‖L‖. The oil level should locate between the upper and lower.
F6 OWNER’S MANUAL BYD AUTO Driving custom Moderate driving is helpful to save fuel. Rapid acceleration, abrupt cornering and hard braking use more fuel. The air condition puts an extra loading on the engine which makes it use more fuel. Close the air condition to reduce fuel consumption. Use the fresh-air ventilation when air temperature out of vehicle is proper. Always drive in the highest gear possible, it can make the engine run and accelerate more stably.
F6 OWNER’S MANUAL BYD AUTO This vehicle has several convenient storage areas, it makes you carry the luggage safely. Glove box, door pockets, seat-back pockets is designed for storing small and light cargo, and trunk is used to carry big and heavy cargo. In addition, trunk channel port makes you carry long cargo in vehicle. However, carrying too much cargo or improperly storing, it can affect your vehicle‘s handling, stability and normal running, and reduce vehicle‘s safety.
F6 OWNER’S MANUAL BYD AUTO Driving Driving in atrocious weather ........... 90 Trailer .............................................. 91 This section gives you tips on starting the engine under various conditions, and how to operate the manual transmission and the automatic transmission. It also includes important information on parking your vehicle, the braking system and the vehicle‘s ABS. Driving preparation ......................... 81 Start engine .....................................
F6 OWNER’S MANUAL BYD AUTO Driving preparation You should do the following checks and adjustments before you drive your vehicle: 10. Turn the ignition switch to the position of ON (Ⅱ), and check the indicators in the instrument panel. 11. Start the engine (refer to 86th page). 1. Make sure all windows, mirrors and outside lights are clean and unobstructed. Remove frost, snow and ice stockpiling above. 2. Check that the hood and the trunk are fully closed. 3. Visually check the status of the tires.
F6 OWNER’S MANUAL BYD AUTO Start in high altitude (>2400m) cold weather The engine is hard to start in cold weather. Also, the engine is more hard to start in the thinner air found at altitudes above 2,400 meters. At this time, you should take following steps: 1. Turn off all electrical accessories to reduce the consumption of the battery. 2. Press the accelerator pedal halfway down, and hold it there in the whole process. The time that the key pauses on the START (III) position do not exceed 15 seconds.
F6 OWNER’S MANUAL BYD AUTO Max. permissible speed Automatic transmission These speeds correspond to max. permissible speed of every gear. If exceed these speeds, the engine speed display will enter into red area of tachometer. If this happens, you will feel the engine running intermittently, this is caused by safety governor in the ECU control device of engine. When you let the engine speed reduce below red area, the engine will recover normal running.
F6 OWNER’S MANUAL BYD AUTO Gear indicator is located on the left lower side of tachometer, show which position the shift lever is in (P, R, N, D; when it is in manual model and has speed, it can show the current using gear 1M, 2 M, 3 M, 4. to stop briefly with the engine idling. Shift to the Park position if you need to leave your vehicle. Press on the brake pedal when you are moving the shift lever from Neutral to another gear. Position of shift lever D:Drive—use this gear for your normal driving.
F6 OWNER’S MANUAL BYD AUTO increase until the transmission is in the hightest gear. Downshifting (-)—when normal driving and the shift lever is in the manual model, push the shift lever to this gear. After the control module of power assembly is able to judge according to the speed status, the transmission gear will correspond to decrease until the transmission is in the lowest gear. When parking, make sure to use hand brake.
F6 OWNER’S MANUAL BYD AUTO Shift to the Park position if you need to leave your vehicle. Press on the brake pedal when you are moving the shift lever from Neutral to another gear. P: Park; R: Reverse; N: Neutral; D: Drive; S: Sport; M: Manual. Position of shift lever D:Drive—use this gear for your normal driving. The transmission automatically selects suitable gear according to the vehicle speed and acceleration. You may feel the transmission shifting up at higher speed when the engine is cold.
F6 OWNER’S MANUAL BYD AUTO the highest gear (sixth). Downshifting (-)—when normal driving and the shift lever is in the manual model, push the shift lever to this gear. After the control module of power assembly is able to judge according to the speed status, the transmission gear will correspond to decrease until the transmission is in the lowest gear. When parking, make sure to use hand brake.
F6 OWNER’S MANUAL BYD AUTO 9 Make sure the hand brake whether it is fully released before driving away. Driving with the hand brake partially set can overheat or damage the rear brake. How to Drive Economically Select ―D‖ when driving on the wide road. Slowly step down the accelerator to assure the auto gear changes when the engine speed is relatively slow. Acceleration and Overtaking Step down the accelerator to the bottom quickly, which will activate the low-gear shift to switch to a proper gear.
F6 OWNER’S MANUAL BYD AUTO ABS ABS helps prevent the wheels from locking up or slipping when braking rapidly, so that make you retain steering control. When the front wheels are slipping, you will not do steering control, in other words, although turn the steering wheel, the vehicle still runs directly. ABS helps prevent from locking up, and because rapidly pulsatile-typed brake is quicker than person‘s reaction, it is helpful to retain steering control.
F6 OWNER’S MANUAL BYD AUTO ABS indicator ABS has the self-diagnosis function. If malfunction happens, the ABS indicator (refer to 88th page) on instrument panel comes on. This means that the ABS function of braking system has shut down. At this time, the brakes still supply common braking ability like a conventional vehicle without ABS. You should have BYD authorized service station to inspect your vehicle as soon as possible.
F6 OWNER’S MANUAL BYD AUTO When driving in the rain weather after long-term drought, you should be more careful. The first rain after long-term drought will make the oil plants float on the pavement, and lead to pavement wet and slip. Visibility—under all the weather conditions, it is very important to see far and near clearly, and be saw by other drivers. It is more difficult to do this point in the atrocious weather. To be seen more clearly, you should turn on the head light in daytime.
F6 OWNER’S MANUAL BYD AUTO Maintenance Periodical maintenance is the best method to protect vehicle, it can make you drive more safety, more economy, and no malfunction. This section will introduce the items which need periodical maintenance, and inspection method. Otherwise, it also introduces easy maintenance works in detail which you can complete by yourself. The periodical maintenance schedule will tell you when you should do these works. Battery ...........................................
F6 OWNER’S MANUAL BYD AUTO maintenance 2. On the allowable driving pavement, drive with limit speed by law. The periodical maintenance schedule lists out all the maintenance items what your vehicle need to keep it being in the best driving state all the time. Maintenance works should be according to the standard and specification of BYD AUTO CO., LTD., and be performed by mechanician of accepting formal training and conversance business.
F6 OWNER’S MANUAL BYD AUTO Oil and routine maintenance BYD F6 maintenance schedule and content: Odometer reading or months, whichever comes first Maintenance interval 1 ×1, 000 (km) 3 1 2 3 8 3 1 Maintenance items months 2 3 3 4 4 5 5 6 6 7 8 F 6 9 2 8 3 1 5 1 8 8 3 2 1 2 4 8 2 7 3 3 0 8 3 3 3 3 6 8 3 9 3 4 2 4 5 Engine and transmission 1.
F6 OWNER’S MANUAL BYD AUTO 5. Check the crankcase ventilation system (PVC valve and ventilation I I I I I I I I 6. Check coolant pipe I I I I I I I I 7. Check the liquid level in the reservoir I I I I I I I I 8.
F6 OWNER’S MANUAL BYD AUTO 18. Throttle control cable I 19. Throttle valve Clear every 10,000km 20. Injection nozzle I 21. Check oxygen sensor I I I I I I I I 22. Check three-way catalytic converter I I I I I I I I 23. Fuel filter Replace every 10,000km or every 6 months 24. Fuel tank cap, fuel lines and connections I 25. Charcoal canister I 26. Check and replace the gear oil in the AT case 27.
F6 OWNER’S MANUAL BYD AUTO 31. Brake pads and discs I 32. Brake fluid I 33. Brake pipes and hoses I 34. Power steering liquid I 35. Steering wheel, linkage I 36. Drive shaft dust boots I I I I I I I I I I I I I I I I I I I I I I I I I R I I I I R I I I I I I I I I I I I I I I I I I I I I I I I I I I I I I I I I I 37. Ball joints and dust covers I I I 38. Front and rear suspensions I I I 39. Tire and tire pressure I 40.
F6 OWNER’S MANUAL BYD AUTO 48. Check SRS airbag system I I 49.
F6 OWNER’S MANUAL BYD AUTO Remarks: (1)Symbol meaning in the schedule I=Check, correct or replace if necessary; R=Replace, change or lubricate; C=Clean. (2) Shorten the replacing time of oil filter according to the smudgy degree of oil. ―Serious condition‖ is following: (1)The vehicle is driving in dusty area, or the vehicle is at salty surrounding. (2)The vehicle is driving at accidental road, water road or hill road. (3)The vehicle is driving in the cold area.
F6 OWNER’S MANUAL BYD AUTO This periodical maintenance schedule roughly lists out the lowest limit maintenance items, and you must do them to protect you vehicle driving without malfunction. Because of the different areas and weather, it maybe needs to add some maintenance content. About more detail date, please refer to your warranty manual. Stated maintenance record Please let your BYD authorized service station fill all stated maintenance notes in the table.
F6 OWNER’S MANUAL BYD AUTO Engine oil Mitsubishi 4G69S4M engine oil filler cap Engine oil filling BYD483 engine oil filler cap When filling the engine oil, unscrew and remove the engine oil filler cap on top of the valve cover. After filling the engine oil, replace the engine oil filler cap, and tighten. Warm the engine, and then turn off. Three minutes later, recheck the oil level. Don‘t fill the oil above the upper mark, you could damage the engine.
F6 OWNER’S MANUAL BYD AUTO According to the graph as following, choose SAE viscidity oil which suit for your vehicle.
F6 OWNER’S MANUAL BYD AUTO Use the oil of saving fuel type which marks ―API repair grade or higher grade‖. This oil‘s formula is helpful to reduce fuel consumption of engine. Replace engine oil and oil filter Always replace oil and filter termly according to the recommended driving time and mileage in the periodical maintenance schedule. The oil and filter collect contaminants that can damage your engine if they are not removed regularly.
F6 OWNER’S MANUAL BYD AUTO Mitsubishi 4G69S4MS4M engine oil filter and oil drain plug stuck gasket could cause an oil leak. 5.Install a new oil filter according to the instructions that come with it. Make sure to clean off any dirt and dust on the connecting surface of a new oil filter. 6.Put a new washer on the drain bolt, then reinstall the drain boil and tighten it. Tighten torque: BYD483QB engine model 90 Nm Mitsubishi 4G69S4M engine model 39 Nm (4.
F6 OWNER’S MANUAL BYD AUTO Cooling system Engine coolant filling extender. If this coolant is not available, you may use another major-brand non-silicate coolant as a temporary replacement. Make sure it is a high-quality coolant recommended for aluminum engines. Otherwise, continued use any non-BYD coolant can result in corrosion, and cause the cooling system to malfunction or fail. So empty the cooling system as soon as possible, refill the antifreeze coolant of BYD AUTO brand.
F6 OWNER’S MANUAL BYD AUTO Pour the coolant slowly and carefully, so you do not spill any. Clean up any spill immediately. The spilled coolant could damage components in the engine compartment. Notice Do not add any rust inhibitors or other additives to your vehicle‘s cooling system. They may not be compatible with the coolant or engine components. Replace engine coolant Empty the coolant completely according to the recommended driving time and mileage in the periodical maintenance schedule.
F6 OWNER’S MANUAL BYD AUTO 5.Unscrew the drain coolant plug on the bottom of radiator. The coolant drains from bottom. Put it in a proper container. 6.Demount the assembly bolt of coolant reserve tank with wrench. 7.Get the coolant reserve tank down from bracket (pull from positive above), drain out the coolant and put it back, install the assembly bolt. 8.After emptying the coolant, screw down the drain coolant plug.
F6 OWNER’S MANUAL BYD AUTO 10.Run the engine about 30 seconds, and then turn it off. 11.Pour the coolant into radiator, till the level is up to the bottom of the filler neck.。 12.Pour the coolant into coolant reserve tank to the MAX mark, cover the cap. 13.Put the radiator cap back, and tighten to first stop position. 14.Run the engine itself, till the cooling fan at least starts two times, and then turn off the engine.
F6 OWNER’S MANUAL BYD AUTO Transmission oil Automatic transmission Check the oil level with the engine at normal operation temperature. 1.Drive the vehicle till the oil temperature is reaching the usual temperature (70~80℃). 2.Park the vehicle on level ground. 3.Change the shift lever to every position, make the oil inject into torque converter and hydraulic circuit, and then put the lever at N position, keep engine in normal idle speed, and must apply the park braking.
F6 OWNER’S MANUAL BYD AUTO 7.If the oil level is below the lower mark, remove the filler plug and add oil into the tube to make the level between upper and lower marks of HOT. Remark: status is the standard of measuring the transmission oil level, the level of cold engine is between upper and lower marks of COLD, only as reference. Pour the oil slowly and carefully so you do not spill any. Clean up the spill immediately, it could damage components in the engine compartment.
F6 OWNER’S MANUAL BYD AUTO If you are not sure how to check oil level and add oil, contact with BYD authorized service station. CVT transmission The transmission used is not filled with gasoline in advance, so you shall add ESSO EZL799A gasoline of 4.1±0.05 liter after the transmission is installed on the car.
F6 OWNER’S MANUAL BYD AUTO Oil Filling Screw Plug (3) the periodical maintenance schedule. Make sure to use BYD AUTO brake fluid, or same grade product DOT3 or DOT4 from a sealed container. The brake fluid marked DOT5 is not compatible with your vehicle‘s braking system, and brake fluid of different types does not mixed use. discs for abrasion. Clutch system (For manual transmission) Brake system Notes: be careful not to overflow the oil when filling for the accelerator.
F6 OWNER’S MANUAL BYD AUTO Power steering power steering fluid and make the fluid level up to the upper level. Notice Make sure to only use Mobil ATF DEXRON®-Ⅲ driving fluid, or ATF DEXRON-Ⅲ as power steering fluid, use other type power steering fluid will damage the power steering system. Pour the fluid slowly and carefully so you do not spill any. Clean up the spill immediately, it could damage components in the engine compartment.
F6 OWNER’S MANUAL BYD AUTO Air filter core Clean and replace the air filter core according to recommended driving time and mileage in the periodical maintenance schedule. 4.Install new air filter core into air filter case. 5.Reinstall the cover of air filter case, screw down four bolts. The air filter core installs in the air filter case on the driver side of engine compartment. Disassemble and reinstall according to replacing working process. Replacing 2. Disassemble old air filter core.
F6 OWNER’S MANUAL BYD AUTO Engine hood lock Spark plug (4G69S4M model) Replacing Replace vehicle‘s spark plug according recommended driving time and mileage in the periodical maintenance schedule. 1 . Clean up dunghill and oil crust aggregating around the ignition coil. 4.Get down the spark plug with spark plug sleeve. Use mellow detergent to clean the latch assembly of hood, and then wipe multipurpose lubricating oil. All active parts (showing as graph), including pivot, need to wipe lubricating oil.
F6 OWNER’S MANUAL BYD AUTO Notice Make sure to screw down the spark plug carefully. Spark plug too loose can damage the engine because of too hot; and too tighten can damage the thread on the head. 7.Install the ignition coil into the hole and push down to the bottom, assemble the bolt. 8.Connect the lead connector with ignition coil. Make sure to lock up on the position. 9 . Replace the other three spark plugs according to the steps above. Battery Check up the state of battery one time per month.
F6 OWNER’S MANUAL BYD AUTO Emergency dealing with Eye—— wash the eye at least for 15 minutes with water in cup or other container (pressure water will hurt your eyes), and cure. Skin—— take off the clothing polluted, wash skin with a great deal water, and cure. Drinking because of mistake—— drink the water or milk, and immediately cure. Check up the test indicator window on the battery to inspect the state of battery. There is the mean of all the color of test indicator window on the battery label.
F6 OWNER’S MANUAL BYD AUTO The methods of replacing blade: 1. Pull out the wiper arm from the windshield. Firstly pull out the wiper arm of driver side, then the passengers‘. 2. Press the locking button, disassemble blade assembly from the wiper arm. You should hold the blade assembly when push the blade assembly to the bottom of wiper arm. Notice Don‘t open the engine hood when pulling out the wiper arm or it will damage the engine hood and wiper arm.
F6 OWNER’S MANUAL BYD AUTO 4. Check up new blader, if it hasn‘t the plastic which cling to rear edge or metal strengthening plate, please take out the old blades‘ and fix it to new blade. 5.Slide the new blade into holder until the locking button is locked. 6.Assemble the blade assembly to wiper arm and make sure to lock it to desired position. 7.Put wiper arm to windshield. Firstly put the wiper arm of driver side, then passengers‘.
F6 OWNER’S MANUAL BYD AUTO The dust filter is at back of the glove box. 6.Assemble the new filter in the box sleeve. Make sure to properly locate BYD the ―LOGO‖ on the box sleeve. 1.Open the glove box. 2.Release the clasper of door side lieing in glove box of front passenger. 7.Finish the assembling of box sleeve. Make sure the both convex tongues lie in the right position. 8.Assemble the clasper of glove box, close it.
F6 OWNER’S MANUAL BYD AUTO 3. If it does not suit for the standard value, replace the tensioner. If it is out of the appropriate range, or found wear evidence, you should invite BYD authorized service station to replace it. BYD483QB engine adopts two multi-wedge belts. They are respectively used in driving generator and water pump, booster steering pump and A/C compressor. You should often check and adjust them.
F6 OWNER’S MANUAL BYD AUTO Timing belt Replace timing belt according recommended driving mileage in periodical maintenance schedule. to the Tire To safely drive your vehicle, your tires must be the proper type and size, in good condition with adequate tread and correct tire pressure. The following pages give more detail information on how to and when check the tire pressure, and how to check the damage and abrasion of tires, and the operation method when replacing tire.
F6 OWNER’S MANUAL BYD AUTO Inspection Every time you check tire charging condition, you should also examine the tires for damage, foreign objects, and abrasion. You should look for: 1. Damage and bulges in the tread or side of the tire. Replace the tire if you find either of these conditions. Your tires have wear marks molded into tread. When the tread wears down, you will see a band wide across the tread. This shows there is less than 1.6mm of tread left on the tire.
F6 OWNER’S MANUAL BYD AUTO Tire transposition The picture above shows how to change vehicle‘s tire position which doesn‘t have standard spare tires. When you buy and replace tires, you may find some tires are ―directional‖, this means this kind tire is designed into only one direction changing. If you use directional tires, they can only exchange front and rear wheels when changing tire position. If you use standard spare tires when changing position, please refer to the right picture.
F6 OWNER’S MANUAL BYD AUTO Replace tire and wheel The vehicle‘s original tires is chose to furthest play the vehicle performance, they can provide the best combination of handling, tire life and riding comfort at the same time. You should choose radial tires to exchange which have same size, load range, speed rating, and maximum cold tire pressure (marked on the side of tire). Mixing using radial and bias-ply tires can reduce braking ability, driving force (adhesive force) and steering accuracy.
F6 OWNER’S MANUAL BYD AUTO chains is quite worse. Some chains may also damage vehicle‘s tire, wheel, suspension and body. You should choose with chains to make enough free space between tire and other parts in the wheel cowl. Look over and read parts assembly graph and other instructions of chain factory carefully. Before you want to buy chains and install them on the vehicle, you should refer to BYD authorized service station.
F6 OWNER’S MANUAL BYD AUTO 2.Press the reed; pull out the connecter of electric device. 4.Pull out ground cable and power cable, press the clip reed and pull out it. Take out the bulb. 5.Replace the bulb, press the clip reed and push it into the fixed frame, and must make sure the bulb is locked. 6.Plug the power cable and ground cable, make sure they are fully connected, and don‘t loose. 7.Close the sealing cover. 3.Pull out the sealing cover.
F6 OWNER’S MANUAL BYD AUTO 3.Rotate out the sealing cover. Front position light 4.Pull out the ground cable and power cable, then press the clip reed and pull out it, and take out the bulb. 5.Replace the bulb, press the clip reed and push it into the fixed frame, make sure the bulb is locked. 6.Plug the power cable and ground cable, make sure it is fully connected, and don‘t loose. 7.Rotate in the sealing cover. 8.Connect the connecter of electric device; make sure it is well connected.
F6 OWNER’S MANUAL BYD AUTO 3.Pull out the sealing cover of high beam. 4.Contrarotate the mount of small light for quarter circle. Take out the small light. Front turning light 6.Fix the mount back to headlight assembly. Rotate it clockwise and make it locked to the proper position. 5.Take out and replace the bulb of small light. 7.Test the light to make sure whether the new bulb works normally. 6.Rotate small light clockwise, and make it reach to proper position.
F6 OWNER’S MANUAL BYD AUTO 2.Push the bottom cover. Replace rear turning light/reversing light/fog lamp 3.To disassemble the connecter of electric device from the bulb, push the both sides reed of connecter of electric device, and pull the connecter down. 4.Contrarotate bulb for quarter circle and disassemble it from front fog lamp assembly. 1.Disassemble the fixing bolt of bottom cover under front bumpe. 5.Fix the new bulb to front fog lamp assembly.
F6 OWNER’S MANUAL BYD AUTO Replace rear license plate light bulb 3.Contrarotate the mount for quarter circle, and disassemble it. 4.Directly pull out the bulb from the light mount. Fix new bulb. 5 . Anew fix the mount back to light assembly, rotate it clockwise until it is locked to proper position. 6.Test new bulb to make sure whether the bulb work normally. 7.Fix the interior trimming panel of trunk back to original place. 8.Push the interior trimming buckle into the hole.
F6 OWNER’S MANUAL BYD AUTO Push the interior trimming buckle into the hole. Replace reading light bulb and door light bulb Disassemble the door light and interior light with the same method. But they are different kinds of bulbs. Rear reading light: 1 . Prize the edge of lense light shield carefully, take out the light shield. Don‘t prize the edge of light shield protective jacket. 2.Take out the bulb from the metal clip jacket directly.
F6 OWNER’S MANUAL BYD AUTO Door light: Front reading lamp: Prize the front-edge of both sides reading lamp. Prize the up center of lense lignt shield.
F6 OWNER’S MANUAL BYD AUTO Replace trunk light bulb Vehicle storage If park your vehicle for a long time (over one month), refer to the following step. The step is useful to prevent vehicle from deteriorating and easy to rerun it. If possible, park it indoor. 1. Add fuel. 2. Replace the engine oil as well as filter (refer to 101st page). 3. Clean and dry the body thoroughly. 4. Clear the interior to make carpet dry. 1.Open trunk. 2.Underlay a piece of cloth to left side of trunk light assembly.
F6 OWNER’S MANUAL BYD AUTO Appearance maintenance Often washing and wiping your vehicle is useful to keep its appearance brand-new. The section will introduce how to wash your vehicle as well as how to keep its appearance clean (including paint, polishing, wheel and interior). Meanwhile there are some suggestions about anti-rust. Washing......................................... 135 Cere care ....................................... 135 Alloy wheel ................................... 136 Painting repair ..
F6 OWNER’S MANUAL BYD AUTO Washing Often washing vehicle is useful to its appearance. The dust and grit can hurt the paint, leaves and dung can damage the body finish permanently. Wash your vehicle in the cool place. Can‘t wash it in the sun. If park your vehicle in the sun for a long time, before washing it, drive it to the cool place, when it gets cool, wash it. Only use the solvent and cleanser which are recommended in the ―owner‘s manual‖.
F6 OWNER’S MANUAL BYD AUTO Alloy wheel When cleaning other exterior parts, meanwhile you should clean the alloy wheel. After cleaning them with the same solution, wash them thoroughly. There is a transparent protective layer to avoid aluminum eroding and rusting. The bad chemicals or hard brush will hurt the protective layer. Only use the neuter cleanser and soft brush or sponge to wash wheel. detergent can keep carpet like new. You should use bubble carpet cleanser.
F6 OWNER’S MANUAL BYD AUTO Nylon Vacuum the dust and ordure. Wash and wipe the nylon with soft cloth with neutral suds. Remove the harder ordure with the bristle brush with the same suds, also use spray or bubble nylon cleanser. Leather (optional) Vacuum the dust and ordure, especially the wrinkle and joint. Clean the leather with soft cloth dipping clean water, then, furbish it with dry cloth. If need further wash, use the special soap to wash, for example the leather cleaning soap.
F6 OWNER’S MANUAL BYD AUTO 1. Immediately repair when finding the dropping of paint and nick. 2. Check up and wash door as well as osculum under the body. 3. Check up the humidity of floor dress. The carpet and floor cushion will keep the humidity for a long time, especially in winter. Moisture will make the floor eroded. 4. Wash the body bottom with high pressure squirt gun. It is important for the vehicle which running on the road with proof-freeze salt in winter.
F6 OWNER’S MANUAL BYD AUTO Emergent solution malfunction Emergent Traction ......................... 156 CVT transmission: ........................ 157 This section includes some common problems that the driver often experiences when driving. And it will tell you how to judge and dispose correctly when you meet these problems. The problem has standed you on the side of road, you may be able to get going again according to the knowledge.
F6 OWNER’S MANUAL BYD AUTO Replace a flat tire If you have a flat tire while driving, stop in a safe place to change it. It‘s dangerous to stop in the center of road or at heavy traffic shoulder. Drive slowly along the shoulder until you get to an exit or an area that is far from the traffic lanes. Notice The vehicle can easily roll off the jack, seriously injuring anyone underneath. Make sure follow the directions for changing a tire exactly.
F6 OWNER’S MANUAL BYD AUTO Notice Use spare jack following vehicle. If you want to use the jack to lift other vehicles or use other jack to lift you vehicle, the jack or your vehicle may be damaged. 10.Remove the wheel nuts, make sure to be more careful while operating, the nuts may be hot from driving. 9.As shown, use the extension and wheel wrench to raise the vehicle until the flat tire is off the ground. 142 11.Remove the flat tire.
F6 OWNER’S MANUAL BYD AUTO 12.Before installing the spare tire, wipe any dirty off the installation surface of wheel and brake hub with a clean cloth. Wipe the hub carefully; it may be hot from driving. 13.Put on the spare wheel. Put the wheel nuts back and screw them lightly by hand, then tighten them in a crisscross pattern with the wheel nut wrench until the wheel is firmly against the brake hub. Do not try to tighten them fully. 143 14.Lower the vehicle to the ground, and remove the jack.
F6 OWNER’S MANUAL BYD AUTO 15.Tighten the wheel nuts seriously in the same crisscross pattern. Have the wheel nut torque checked at the nearest authorized service station. Tighten torque of wheel nuts: 108 Nm (11 kgf•m) 16.You need to remove the wheel‘s center cover before put the flat tire in the trunk. 17.Place the flat tire face down in the spare tire well. 18.Screw the wing bolt back to the flat tire‘s screw hole, and fix it.
F6 OWNER’S MANUAL BYD AUTO 19.Store the center cover in the trunk, make sure it does not get scratched or damaged. 20.Lower the trunk floor, and then close the trunk lid. If engine can’t start Diagnosing why the engine won‘t start falls into two areas depending on what you hear when you turn the ignition switch to the START (Ⅲ) position: 1. You hear nothing, or almost nothing. This means that the engine‘s starter motor does not operate at all, or operate very slowly. 2.
F6 OWNER’S MANUAL BYD AUTO Pushing car to start engine (for model with manual transmission) If the vehicle‘s battery is discharged, maybe you can use a booster battery to start the engine. Although this seems like a simple procedure, you would take several precautions. Friendly tips A battery can explode if you do not follow the correct procedure, seriously injuring anyone nearby. Make sure to keep all sparks, open flames and smoking materials away from the battery.
F6 OWNER’S MANUAL BYD AUTO 7.Once your vehicle is running, disconnect the negative cable from your vehicle, then from the booster battery. Disconnect the positive cable from your vehicle, then from the booster battery. Keep the ends of the jumper cables away from each other. At the same time, keep the ends of the jumper cables away from any metal on the vehicle until everything is disconnected. Otherwise, you may cause an electrical short.
F6 OWNER’S MANUAL BYD AUTO steep hill with the A/C opening in the hot day), the engine should start to cool down almost immediately. At this time, wait until the coolant temperature gauge comes down to the midpoint, and then continue driving. reaches the middle of the temperature gauge, or lower, before checking the radiator. Friendly tips 5.Open the hood until you do not see any steam or spray coming out.
F6 OWNER’S MANUAL BYD AUTO The indicator is on when turning ignitions witch to ON (Ⅱ). The indicator is off after starting engine. And indicator is off within engine working. If it twinkles, show oil pressure descends too fast instantaneously, but get normal once more. If the indicator is always on within engine working, show it has hadn‘t oil pressure and engine may have a serious hurt. Whatever above any symbol happens, should take measures immediately.
F6 OWNER’S MANUAL BYD AUTO Engine malfunction indicator drive at a high speed. If the indicator is frequently on, even if close it according to the above step, it is necessary to call BYD authorized service station for repairing. The indicator will be on when turning ignition switch to ON (Ⅱ). It reminds you to check up the parking handle. If you don‘t fully put it down, the indicator will be always on. Friendly tip If go on driving vehicle when the malfunction indicator is on.
F6 OWNER’S MANUAL BYD AUTO Shift to low gear to decelerate, and park your vehicle at the road. Because of the long brake distance, drive is dangerous. Trail the vehicle and repair it as soon as possible. (Refer to 162nd page about urgent draught). If you have to drive for a short distance at the state, be sure to carefully drive at a low speed. 5.Insert the wrench into sleeve of embolism, rotate wrench until the sun roof is fully closed. 6.Pull out wrench, fix the round embolism anew.
F6 OWNER’S MANUAL BYD AUTO The interior fuse box is under the driver side. To disassemble it, pull and take out it from hinge. reason for malfunction, should check up all fuses. Replace all burned fuses and check up the work state of all electric devices. 1.Turn ignition switch to LOCK (0), make sure the headlight as well as other accessory have been closed. 3.Measure both ends of fuse with the lead gear of multimeter.
F6 OWNER’S MANUAL BYD AUTO having malfunction and hasn‘t the spare fuse to replace, pull out the fuse, it has a same aph value or lower from other circuitry, instead of it. But firstly you must make sure the circuitry (cigar lighter or radio) has no influence on drive. The replaced spare fuse may be burned once more. Though it doesn‘t show that there is malfunction, also you should use the fuse which has right rating value to replace as soon as possible.
F6 OWNER’S MANUAL BYD AUTO Use box under engineer hood Label of fuse box The position of fuse is marked on the fuse label by the number. Refer to the page about the fuse on your vehicle.
F6 OWNER’S MANUAL BYD AUTO Number 1 2 3 4 5 6 AMP 10A 10A 10A 10A 30A 15A 7 8 7.5A 20A 9 15A 10 30A 11 20A 12 7.
F6 OWNER’S MANUAL BYD AUTO Interior fuse box Label of fuse box The position of fuse is marked on the fuse label by the number. Refer to the page about the fuse on your vehicle.
F6 OWNER’S MANUAL BYD AUTO Number 1 Amp 20A Device or circuitry protected Door lock, trunk lock motor power 2 7.5A 3 10A Door light, environment light, roof light, map light, trunk light, dresser light Instrument control module, combination switch control device, door multi roads control, (MICU) 4 10A Radio system power 5 15A Cigar lighter, spare power 6 7.
F6 OWNER’S MANUAL BYD AUTO Notice If your BYD vehicle can not use Flat-bed Equipment to transport, you should use Wheel-lift Equipment to transport. If, due to damage, your vehicle must be towed with the front wheels on the ground, do the following: Manual transmission: 1 Release the parking brake. 2 put the transmission in Neutral. 3 Leave the ignition switch in the ACCESSORY (Ⅰ) position, so the steering wheel does not lock. Automatic transmission: 1 Release the parking brake. 2 Start the engine.
F6 OWNER’S MANUAL BYD AUTO Notice Notice Improter towing preparation will damage thetransmission. So follow the above procedure exactly. If you can not shift the transmission or start the engine (AT), your vehicle must be transported with the front wheels off the ground. The steering system can be damaged if the steering wheel is locked. Leave the ignition switch in the ACCESSORY (Ⅰ) position, and make sure the steering wheel turns freely before you begin towing.
F6 OWNER’S MANUAL BYD AUTO Technical data Diagram of the chapter shows the dimension and capacity as well as the position of identification no. Identification No. ......................... 160 Specification ................................
F6 OWNER’S MANUAL BYD AUTO Identification No. There are several identification no. at different positions on your vehicle. 1.The engine model no. is stamped in the Engine group. 2.The transmission no. is in the name plate at the top of the transmission. Don‘t confuse the transmission no. and engine no..
F6 OWNER’S MANUAL BYD AUTO Engine Model CVT Transmission No. 3.Vehicle identification no. (VIN) marked on the rear clapboard of engine chamber and the label on the instrument of left –down position of front windshield. 4.Product label is nailed on the left damper mounting. There are (VIN), engine no., vehicle no., displacement, the main designer and the date of producer etc.
F6 OWNER’S MANUAL BYD AUTO Specification Diameter×Stroke Dimension Displacement Length Width Height Wheelbase Track 4846mm 1822mm 2.0 2.4 2.0 2.4 Front Rear 1465mm Compression ratio 2.0 2.4 2.0 2.4 2.0 2.4 2740mm 1551mm 1551mm Spark plug 83×92mm 87×100mm 1.991 2.378 9.6:1 9.5:1 Refer to section about maintenance of spark plug on 98th and 118th page. Quality Unladen Mass Max Permitted Mass MT CVT 2.0L 2.4L MT CVT 2.0L 2.
F6 OWNER’S MANUAL BYD AUTO Tire Steering Dimension/tire pressure Please look at the data label on the driver side door case or refer it from BYD AUTO authorized service station.
F6 OWNER’S MANUAL BYD AUTO Three-way catalytic converter Meet the following displacement standard: •GB18352.2-2001 Light vehicle displacement limited value & measure method (Ⅱ) •GB18352.3-2005 Light vehicle displacement limited value & measure method (Ⅲ) Three-way catalytic converter includes precious metals which is a catalyze and accelerate the chemical reaction to purify exhaust gas, but the metal hasn‘t been affect.