INSTRUCTIONS FOR C-giant . . by Coralba Sweden . 1 2 3 TRIP1 TRIP2 SPEED 4 5 6 FUEL PILOT 8 9 TIME -giant ADD 7 BREAK HALT SPLIT SET 0 CAL OPTION RESET Option: C-view by Coralba Sweden . BACK NEXT Jemba ab Väpnarv. 10, SE-691 53 KARLSKOGA, Sweden Tel: +46-(0)586-55640, Fax: +46-(0)586-31451 www.jemba.se, E-mail: info@jemba.
C-giant rel 3.07. Sales by Jemba, Sweden. Tel +46 (0)586 55640 TABLE OF CONTENTS Page TABLE OF CONTENTS ..................................................................................................................... 2 1. GENERAL ....................................................................................................................................... 3 2. FITTING C-GIANT .......................................................................................................................
C-giant rel 3.07. Sales by Jemba, Sweden. Tel +46 (0)586 55640 1. GENERAL Edition 28 September 2005 C-giant is used for measuring during rallies. It is an indispensable instrument for the professional co-driver. The instrument has been developed by Corabla after many years of experience of a co-drivers special needs in his stressful situation. Therefore Cgiant has all the functions that will make a co-driver perform his duties RAPIDLY, SECURELY and EFFICIENTLY. by Coralba Sweden . . .
C-giant rel 3.07. Sales by Jemba, Sweden. Tel +46 (0)586 55640 2. FITTING C-GIANT 2.1. Fitting the instrument Fitting the C-giant into the vehicle is extremely simple. First you have to fit the instrument itself. Fitting of C-giant in the vehicle compartment is done with its two fastening bolts (M4x10) at the back of the unit. The bolts may be exchanged to any other M4 bolts providing they are the same length. 2.2.
C-giant rel 3.07. Sales by Jemba, Sweden. Tel +46 (0)586 55640 2.3. Electrical connections Make sure great care is taken in connecting C-giant as damage may occur to the unit if it is connected incorrectly. The system should have negative ground. • • • • • Red cable (power) is connected to +12 volt directly from the battery through a fuse of about 1 A. Brown cable is connected to the negative pole directly on battery.
C-giant rel 3.07. Sales by Jemba, Sweden. Tel +46 (0)586 55640 2.3.1. Connections for yellow remote control The yellow cable is meant to be +12 volt connected to the reverse light as default to reverse counting when the vehicle is < 10 kOhm Yellow remote control reversed. However for a rallycar it is Yellow cable more convenient to use it as a second remote control (See page 25). For this reason the remote control for the yellow cable can not be connected in the same way as for the white remote cable.
C-giant rel 3.07. Sales by Jemba, Sweden. Tel +46 (0)586 55640 4. FUNCTION The panel has three display windows: • The main display with six figures • Upper left and lower left displays with four figures each. The keyboard has four different kinds of keys: • Selector keys: TRIP 1, TRIP 2, SPEED, TIME, FUEL, PILOT, CAL, OPTION which will select different registers and display its value in the main display. • Operator keys: SET, ADD/-, HALT, +, RESET which will operate on the value in the selected register.
C-giant rel 3.07. Sales by Jemba, Sweden. Tel +46 (0)586 55640 . 4.2. Summary of functions C-giant has the following functions: Key by Coralba Sweden . . -giant .. . .MEMory . TRIP 2 .triP..2 .. . .SS.Hour . . .A.SPEEd .. .toP.SPd . . .EtA.diS . . .EtA.-A. . . . .EtA.Cur . Page 8 . 2 3 TRIP1 TRIP2 SPEED 4 5 6 TIME ADD BREAK 7 HALT FUEL PILOT 8 9 SPLIT SET 0 CAL OPTION RESET Function Appropriate keys Trip meter with a resolution of l metre See page 11.
C-giant rel 3.07. Sales by Jemba, Sweden. Tel +46 (0)586 55640 . . Key by Coralba Sweden . -giant BREAK Flash text . . SPEED .SPEEd. . . .triP..3 .. . .SPd.thr . . ARROW UP .SELEct. . .ShiFt.1 . 3 TRIP2 SPEED 4 5 6 7 HALT FUEL PILOT 8 9 SPLIT SET 0 CAL OPTION RESET Appropriate keys Calibrate distance if trip or speed is selected. SET, SPLIT, Second touch will show ".CALib." in display RESET and then ".drivE." telling to drive reference length.
C-giant rel 3.07. Sales by Jemba, Sweden. Tel +46 (0)586 55640 Key Function Appropriate keys Calibrate time if time is selected. SET, Flash text (TIME)+CAL .CALib. RESET . . -, +, See page 22. FUEL ..FUEL. .. . (FUEL)+CAL .CALib. . CAL, SPLIT, -, + Calibrate Fuel if fuel is selected. See page 22. SET, RESET Time ahead or delayed in respect to the scheduled average speed. Scheduled speed is set in the SPEEd-mode. See page 12. SET, -, HALT, +, SPLIT, RESET . PILOT ..Pilot. ..
C-giant rel 3.07. Sales by Jemba, Sweden. Tel +46 (0)586 55640 . . by Coralba Sweden . -giant 1 2 3 TRIP1 TRIP2 SPEED 4 5 6 TIME ADD BREAK 7 HALT FUEL PILOT 8 9 SPLIT SET 0 CAL OPTION RESET 4.2.1. TRIP l, TRIP 2, TRIP 3 Registers with a resolution of l metre . Press the appropriate key to select and see value, and to change its function. Flash text (.triP..1) and a led indicator shows that the function is selected.
C-giant rel 3.07. Sales by Jemba, Sweden. Tel +46 (0)586 55640 This function may be used together with TRIP l (.trip..1), TRIP 2 (.trip..2, .EtA.diS, .EtA.-A.), SPEED (.triP..3, .SPd.thr), TIME (.Hour..1, .Hour..2), PILOT (..Pilot.), CAL (.CAL.diS). Selectable keys: numeric keys, -, RESET. 4.2.5. TIME TIME has two time registers which may act as an ordinary clock or a stop watch. They can count forwards and backwards. Flash text (.Hour..1) or (.Hour..2) and led indicator show which function is selected.
C-giant rel 3.07. Sales by Jemba, Sweden. Tel +46 (0)586 55640 If CAL is used when FUEL is selected a sequence is started that will calibrate the FUEL function. See page 22. Flash text (.CALib.) and led indicator show that the function is selected. Selectable keys: SET, numeric keys, RESET. . . by Coralba Sweden . -giant 1 2 3 TRIP1 TRIP2 SPEED 4 5 6 TIME ADD BREAK 7 HALT FUEL PILOT 8 9 SPLIT SET 0 CAL OPTION RESET 4.2.10. BREAK BREAK will reset the instrument to a defined status.
C-giant rel 3.07. Sales by Jemba, Sweden. Tel +46 (0)586 55640 . . by Coralba Sweden . -giant 1 2 3 TRIP1 TRIP2 SPEED 4 5 6 TIME ADD BREAK 7 HALT FUEL PILOT 8 9 SPLIT SET 0 CAL OPTION RESET 4.2.14. SPLIT SPLIT will freeze all registers values simultaneously permitting later inspection. All functions will carry on their counting. Flash text (..SPlit.) and led indicator shows that the function is selected. Second touch at 'SPLIT' will disable the freeze function and show current values.
C-giant rel 3.07. Sales by Jemba, Sweden. Tel +46 (0)586 55640 5. OPERATION 5.1. Distances measurement (Trip l, Trip 2 and Trip 3) When measuring distances C-giant has got three registers for this purpose, TRIP l, TRIP 2 and TRIP 3. They may be used individually with separate counting directions plus (+) or minus (-). 'HALT' will stop the current register. 'SPLIT' freezes the values of all registers. If the measurement is to be done in the negative direction you just press the (-) key.
C-giant rel 3.07. Sales by Jemba, Sweden. Tel +46 (0)586 55640 5.1.4. Automatic measurements on special stages (SS) By repeated pressing on 'TRIP 2' you will get access to a number of registers that will give you automatic measurements on special stages. This is a great relief for the codriver at the start and finish of special stages. By resetting TRIP 2 the automatic measurement of the length, time, top speed and average speed is initiated.
C-giant rel 3.07. Sales by Jemba, Sweden. Tel +46 (0)586 55640 . . by Coralba Sweden . -giant 1 2 3 TRIP1 TRIP2 SPEED 4 5 6 TIME ADD BREAK 7 HALT C-giant shows SET 0 FUEL PILOT 8 9 SPLIT CAL OPTION RESET Action Flash text Shown format TRIP 2 .triP..2 TRIP 2 .SS.Hour TRIP 2 .A.SPEEd TRIP 2 .toP.SPd TRIP 2 .EtA.diS Length of current road section xxx.xxx TRIP 2 .EtA.-A. Estimated time of arrival for Average speed calculated from .EtA.diS, .triP..2 and .A.SPEEd xx.xx.
C-giant rel 3.07. Sales by Jemba, Sweden. Tel +46 (0)586 55640 5.3. Set As mentioned previously SET is used to set any register to a desired value. The register to be set is selected by pressing the appropriate key and thus making it visible in the display. To set the value simply press SET and you will see the figures in the display flash. This indicates that by using the numeric keys you may enter a new value. A negative value may be entered by preceding the value with (-).
C-giant rel 3.07. Sales by Jemba, Sweden. Tel +46 (0)586 55640 5.4.1. Set time Action C-giant shows Press TIME (select TIME register) Current time Press SET (start input of value) Current time flashes Set time with numeric keys 0 to 9 New time flashes Press SET (store with SET-key) New time 5.4.2. Adjust time It is very easy to adjust the time by any value: The same procedure as for trip meters is valid. For time the format of 24.59.59 is taken into account automatically.
C-giant rel 3.07. Sales by Jemba, Sweden. Tel +46 (0)586 55640 5.6. Monitoring average speed (PILOT) The Pilot is a useful tool to monitor your actual position in respect of the scheduled time. This is important when the road sections are long or some service is required on the car. By storing the required average speed into the SPEED register the time gained or time delayed is read in the PILOT register. The sequence is: . . by Coralba Sweden .
C-giant rel 3.07. Sales by Jemba, Sweden. Tel +46 (0)586 55640 back and it will give you the correct penalty for your mistake. Don't forget to set it back to the (+) direction once you are back on the correct route again! The PILOT calculates continuously the time gained or time delayed in respect to the stored average speed. If you are delayed the result is shown with a "-" in front of the time value. The format of the result is hour.min.sec (hh.mm.ss). 5.7.
C-giant rel 3.07. Sales by Jemba, Sweden. Tel +46 (0)586 55640 You have now calibrated your C-giant for distance and speed. If the calibrating constant is greater than 100 000 you should contact your supplier to get a different interface for your speed signal. The display mode may be changed as described at page 24 without calibrating the system again.
C-giant rel 3.07. Sales by Jemba, Sweden. Tel +46 (0)586 55640 Action C-giant shows Press FUEL uncalibrated amount of fuel Press CAL .C.Pnt-1 flashes Press SET 0 flashes Input current amount of fuel in the tank. As the tank is almost empty you feed a "0" 0 Press SET .C.Pnt-2 flashes Fill about ten litres. Press SET xx flashes Feed the current amount of fuel in the tank (10) 10 Press SET .C.Pnt-3 flashes Fill about another fifteen litres.
C-giant rel 3.07. Sales by Jemba, Sweden. Tel +46 (0)586 55640 5.10. Set up units in C-giant You may select different units for distance and speed in a special set up mode. Also the communication for a -giant printer (option) may be set. From factory the unit is set up to the standard setting for your market. If you want to change units it is important to have your desired units set up before the calibration takes place.
C-giant rel 3.07. Sales by Jemba, Sweden. Tel +46 (0)586 55640 miles + yards feet nautical miles miles + feet (Mil.yArd) (FEEt) (nAutMil) (MiL.FEEt) SPEED (selection key is 'SPEED'): kilometres per hour (kiloM/h) miles per hour (MPH) metres per minute (M/Min) feet per minute (Ft/Min) knots (knotS) metres per second (M/SEc) For the connection of a printer or a computer (option) the set up of the communication may be of interest: BAUD RATE (selection key is '+'): br.
C-giant rel 3.07. Sales by Jemba, Sweden. Tel +46 (0)586 55640 5.12. Option C-giant has got two remote lines (yellow and white cable) that may be used with default functions or with definitions made by the user. See page 5 and 6 on how to connect. 'OPTION' lets you define the functions for these control lines. The indicator in the key is on when at least one remote line is defined by the user.
C-giant rel 3.07. Sales by Jemba, Sweden. Tel +46 (0)586 55640 Example 1: Finish of special stage At the finish of a special stage it is convenient to have a remote control defined to perform the following functions: Freeze, select time on stage, select time of day and select maximum speed. Just press the following keys. Press Result Display OPTION OPTION SET SPLIT Show selected remote line Show selected remote line Starts the definition for the yellow remote Will split the instrument .WhitE .
C-giant rel 3.07. Sales by Jemba, Sweden. Tel +46 (0)586 55640 Example 2: Road section interval During a road section it is convenient to have a remote control defined to perform the following functions: Reset and show interval distance, show total distance, select and show estimated time of arrival to next time control with 10 s resolution. Just press the following keys.
C-giant rel 3.07. Sales by Jemba, Sweden. Tel +46 (0)586 55640 6. ERROR CODES AND TROUBLESHOOTING On some occasions an error code may appear in the display. The following codes are available: Code . Reason Action to be taken Voltage from the fuel sender was Check connections for the black cable. unchanged for two calibration The power supply must be ON to the points during fuel calibration. fuel sender (Ignition key ON). . . Probably a bad connection for the power supply.
C-giant rel 3.07. Sales by Jemba, Sweden. Tel +46 (0)586 55640 7. INDEX -, 13 +, 13 accident, 6 accuracy, 22 Ad.