Installation manual

ManualsBrandsC&K systems ManualsHome building and DecorSystem 238

SYSTEM 238 Installation Manual

BLK

RED

BATTERY

DIRECT

CONNECT

DEVICES

UNSWITCHED

AUX

POWER

- Protected by Fuse F2:

3 AG, 0.75 A

- Shared with keypads

and AUX POWER

KEYPAD

INFORMATION

- Do not exceed 4

keypads

or max AUX POWER

- Protected by Fuse

F3: 3 AG, 0.75 A

WARNINGS:

- For continued protection

against risk of fire, replaces

fuses only with fuses of same

type and rating

- Disconnect AC, battery, and

phone cord BEFORE servicing

2.2K

EOL

2.2K

EOL

2.2K

EOL

2.2K

EOL

2.2K

EOL

2.2K

EOL

2.2K

EOL

2.2K

EOL

Capacity for

emergency standby

at least 4 hours

- Connect ground wire from door hinge to earth ground using

16 AWG, green jacketed, solid-conductor wire

GENERAL INFORMATION

- All outputs are power limited

- If programmed for EOL or Supervised loop, the 2.2K ohm EOL

resistor (Model 9.X, 2.2K) must be at end of circuit

- Loop 8 can be used as standard loop or used for switched 10-

12.5 VDC at 50 mA for 2-wire powered devices. Loop 8 can

support up to 10 BRK Model 2400 2-wire smoke detectors.

- Loop voltages:

Loops 1 - 8

0 - 2.5 VDC = short

2.5 - 8.5 VDC = normal

8.6 - 15 VDC = open

- Install transformer on unswitched power receptacle

- Only use 12 VDC, 6.5 AH sealed lead-acid battery

POWER SUPPLY INFORMATION

- Replace battery every 3 - 5 years with C&K Model 1265

- Standby time with 1 keypad is 16 hours at 250 mA

- Power demand for AUX POWER, keypads, and sounders

not to exceed maximum ratings

Fuse F4

3 AG, 3 A

battery protection

- are electrically common

AUDIBLE

10.5-13.5 VDC

Protected by Fuse

F1: 3AG, 2.5 A

16.5 VAC

25 - 40 VA

50 / 60 Hz

SWITCHED

AUX

POWER

P/N 5-051-162-00 Rev K

PHONE

CORD

- 9.X PCF

Red = incoming ring

Green = incoming tip

Gray = seized ring

Brown = seized tip

Blue = tamper

Orange = tamper

WARNING: Circuit Damage May Result

From Incorrect Wiring Connections.

- Remove AC and battery power before replacing fuses

- Maximum battery charge current = 350 mA

CAUTION:

Total power from Bell, Sw/Aux, Aux

and Key+ Terminals NOT to exceed

800 mA, combined

12 VDC

6.5 AH

sealed lead-acid

F2 0.75 A

KEYPAD

F1 2.5 A

BELL FUSE

F2 0.75 A

AUX DEVICES

Summary of content (28 pages)

PAGE 1
SYSTEM 238 Installation Manual BATTERY WARNINGS: F2 0.75 A KEYPAD F2 0.75 A AUX DEVICES BLK F1 2.5 A BELL FUSE DIRECT CONNECT - For continued protection against risk of fire, replaces fuses only with fuses of same type and rating RED - Disconnect AC, battery, and phone cord BEFORE servicing WARNING: Circuit Damage May Result From Incorrect Wiring Connections. Capacity for emergency standby at least 4 hours PHONE CORD DEVICES 2.2K EOL 16.
PAGE 2
SYSTEM 238 Installation Manual Table of Contents Subject System 238 Terminal Label Residential and Commercial Installation Guidelines Installation Wiring the Panel System Start-Up Keypad Setup Addressing Keypads Factory Default Settings Programming Options (Alphabetical List) Programming the Panel Programming with the LED Keypad Programming with the Alpha Keypad Entering Hexadecimal Numbers Programming the Alpha Keypad Programming Letters & Numbers Special Function Keys Programming Options (Numerical Order
PAGE 3
SYSTEM 238 Installation Manual Earth Ground To ensure the effectiveness of the lightning and transient protection circuits, the control panel must be connected to "Earth Ground". Ideally, this should be a common ground to the power lines, telephone system, and security system. This type of ground, called a "Unified Earth Ground", provides the best protection.
PAGE 4
SYSTEM 238 Installation Manual TAMPER SWITCH INSTALLATION Keypad Wiring C&K has designed the SYSTEM 238 cabinet to use the Ademco Model 19 tamper switch. The cabinet is constructed in order to accommodate two switches. One tamper for the cover and a second switch for a wall tamper. To install the tamper switches: 1. Position the tamper switch inside the cabinet at the lower right corner of the cabinet. For the wall tamper, the plunger should go through the small hole in the back of the cabinet.
PAGE 5
SYSTEM 238 Installation Manual FACTORY SETTINGS 9.X PCF The 9.X PCF has eight flying leads. Wire them to the PCB terminals as follows: RED = ring BROWN = tip seized GREEN = tip BLUE and ORANGE = tamper GRAY = ring seized YELLOW and BLACK = not used DEFAULT PROGRAM SETUP The default programming of the SYSTEM 238 will allow you to operate it as a local panel without any additional programming. The actual default programming values are shown on the Programming Worksheet (last 2 pages of this manual).
PAGE 6
SYSTEM 238 Installation Manual Option Combination Command Daily Battery Test Enable Delay Before Dial by Loop Delay Before Dial Time Dial Attempts Dial Type Disable Loop LEDs Door Chime Enable by Loop Duress Report Code Duress Report Receiver Emergency Bell Type Emergency Report Code Emergency Receiver Select Entry Delay Time Entry Pre-alarm Enable Exit Delay Time Exit Pre-alarm Enable Faulted Arming Type Fire Bell Type Fire Report Code Fire Receiver Select Four Minute Power Up Delay Enable Group Shunt Ena
PAGE 7
SYSTEM 238 Installation Manual The Scrolling order of the Alpha Plus messages is: PROGRAMMING CONVERSIONS Hexadecimal Value A B C D E F Key Strokes SERVICE MESSAGE 0 1 2 3 4 5 DEALER MESSAGE SOFT ZONE IDENTIFIER (C) HARDWIRED LOOP IDENTIFIERS KEYPAD ADDRESS Both the Alpha and the Alpha Plus use the same procedure to program messages. PROGRAMMING the ALPHA KEYPAD ALPHA II Programming Template Ensure the Alpha keypad is wired to the SYSTEM 238 and power is applied to the control panel.
PAGE 8
Command Locations 00 - 08 SYSTEM 238 Installation Manual Command Location 00: Installer Combination Default Values 0 0 0 1 2 3 4 5 0 (1) (2) (3) (4) (5) (6) 4 E Digit Position (1): First Digit of Installer Combination Hard-coded to "0". Installer's combination will always start with 0. Digit Positions (2) - (6): Remaining Digits in Combination Combination must have 5 digits in addition to Position (1). Valid entries are 0 - 9.
PAGE 9
Command Locations 09 and 0A SYSTEM 238 Installation Manual Command Location 09: Arming/Combination Options Default Values 0 0 1 1 9 Digit Position (1): Guest Combination Time 0 = Guest Time Disabled 1 = 1 day 2 = 2 days 3 = 3 days 4 = 4 days 0 (1) (2) (3) (4) 1 2 1 2 0 = 10 days 1 = 11 days 2 = 12 days 3 = 13 days 4 = 14 days 5 = 15 days 5 = 5 days 6 = 6 days 7 = 7 days 8 = 8 days 9 = 9 days Digit Position (2): Combination Command 0 = No 1 = Yes; requires combination for Bypass, Group
PAGE 10
Command Locations 0B and 0C SYSTEM 238 Installation Manual Command Location 0B: Communications Control Default Values 0 0 Digit Position (1): 0 = 0 secs 1 = 10 secs 2 = 20 secs 3 = 30 secs 8 = 80 secs 9 = 90 secs 0 = 100 secs 1 = 110 secs 1 1 0 8 B Delay Before Dial Time 4 = 40 secs 5 = 50 secs 6 = 60 secs 7 = 70 secs 3 (1) (2) (3) (4) (5) (6) 0 0 0 0 0 0 2 = 120 secs 3 = 130 secs 4 = 140 secs 5 = 150 secs Digit Position (2): Dial Type 2 = DTMF (5/sec) 1 = DTMF - Touch Tone (1
PAGE 11
Command Locations 0D - 10 SYSTEM 238 Installation Manual Command Locations 0D - 0F: Receiver #1 Phone Number Order in which the numbers will be dialed Command Location 0D (1) (2) (3) (4) (5) Command Location 0E (6) (1) (2) (3) (4) (5) Command Location 0F (6) (1) (2) (3) (4) (5) (6) Command Location 0D: Receiver #1 Phone Number (digits 1 - 6) Default Values E 0 0 0 0 0 0 D (1) (2) (3) (4) (5) (6) Digit Positions (1) - (6): 0 - 9 = dialing digits 0 = dial tone detect 2
PAGE 12
Command Locations 11 - 13 SYSTEM 238 Installation Manual Command Locations 11 - 13: Receiver #2 Phone Number Order in which the numbers will be dialed Command Location 11 (1) (2) (3) (4) (5) Command Location 12 (6) (1) (2) (3) (4) Command Location 13 (5) (6) (1) (2) (3) (4) (5) (6) Command Location 11: Receiver #2 Phone Number (digits 1 - 6) Default Values E 1 0 0 0 0 0 1 (1) (2) (3) (4) (5) (6) Digit Positions (1) - (6): 0 - 9 = dialing digits 0 = dial tone detect 2
PAGE 13
Command Locations 14 - 16 SYSTEM 238 Installation Manual Command Locations 14 - 16: RPS Phone Number Order in which the numbers will be dialed Command Location 14 (1) (2) (3) (4) (5) Command Location 15 (6) (1) (2) (3) (4) Command Location 16 (5) (6) (1) (2) (3) (4) (5) (6) Command Location 14: RPS Phone Number (digits 1 - 6) Default Values E 1 0 0 0 0 0 4 (1) (2) (3) (4) (5) (6) Digit Positions (1) - (6): 0 - 9 = dialing digits 0 = dial tone detect 2 = * (DTMF dialin
PAGE 14
Command Locations 17 - 26 SYSTEM 238 Installation Manual Command Locations 17 - 1E: Loop Reporting Codes **Default Values 17 = Loop 1 18 = Loop 2 19 = Loop 3 1A = Loop 4 1 1 1B = Loop 5 1C = Loop 6 1D = Loop 7 1E = Loop 8 0 E 1 0 0 7 (1) (2) (3) (4) (5) (6) Digit Positions (1) & (2): Alarm Reporting Code Digit Positions (3) & (4): Restore Reporting Code Digit Positions (5) & (6): Shunt Reporting Code Only Position (1) is sent for 3/1 and 4/1 formats.
PAGE 15
Command Locations 27 - 29 SYSTEM 238 Installation Manual Command Location 27: Soft Zone A (EMERGENCY) Default Values 0 2 This Zone is identified by the "E" key on the Alpha II and LED keypads. 0 1 3 7 (1) (2) (3) (4) Digit Positions (1) and (2): Emergency Zone Code Report Only Position (1) is sent for 3/1 and 4/1 formats. Positions (1) and (2) are sent for 3/1 Extended, 4/2, and CFSK formats. Program 00 to disable alarm reporting for Emergency zone.
PAGE 16
Command Location 2A and 2B SYSTEM 238 Installation Manual Command Location 2A: Event Reporting Default Values 1 2 1 D 1 (1) (2) (3) (4) (5) (6) See also CL 17 - 1E Digit Positons (5 & 6) Digit Position (2): Restore Receiver Select See Digit Position (1) for programming options.
PAGE 17
Command Locations 2C and 2D SYSTEM 238 Installation Manual Command Location 2C: Opening and Closing Report Codes Default Values B 2 1 C 1 C Digit Position (1): Opening Report Code Valid entries are 0 - F. The User ID # is transmitted after the opening code for 3/1 Extended, 4/2, and CFSK formats. Program 0 to disable Opening Reports.
PAGE 18
Command Locations 2E and 2F SYSTEM 238 Installation Manual Command Location 2E: Audible/Visual Switches Default Values 1 2 1 0 0 0 E Digit Position (1): Entry Pre-alarm Enable (1) (2) (3) (4) 0 0 1 (5) 0 = No 1 = Yes: sounds keypad buzzers during entry delay Digit Position (2): Exit Pre-alarm Enable 0 = No 1 = Yes: sounds keypad buzzers during exit delay Digit Position (3): Bell Reverse Operation 0 = No 1 = Yes: supplies bell voltage in non-alarm state; Bell requires external power s
PAGE 19
Command Locations 30 - 37 & A0 SYSTEM 238 Installation Manual Command Locations 30 - 37: Loop Switches **Default Values 30 = Loop 1 31 = Loop 2 32 = Loop 3 33 = Loop 4 34 = Loop 5 35 = Loop 6 36 = Loop 7 37 = Loop 8 0 3 0 0 0 0 **Default Values are different for each loop. Refer to the SYSTEM 238 Programming Worksheet at the end of this manual for other default values.
PAGE 20
SYSTEM 238 Installation Manual KEYPAD LABEL DRAWER Watchdog Indicator Each keypad comes with a Label Drawer and quick reference operating label. Follow the diagram below to set up the Label Drawer DS1 The SYSTEM 238 is protected by an advanced circuit, called a Watch Dog circuit, that constantly monitors the microprocessor. WATCH As long as the panel has power and is operating DOG normally, the Watch Dog LED (DS1) on the circuit board will flash.
PAGE 21
SYSTEM 238 Installation Manual Keypad Operation Command Summary The majority of the keypad commands apply equally to the LED and Alpha II keypads. Some keypad commands, however, apply to the LCD keypad only.
PAGE 22
SYSTEM 238 Installation Manual Survey of Most Common Questions The following is a summary of the questions most frequently asked of our Technical Support Department. Question: Answer: How do I program the panel with the LED keypad? To program with the LED keypad, enter the Command Location to be programmed, the Data to be programmed and the press the [#] key. (See also pages 6 - 7.
PAGE 23
SYSTEM 238 Installation Manual Question: Answer: How do I interpret the Unit Status Reports? Can the codes be changed? The Reporting Codes for the Unit Status Report is a two-digit code. The first digit is programmed into CL 2A Digit Position (3) and may be any value from 0 - F. The second digit is fixed by the firmware and cannot be changed. Please note that programming a 0 into 2A (3) will disable the report and no Unit Status information will be sent.
PAGE 24
SYSTEM 238 Installation Manual Recommendations for Reducing False Alarms The recommendations contained in this section are designed to assist you in reducing false alarms. The first column contains the Command Locations and Digit Positions in parentheses ( ). The second column is the recommended program option followed by a brief explanation.
PAGE 25
SYSTEM 238 Installation Manual Program Option CL Program Function Comments Audible/Visual Switches 2E (1 & 2) Entry/Exit Pre-Alarm If Digit Postition (1) is programmed for Entry Pre-Alarm, the keypad will beep for the amount of time programmed for the Entry Delay Time (CL 2D (3)). If Digit Position (2) is programmed for Exit Pre-Alarm, the keypad will beep for the time programmed into CL 2D (4), Exit Delay Time.
PAGE 26
SYSTEM 238 Installation Manual THE LIMITATIONS OF YOUR ALARM SYSTEM . Smoke detectors used in conjunction with the alarm system While the SYSTEM 238 is an advanced design security system, it does not offer guaranteed protection against burglary, fire, or other losses. Any alarm system, whether commercial or residential, is subject to compromise or failure-to-warn for a variety of reasons. These include: .
PAGE 27
SYSTEM 238 Programming Worksheet Client: SYSTEM 238 Phone Number: Address: Installer: Date: Control Location: VOLTS AC volts (term 1 and 2): CURRENT Keypads (term 6 and 8): AUX POWER VOLTS (term 5 and 6): SWITCHED AUX (term 5 and 6): + BATTERY VOLTS Under load - AC off: UNSWITCHED AUX (term 6 and 7): + CONTROL LOCATION: LOOP 8 POWERED DEVICES (term 21 and 22): + TOTAL (500 mA allowed): = BREAKER # AND LOCATION: 0 0 0 0 1 0 3 0 9 9 9 0 5 0 7 0 9 9 0 1 2 3 4 5 1 2 3
PAGE 28
1 1 7 1 9 3 5 0 0 0 E E E 1 3 5 0 0 0 0 0 0 1 B 7 0 E 7 0 0 1 D 1 F 2 0 2 1 2 2 2 3 2 4 2 5 2 6 2 7 2 A 1 2 1 3 2 3 1 2 1 2 2 3 1 2 1 2 2 3 1 2 1 2 2 3 1 2 1 1 2 3 1 2 1 1 2 3 1 2 1 9 3 3 1 2 1 9 1 5 0 0 1 3 1 B 1 1 A C 1 1 2 C 1 2 1 0 0 D 0 E 0 3 0 3 2 3 4 3 6 0 0 0 0 1 1 0 0 0 0 0 0 0 0 0 Loop 1 Codes 1 Loop 3 Codes 1 A Loop 5 Codes 1 C Loop 7 C