USER GUIDE WIRELESS USB TO AUDIO KIT Model: 29594 1
TABLE OF CONTENTS Introduction.................................................................................................................................................2 Features......................................................................................................................................................3 System Requirements.................................................................................................................................4 Package Contents.........
INTRODUCTION Thank you for purchasing the TruLink™ Wireless USB to Audio Kit. The TruLink USB to Audio Kit includes everything you need to wirelessly stream audio from your computer to a remote sound system, projector or television. Utilizing Ultra-Wide Band technology, the USB to Audio Kit enables secure, inroom wireless connectivity at distances up to 30 feet between the computer and the audio device. This kit provides an effective wireless audio solution at home, in a classroom or in a conference room.
FEATURES In-room wireless connectivity up to 30 feet Audio conversion from USB to 3.5mm stereo Up to six computers can share one wireless audio device* Ultra-Wide Band operates in the frequency on 3.1GHz to 4.8GHz (WiMedia™ Band Group 1) Certified Wireless™ USB 1.0 compliant WiMedia 1.0 MAC & 1.
SYSTEM REQUIREMENTS Microsoft® Windows® XP 32-bit with Service Pack 3 or higher or Microsoft® Vista® 32-bit/64-bit 4
PACKAGE CONTENTS Wireless USB Host Adapter for your computer Wireless Audio Device Adapter for your audio device Two (2) Dipole Antennas (one for each adapter) 3ft USB A Male/Mini-B Male Cable USB Extender with Cradle One (1) AC Power Adapter (cord approx.
DEVICE OVERVIEW WIRELESS USB HOST ADAPTER 1. Link: Data Connection Indicator • LED is solid when transfer device is connected • LED blinks when data is being transferred 2.
DEVICE OVERVIEW WIRELESS AUDIO DEVICE ADAPTER 2 1. Activity Indicator • LED is solid when display cable is connected. 1 • LED is blinking when data is being transferred. 2. PWR: Power Indicator • LED is solid when power is applied. 3. PWR plug • Power adapter socket 4. USB connector • In wireless mode, this connector is used for cable association • In wired mode, this connector is used for wired operation 5. 3.
SOFTWARE/DEVICE INSTALLATION IMPORTANT NOTE: • If installing on Windows XP, Service Pack 3 (SP3) is required. Verify that this has been installed before installing the Wireless USB to Audio Kit software. • Before installing the software, make sure that the Wireless USB Host Adapter and Wireless Audio Device Adapter are not connected to the computer. Also make sure that the Wireless Audio Device Adapter is not powered. STEP 1-INSTALLING THE SOFTWARE Insert the CD provided and the screen below will appear.
SOFTWARE/DEVICE INSTALLATION This will take you to the TruLink Wireless USB to Audio Kit InstallShield Wizard. Click “Next” to go to proceed with the install. Read and accept the Wireless USB software License Agreement by clicking “Yes”.
SOFTWARE/DEVICE INSTALLATION After the software installs, your installation is complete and you can hit the “Finish” button to exit the wizard. Important: reboot/restart if prompted.
SOFTWARE/DEVICE INSTALLATION STEP 2-CONNECT THE WIRELESS AUDIO DEVICE ADAPTER 1. Connect one of the included dipole antennas to the Wireless Audio Device Adapter. 2. Connect the Wireless Audio Device Adapter 3.5mm Stereo Audio Input to your PC audio speakers, sound system, projector or television using the appropriate cable or adapter types. Plug in the power adapter to the Wireless Audio Device Adapter and opposite end into an AC outlet.
SOFTWARE/DEVICE INSTALLATION STEP 3 -DRIVER INSTALLATION FOR THE WIRELESS USB HOST ADAPTER Your Wireless USB to Audio Kit has been pre-associated for you, meaning the Wireless USB Host Adapter will automatically recognize the Wireless Audio Device Adapter upon being powered and its successful driver installation. After the software installation you should see the Wireless USB Manager icon in your Windows icon tray. Double-click on this icon to open the manager utility.
SOFTWARE/DEVICE INSTALLATION or After you connect the Wireless USB Host Adapter to your computer, Windows will automatically install it and you should get a successful install message in your icon tray such as this figure shows.
SOFTWARE/DEVICE INSTALLATION The Wireless USB Host Adapter will search for the Wireless Audio Device Adapter. When association is confirmed between the devices, the Activity Indicators will light up on the devices. The TruLink DisplayLink Manager utility (Figure: TruLink DisplayLink Manager) will activate and install an icon in the Windows icon tray. The TruLink Wireless USB to Audio Kit is now fully functional and you are ready to use it.
USING THE WIRELESS USB TO AUDIO KIT Wireless USB Manager The Wireless USB Manager is simple and easy to use interface to manage your Wireless USB devices and control your Wireless USB Host Adapter settings. The Wireless USB Manager can be accessed via Wireless USB Manager Icon in the Windows tray (Figure: Wireless USB Manager Icon). Figure: Wireless USB Manager Icon To launch the Wireless USB Manager, double click on the Wireless USB Manager icon.
USING THE WIRELESS USB TO AUDIO KIT The VIEW menu will give the option of what type of devices you wish to display (All Devices, Connected Devices and Not Connected Devices). The OPTIONS menu will give the option to launch Host Settings window and turn the Wireless USB Host Adapter radio on or off. The HELP menu offers quick help on how to connect devices to your Wireless USB Host Adapter.
USING THE WIRELESS USB TO AUDIO KIT To manage the Wireless USB Host Adapter settings, either select “Host Settings” in the “Option” menu of the Wireless USB Manager application or right click on the Wireless USB Manager icon in the Windows tray. GENERAL TAB (Figure: Host Settings – General) 1. Enable this Wireless USB radio: turn on or off the Wireless USB radio. 2. Host name: Change the name of your Wireless USB Host Adapter. 3. Cable association connection rules*: Always, Never or Ask me each time.
USING THE WIRELESS USB TO AUDIO KIT ADVANCED TAB (Figure: Host Settings – Advanced) 1. Channel selection: this function allows you to set manually a radio channel for the wireless communication (combination of Band Group and Channel). For optimal performance, the automatic setting is recommended.
FREQUENTLY ASKED QUESTIONS 1. My Wireless USB Host Adapter is plugged into my computer and my Wireless Audio Device Adapter is powered but I do not hear anything out of my speakers. What’s wrong? Check the Wireless USB Manager to see if there is an icon for your Wireless Audio Device Adapter. If there is no icon, try unplugging and then plugging in your Wireless USB Host Adapter to reload the Wireless Audio Device Adapter.
TECHNICAL SPECIFICATIONS Systems Information Operating System Support: Microsoft XP 32-bit; Microsoft Vista 32-bit/64-bit Operating Range: Up to 30 feet (10 meters) PHY Data Rate: 53.3Mbps, 80Mbps, 106.6Mbps, 160Mbps,200Mbps, 320Mbps, 400Mbps, 480Mbps Frequency: 3.1GHz to 4.8GHz (WiMedia Band Group 1) RF Modulation Type: QPSK/DCM Number of Channels: 7 Channels (3 FFI + 4 TFI) USB Specification: Certified Wireless USB 1.
CABLES TO GO™ WARRANTY STATEMENT At Cables To Go, we want you to be totally confident in your purchase. That is why we offer a one year warranty on this device. If you experience problems due to workmanship or material defect for the duration of this warranty, we will repair or replace this device. To request a Return Merchandise Authorization (RMA) number, contact customer service at 1-800-293-4970 or www.cablestogo.com. Cables To Go 3555 Kettering Blvd. Moraine, OH 45439 1-800-826-7904 www.cablestogo.
IMPORTANT SAFETY INFORMATION ! Do not plug the unit in any outlet that does not have enough current to allow the device to function. Refer to the specifications in this manual for power level of the unit. ! Liquid: If this unit or its corresponding power adapter has had liquid spilled on or in it, do not attempt to use the unit. Do not attempt to use this product in an outdoor environment as elements such as rain, snow, hail, etc. can damage the product.
APPENDIX ASSOCIATION WITH OTHER DEVICES ASSOCIATION CONCEPT In order to establish a secure wireless connection, both your Wireless USB Host Adapter and the Wireless Audio Device Adapter must exchange information about each other. This is done via cable or PIN association. ASSOCIATION PROCESS If you purchase additional Certified Wireless USB host adapters, such as the TruLink Wireless USB Host Adapter (part #29578), you will need to associate them with your Wireless Audio Device Adapter.
APPENDIX CABLE ASSOCIATION PROCEDURE Cable association steps. Examples/Figures shown are used with the association of the TruLink Wireless Audio Device Adapter (Part # 29595) when used with the TruLink Wireless USB Host Adapter (part #29578). This process will vary by manufacturer of your Wireless USB host adapter. 1. Make sure that the Wireless USB host adapter utility is running. Check your Windows tray for the Wireless USB Manager icon (Figure: Wireless USB Manager). 2.
APPENDIX Associated Certified Wireless USB Devices will appear as icons in the Wireless USB Manager. When the Wireless USB devices are connected, the icon will appear in color (Figure: TruLink Wireless Audio Device Adapter Connected). Figure: TruLink Wireless Audio Device Adapter Connected Note: You may rename or delete the Wireless USB Device by right-clicking the device icon in the Wireless USB Manager and select “rename”. You can also delete a wireless device adapter association by selecting “delete”.
APPENDIX PIN ASSOCIATION PROCEDURE PIN association steps: Examples/Figures shown are used with the association of the TruLink Wireless Audio Device Adapter (Part # 29595) when used with the TruLink Wireless USB Host Adapter (part # 29578). This process will vary by manufacturer of your Wireless USB host adapter. 1. Make sure your Wireless Audio Device Adapter is powered on and the Wireless USB Host Adapter is connected to your computer. Click the “Discovery Mode” button (Figure: Discovery Mode Screen).
APPENDIX 2. The Wireless USB Host Adapter will search for the Wireless Audio Device Adapter within its range. Note that this operation can take up to 20 seconds (Figure: Discovery Mode in Process). Figure: Discovery Mode in Process 3. Once the Wireless USB Host Adapter and the Wireless Audio Device Adapter have exchanged security information, the following dialog will appear.
APPENDIX 4. Enter the PIN of the Wireless Audio Device Adapter (4-digit PIN) and click Accept Association (Note: the default PIN is “1234”). The Wireless Audio Device Adapter and Wireless USB Host Adapter are now associated and ready for operation. PIN CHANGE PROCEDURE The default PIN setting for the Wireless Audio Device Adapter is “1234”. This section gives you the instructions to change the PIN to another 4-Digit value. IMPORTANT: The application used to change the PIN is not supported in Vista 64bit.
APPENDIX 3. While the program is searching for the device, connect the USB cable between your Wireless Audio Device Adapter and any available USB port on your computer.
APPENDIX 4. Click Install this driver software anyway. 5.
APPENDIX 5. Enter a 4-Digit PIN (0-9) and click OK. 6. If your PIN is valid, a window displaying your new PIN will appear. Press OK. Your PIN has been successfully changed. IMPORTANT: please exit the Trulink PIN Utility application (Exit button as shown on figure in step 5) before unplugging the USB cable between your Wireless Audio Device Adapter and your PC.
32
For more information on this product or to check for updated drivers, manuals or frequently asked questions please visit our website. www.cablestogo.com VER. 1.0.6.30.
